Transcript final_ped_dec6_11am

Automation Of BJT PNP Silicon versus Simulation
William Berry, Alex Chee, Chris Soh, Dalton Young
Industry Advisor: Mr. Bob Peddenpohl; Faculty Advisor: Dr. Joseph Elias
Abstract
Technical Description
During semiconductor design, it is necessary to compare data from physical
testing of a device to simulation data to validate simulation SPICE models for future
designs.
Historically, the BJT versus silicon measurement comparisons at Cypress
Semiconductor have been done either manually, with all running simulations, formatting
data, and plotting data performed by an engineer; or autonomously, with non-native
simulation tools which are used specifically to avoid the manual process.
This project aims to automate the process of formatting the measured data file
from an HP 4156 Semiconductor Parametric Analyzer, performing the simulations
across Cypress’ process models of a device using Mentor’s Eldo SPICE circuit
simulator, formatting and plotting the output data from simulations alongside the original
measured data, and arranging the plots and data in an intuitive format for Cypress
design engineers (an existing Cypress format).
Old Method
Objective
The objective of this project is to save money and increase productivity for
Cypress Semiconductor. On average, Cypress creates BJT models once a quarter,
and this task takes an engineer 1 day, with a cost of approximately $1K. Bigger
savings to Cypress, however, come through quality assurance of the SPICE model.
In the most extreme case, an inaccurate SPICE model could result in a new all-layer
tapeout that would cost Cypress approximately $500K for a new mask set.
vs.
New Method
MEASURE DC CURVES OF BJT
MEASURE DC CURVES OF BJT
EXTRACT SPICE MODEL
EXTRACT SPICE MODEL
GET BIAS CONDITIONS FOR
SIMS FROM MEAS.
REPEAT
~150 TIMES (PROCESS,
CURVES,
TEMPERATURE)
SIMULATE ELDO MODEL
RUN PROGRAM
LOAD SIM & MEAS INTO
EXCEL
QA MODEL
QA MODEL
High Level Design
PUBLISH MODEL
RESULTS ON WEB
PUBLISH MODEL
RESULTS ON WEB
(ABOVE) A comparison of the old and new methods. Note especially the red boxes, which mark
particularly time-consuming or tedious processes that are eliminated by this automation.
A detailed view of the process, in phases
The actual process consists of four phases to get from start to finish. The
phases were created in parallel, but are made to run end-to-end, with each one
processing or manipulating the data generated by the previous phase. As seen
above phase one of the process consists of parsing BSIMPRO++ measured data files
(from HP4156) and creating metafiles (data files in memory) in the metafile handler
for each plot to be made. Bias conditions and other information are also extracted in
phase one. Phase two consists of creating the circuit files for each type of plot to
simulate and running the actual Eldo simulations for all the specified process models
(specified in the user control file) using the load-balancer, as well as collecting the
data post-simulation. Phase three consists of plotting all the data into .png files using
gnuplot and generating .csv data files corresponding to the plots. Phase four
consists of generating the actual HTML webpage and linking to the data (again, in a
familiar format for Cypress design engineers).
Conclusion
The program has been completed, and has been used for the Cypress
Semiconductor 150nm programmable technology. Of the original deliverables
specified, all will be delivered before the end of the semester, and only the user
document has taken extra time. The program will meet all specifications provided by
Cypress, and should be extensible for future use.
Future Work
Due to its modular construction, there is already discussion of modifying the
existing code to process npn-type devices, as well as handle new plot-types and input
file formats.
A high-level view of the automation process
The new process is started by initial input from the HP4156 Semiconductor
Parametric Analyzer. The HP4156 generates data files of parametric sweeps from a
silicon-based BJT, for which Cypress develops SPICE models. This HP4156 data file is
then read and split into the different plot types which were taken on the analyzer, and
each of the measured data sets is simulated using Mentor’s Eldo circuit simulation tool.
Simulations are performed for different process models developed by Cypress for the
different plot types using a load-balancing tool across a cluster, and the resulting data is
then formatted and plotted using the gnuplot plotting program. The final plots and their
data are then arranged into an HTML page for design engineers to use and present.
The program was developed to be very modular, as seen in the communication
between phases above. All data is passed through the central data-handling
mechanism, making the addition of new processes or methods simple. Inside that
mechanism, data is separated on a per-plot basis, making modification of a single class
of plots, or addition of new plot types and functions, very simple for future work.
(ABOVE) The Final Results: A Beta-Ic (Gain) Plot, an Ib,Ic-Vbe (Gummel) Plot, and an Ic-Vce
(Characteristic) Plot, as generated by the program.
(BELOW) The HP4156 Semiconductor Parametric Analyzer, in use.
Acknowledgement
The group would like to acknowledge the following people for their invaluable
assistance on the project:
Mr. Bob Peddenpohl, for his continual guidance and assistance.
Dr. Joseph Elias, for helping to guide the group during the early development stages.
Dr. Regina Hannemann, for her assistance in keeping the group on-task and up-todate with required reports and reviews.
Sponsors
The group would like to thank both Eta Kappa Nu and Cypress Semiconductor for
sponsoring EE 499.