Transcript Device

EE5900 Advanced
Algorithms for
Robust VLSI CAD
Dr. Shiyan Hu
Office: EERC 731
[email protected]
Device
Adapted and modified from Digital Integrated Circuits: A Design Perspective
by Jan M. Rabaey, Anantha Chandrakasan, and Borivoje Nikolic.
© Digital Integrated Circuits2nd
Devices
Goal of this chapter
Present intuitive understanding of device
operation
 Introduction of basic device equations

© Digital Integrated Circuits2nd
Devices
MOS Transistor Types and Symbols
D
G
S
NMOS
D
G
S
PMOS
© Digital Integrated Circuits2nd
Devices
Circuit Under Design
VDD
VDD
M2
M4
Vout
Vin
M1
© Digital Integrated Circuits2nd
Vout2
M3
4
Devices
Circuit on the Chip
A transistor
© Digital Integrated Circuits2nd
Devices
The MOS (Metal-Oxide-Semiconductor)
Transistor
Polysilicon
© Digital Integrated Circuits2nd
Aluminum
Devices
Simple View of A Transistor
A Switch!
An MOS Transistor
VGS  V T
|VGS|
Ron
S
© Digital Integrated Circuits2nd
D
Devices
Silicon Basics
Transistors are built on a silicon substrate
 Silicon forms crystal lattice with bonds to
four neighbors

© Digital Integrated Circuits2nd
Devices
Doped Silicon



Silicon is a semiconductor
Pure silicon has no free carriers and conducts poorly
Adding dopants increases the conductivity
 extra electrons (doped Borons) – n-type
 missing electrons (doped Arsenic/Phosphorus)
more holes) – p-type
n-type
© Digital Integrated Circuits2nd
p-type
Devices
NMOS Transistor
Diffusion
© Digital Integrated Circuits2nd
Devices
NMOS - II
Refer to gate, source, drain and bulk
voltages as Vg,Vs,Vd,Vb, respectively.
 Vab=Va-Vb
 Device is symmetric. Drain and source are
distinguished electrically, i.e., Vd>Vs.
 P regions have acceptor (Boron)
impurities, i.e., many holes.
 N regions have donor
(Arsenic/Phosphorus) impurities, i.e.,
many electrons.
 N+ and P+ are heavily doped N and P
regions, respectively.

© Digital Integrated Circuits2nd
Devices
NMOS - III
Gate oxide are insulators, usually, silicon
dioxide.
 Gate voltage modulates current between
drain and source, how?

© Digital Integrated Circuits2nd
Devices
Enhancement NMOS
© Digital Integrated Circuits2nd
Devices
Enhancement NMOS - II
Does not conduct when Vgs=0, except
that there is leakage current.
 When Vgs is sufficiently large, electrons
are induced in the channel, i.e., the device
conducts. This Vgs is called threshold
voltage.

© Digital Integrated Circuits2nd
Devices
Enhancement NMOS III
Positively Changed
Negatively Changed
© Digital Integrated Circuits2nd
Devices
Enhancement NMOS - IV
When Vgs is large enough, the upper part
of the channel changes to N-type due to
enhancement of electrons in it. This is
refereed to as inversion, and the channel
is called n-channel.
 The voltage at which inversion occurs is
called the Threshold Voltage (Vt).
 A p-depletion layer have more holes than
p-substrate since its electrons have been
pushed into the inversion layer.
 Does not conduct when Vgs<Vt (Cut-off).

© Digital Integrated Circuits2nd
Devices
Enhancement NMOS V
© Digital Integrated Circuits2nd
Devices
Enhancement NMOS - VI
When Vgs>Vt, the inversion layer (n
channel) becomes thicker.
 The horizontal electrical field due to Vds
moves electrons from the source to the
drain through the channel.
 If Vds=0, the channel is formed but does
not conduct.

© Digital Integrated Circuits2nd
Devices
Case when Vds=0
© Digital Integrated Circuits2nd
Devices
Linear Region
© Digital Integrated Circuits2nd
Devices
Linear Region - II
When Vgs>Vt and Vgd>Vt, the inversion
layer increases in thickness and
conduction increases.
 The reason is that there are non-zero
inversion layer at both source and drain
(our previous analysis works for both Vgs
and Vgd).This is called linear region.
 Vgd>Vt means that Vgd=Vgs-Vds>=Vt, i.e.,
Vds<=Vgs-Vt
 Ids depends on Vg, Vgs and Vds.

© Digital Integrated Circuits2nd
Devices
Saturation Region
© Digital Integrated Circuits2nd
Devices
Saturation Region - II
When Vgs>Vt and Vgd<Vt, we have nonzero inversion layer at source but zero
inversion layer at drain.
 Inversion layer is said to be pinched off.
This is called the saturation region.
 Vgd<Vt means that Vgs-Vds<Vt, i.e.,
Vds>Vgs-Vt.
 Electrons leaves the channel and moves
to drain terminal through depletion region.

© Digital Integrated Circuits2nd
Devices
Saturation Region - III
In saturation region, the voltage difference
over the channel remains at Vgs-Vt. This
is because if Vds=Vgs-Vt, the inversion
layer is barely pinched off at the drain. If
Vds>Vgs-Vt, the channel is pinched off
somewhere between the drain and source
ends. Thus, the voltage applied across the
channel is Vgs-Vt.
 As a result, Ids depends on Vgs alone in
this region, so we cannot keep raising Vds
to get better conduction.

