Transcript MOS Transistors

MOS Transistors
• The gate material of Metal
Oxide Semiconductor Field
Effect Transistors was original
made of metal hence the name.
• Present day devices’ gate
material is polycrystalline
silicon (polysilicon).
• The transistor (nMOS or
pMOS) is a 4-terminal device.
• n+(nMOS) or p+ (pMOS)
regions can be considered
interchangeable in definining
the drain and source terminals.
Transistor Operation (Simplistic View)
• The gate is a control input.
• For the n-type device we have
that if the gate voltage is raised
it creates an electric field that
starts to attract free electrons to
the Si-SiO2 interface.
• Further increase of the gate
voltage results in a thin region
under the gate being inverted to
an n-type semiconductor.
• This forms a conducting path of
electron carriers between source
and drain.
• For digital circuits we simplify
the transistor operation such
that a voltage value equivalent
to the power supply voltage
applied to the gate terminal is
logic 1 and implies that the
switch is ON.
• This condition allows a logic 1
or logic 0 at the drain to be
transferred to the source.
• A logic 0 applied to the gate of
the pMOS implies that the
device is ON. The pMOS is
OFF otherwise.
CMOS Logic
• Complementary Metal Oxide
Semiconductor (CMOS),
implies that for every n-type
device on a circuit there is a ptype device.
• Examples are inverters, NAND,
AND, NOR, OR etc.
• An n-input NAND will have n
pMOS devices and n nMOS
devices.
• In general CMOS circuits have
a pull-up (pMOS) and a pulldown (nMOS) network.
• An inverter has 4 possible
output states namely the
crowbarred (X), logic 1, logic 0
and high impedance (Z) How?.
• Observe that two or more ntype or p-type transistors placed
in series constitute an ANDing
operation while devices placed
in parallel constitute an OR
function.
• This observation allows for the
construction of compound gates
Compound Gates
• Given the function:
F = D + A•(B + C)
• We desire to represent this
expression using CMOS logic.
• We apply De Morgan’s
theorems to get:
F = D•(A + B•C)
• The function above represents
the pull-up network.
• The original function uncomplemented represents the
pull-down network.
• Key in the synthesis of a
complex CMOS gate is to note
that the pull-up network is the
dual of the pull-down network.
• Complementary CMOS is
naturally inverting and thus
implements only functions such
as NAND, NOR and XNOR.
• Noninverting Boolean functions
(AND, OR or XOR) cannot
represented in CMOS in a
single stage. They require an
additional inverting stage.
Pass Transistors
• A logic 1 will drive a significant
capacitive load in a shorter time
if the voltage of the signal is
close to the power supply
voltage VDD.
• Similarly a logic 0 will quickly
discharge a capacitor if it is as
near to 0V as possible.
• An nMOS device is a near
perfect switch for transmitting
logic 0 while the pMOS is good
for transmitting logic 1.
•
The nMOS degrades a logic 1 as
does the pMOS a logic 0.
IN
VOUT
•
Not such a great idea since we can
neither pass good zeros or ones.
Pass Transistors
•
•
Scenario above assumes a grounded source
What if source > 0 i.e. both source and drain can attain a value greater
than 0?
– e.g. pass transistor passing VDD
VDD
VDD
Pass Transistors
•
Vg = VDD
– If Vs > VDD-Vt, Vgs < Vt
– Hence transistor would turn itself off
•
nMOS pass transistors pull no higher than VDD-Vtn
– Called a degraded “1”
– Approach degraded value slowly (low Ids)
•
pMOS pass transistors pull no lower than Vtp
Pass Transistor Ckts
VDD
VDD
VDD
VDD
VDD
VDD
VSS
VDD
VDD
Pass Transistor Ckts
VDD
VDD
VDD
VDD
VDD
VDD
Vs = VDD-Vtn
Vs = |Vtp|
VDD-Vtn VDD-Vtn
VDD
VDD-Vtn
VDD
VSS
VDD-2Vtn
VDD-Vtn
Pass Transistor Logic
• Sometimes we have a need to
pass a signal based on a clock
or trigger’s arrival at the gate of
a pass transistor.
• We can prevent the degradation
of D, by using a
Complementary Switch (CSwitch).
CLK
CLK
D
• The transistor between the
inverters is a pass transistor. It
serves to pass D to the input of
inverter 2.
D
CLK
• We are now in a position to
pass both good 1s and 0s.
Multiplexers
• Complementary switches may
be used to select between a
number of inputs, thus forming
a multiplexer function.
• Provide the Equation for the 4:1
mux below.
•
•
•
•
A
Vout
B
C
D
S1
S1 S2 S2
•
For the multiplexer shown we can
improve signal integrity by using
complementary switches.
Memories can also be designed using
these switches.
A D-Latch would consist of a data input
(D), clock input (CLK) and outputs Q
and its inverse.
A D-Latch is considered level sensitive
if the state of the output is dependant on
the level of the clock signal.
By combining two level sensitive latches
with one changing the output state when
the clock is at logic 1 while the other
changes when the clock is at logic 0, one
may construct an edge triggered register.
Latches and Flip-Flops
phi1
Q
CLK
D
D
Q
CLK
CLK
CLK
•
phi2
Refer to text book for the
construction of an edge triggered D
Register. The figure shows a
positive level sensitive latch.
phi1
phi1
Q
phi2
phi1
Q
phi2
phi2
• The Figure above depicts an
edge triggered flip-flop if single
phase clocking is used.
• Two phase clocking alleviates
to some degree the set-up and
hold time issues.