© Digital Integrated Circuits2nd
Devices
Summary
Three regions of conduction
 Cut-off: 0<Vgs<Vt
 Linear: 0<Vds<Vgs-Vt
 Saturation: 0<Vgs-Vt<Vds
 Vt depends on gate and insulator
materials, thickness of insulators and so
forth – process dependant factors, and
Vsb and temperature – operational factors.

© Digital Integrated Circuits2nd
Devices
Analysis (for linear region)
VGS
VDS
S
G
n+
–
V(x)
ID
D
n+
+
L
x
p-substrate
B
MOS transistor and its bias conditions
© Digital Integrated Circuits2nd
Devices
Analysis - II

Denote by V(x) the voltage at a point x
along the channel. The gate-to-channel
voltage is Vgs-V(x). Since it needs to be >
Vt for every point along the channel, the
charge per unit area at x is

Cox is the capacitance per unit, which is
where is a constant called the
permittivity of the gate oxide and tox is the
thickness of gate oxide.
© Digital Integrated Circuits2nd
Devices
Analysis - III
I
1
Q
1
W
Gate width W, so the total charge is QW.
 I=QW/t=QWv, v being velocity of carrier.
 Given surface mobility u of electrons,
which depends on process, an empirical
formula for v is
 We have
 Integrate x from 0 to L, we have


For saturation region, replace Vds by VgsVt, we have
. It does
not depend on Vds.
© Digital Integrated Circuits2nd
Devices
Summary - II

Three regions of conduction
 Cut-off: 0<Vgs<Vt, I=0
 Linear: 0<Vds<Vgs-Vt,

Saturation: 0<Vgs-Vt<Vds
© Digital Integrated Circuits2nd
Devices
PMOS
© Digital Integrated Circuits2nd
Devices
PMOS - II
Dual of NMOS
 Three regions of conduction
 Cut-off: 0>Vgs>Vt
 Linear: 0>Vds>Vgs-Vt
 Saturation: 0>Vgs-Vt>Vds
 Current computation is the same as NMOS
except that the polarities of all voltages
and currents are reversed.
 Mobility of holes u in PMOS is usually half
of the mobility of electronics in NMOS due
to process technology.

© Digital Integrated Circuits2nd
Devices
Sub-threshold conduction (Leakage)
Vgs<Vt, cut-off and I=0. Not true.
 In practice, for Vgs<Vt,

I is exponentially dependent on Vgs. Id0
and n are experimentally determined, k is
Boltzmann’s constant and T is
temperature.
 Source of standby power consumption in
portable devices.
 Some extremely low-power circuits use
sub-threshold conduction, e.g., digital
watch.

© Digital Integrated Circuits2nd
Devices
Transistor Equivalent Resistance

In linear region, R=V/I, so

In saturation region, the voltage applied
across the channel is Vgs-Vt. Thus,

Roughly speaking, channel resistance
inversely depends on W since
© Digital Integrated Circuits2nd
Devices
Transistor Resistance - II
Larger gate width (larger gate area) ->
smaller resistance -> device runs faster
 This means that power/area increases with
delay decreases. A lot of power-delay
tradeoff like this.

© Digital Integrated Circuits2nd
Devices
Overlap Capacitance
Polysilicon gate
Source
Drain
xd
n+
xd
W
n+
Ld
Top view
Gate oxide
tox
n+
L
n+
Cross section
Overlap capacitance=2Cox Xd W
© Digital Integrated Circuits2nd
Devices
Channel Capacitance
G
G
CGC
CGC
D
S
G
Cut-off
CGC
D
S
D
S
Resistive
Saturation
Larger gate width -> Larger capacitance
© Digital Integrated Circuits2nd
Devices
In Standard Cell Library





A gate type has multiple gate sizes (widths)
Larger gate width means larger gate capacitance and
smaller driving resistance.
Thus, for a gate type, we have a variety of transistors
with different capacitance and resistance tradeoff.
Larger width means larger capacitance and thus
larger power due to charging and uncharging the
capacitance.
Usually, larger width transistor has smaller delay.
© Digital Integrated Circuits2nd
Devices
Technology Scaling


Devices scale to smaller dimensions with advancing technology.
A scaling factor S describes the ratio of dimension between the
old technology and the new technology. In practice, S=1.2-1.5.
© Digital Integrated Circuits2nd
Devices
Technology Scaling - II












In practice, it is not feasible to scale voltage since different ICs in
the system may have different Vdd. This may require extremely
complex additional circuits. We can only allow very few different
levels of Vdd.
In technology scaling, we often have fixed voltage scaling model.
W,L,tox scales down by 1/S
Vdd, Vt unchanged
Area scales down by 1/S2
Cox scales up by S due to tox
Gate capacitance = CoxWL scales down by 1/S
scales up by S
Linear and saturation region current scales up by S
Current density scales up by S3
P=Vdd*I, power density scales up by S3
Power consumption is a major design issue
© Digital Integrated Circuits2nd
Devices
Summary

NMOS
 Cut-Off, Linear and Saturation Regions
 How to compute I
PMOS is the dual device of NMOS
 I-V characteristics of MOS transistors

 Resistance
 Capacitance
© Digital Integrated Circuits2nd
Devices