Transcript Linux DVR Manual ppt File (Final Version)

Linux DVR Self-Kit
User’s Guide
0
 The contents of this User’s Manual shall not be reproduced arbitrarily without
prior approval.
 The product of this User’s Manual may be modified without advance notice for the
reasons of upgrading, etc.
 The trademarks mentioned in this User’s Manual are registered trademark and
unique trademark of each relevant company.
 Please contact LeadTech Corporation for any unclear matters or errors to be
corrected in the contents of this User’s Manual.
Copyright ⓒ 2005
LeadTech Corp. All Rights Reserved
Self-Kit Series, V2.86
Oct 2005
1
Matters to be Noted
 Turn off the power of Linux DVR without fail before the installation.
 The persons other than professional installer should not open the cover of the case of
this product at their own discretion.
 When verifying internal part of this product for system upgrade or repair of trouble,
please ask to the place of purchase without fail.
 When installing this product, maintain approximately 15cm of distance from other
nearby equipment.
 Be careful not to apply impact or shaking when Linux DVR is moved or in operation.
 Do not install at the place where there is strong magnetism or radio wave.
 Surface of wall for smooth radiation of heat. Be attentive no conductive material is
put inside the cooling ventilation hole.
 Please avoid installing at the places of high temperature such as nearby direct
sunlight or heater.
 Please avoid installing at the places where are extremely cold or highly humid.
 Before connecting the power, check the using power of AC100~240V 50/60Hz
without fail.
 This unit is designed for indoor use. Operating ambient temperature must not range
beyond (0℃~+40℃)
2
Table Of Contents
Chapter 1. Self-Kit Introduction ………………………………………
4
I. Part of Self-Kit ………………………………………………………………………….
1. LDB-400MX ………………………………………………………………………….
2. LDB-800MX ………………………………………………………………………….
3. LDB-1600MX …………………………………………………………………………
4. Option …………………………………………………………………………………
5. Network Client Application (Eye-Linker) Install CD ……………………….
II. Self-Kit Installation Guide ………………………………………………………….
1. Self-Kit Hardware Installation Guide ………………………………………….
2. How To Install The Initial Setup ………………………………………………….
5
5
6
7
8
9
9
9
12
Chapter 2. DVR Application User’s Guide ……………………………
15
I. Usage of Remote Controller and Keyboard ……………………………………..
1. Function of Remote Controller and Keyboard ………………………………..
2. By Remote Controller ……………………………………………………………….
II. Surveillance Mode (Main GUI) …………………………………………………….
III. Setup Mode ………………………………………………………………………......
1. General Setup …………………………………………………………………………
2. Camera Setup …………………………………………………………………………
3. Color Setup …………………………………………………………………………....
4. Motion Area Setup …………………………………………………………………...
5. Schedule Setup ……………………………………………………………………....
6. Network Setup ………………………………………………………………………..
7. Sensor Setup ………………………………………………………………………….
8. Alarm Setup …………………………………………………………………………...
9. PTZ Control Mode …………………………………………………………………….
10. Backup Mode ………………………………………………………………………...
11. System Administration …………………………………………………………….
12. Search Mode ………………………………………………………………………….
IV. DVR Application Troubleshooting Guide ………………………………………..
16
16
18
19
22
23
25
27
28
29
31
33
34
35
36
39
41
44
Chapter 3. Eye-Linker User’s Guide ……………………………………
47
I. Features of Eye-Linker …..…………………….………………………………………
II. Installation guide of Eye-Linker .…………………………………………………..
1. System spec. to be recommended for Eye-Linker .…………………………..
2. Installation steps for Eye-Linker …………………………………………………
3. To run Eye-Linker …..……….……………………………………………………….
III. User’s guide of Eye-Linker ..……………..…………………………………………
IV. Eye-Linker Troubleshooting Guide ……….……………………………………….
48
50
50
50
52
53
67
3
Chapter 1.
Self-Kit Introduction
4
I. Part of Self-Kit
1. LDB-400MX
SM100M * 1EA
4CH Video
Input Cable (BNC) * 1EA
¹ Flash Memory - 32MB
(IDE 40Pin Compatible Type)
※ ¹ Flash Memory
Embedded Linux OS, Device Driver,
DVR Application Software Installed.
5
I. Part of Self-Kit
2. LDB-800MX
SM100M * 2EA
4CH Video
Input Cable (BNC) * 2EA
Flash Memory - 32MB
(IDE 40Pin Compatible Type)
6
I. Part of Self-Kit
3. LDB-1600MX
SM400M * 1EA
8CH Video
Input Cable (BNC) * 2EA
Flash Memory - 32MB
(IDE 40Pin Compatible Type)
7
I. Part of Self-Kit
4. Option
Remote Controller and Receiver
Remote Controller
Receiver
4-1. Sensor Board
DIO 400 Board
5. Network Client Application (Eye-Linker) Installation CD
*Note*
Eye-Link Installation CD including
- Eye-Linker
- Self-Kit User’s Guide
Eye-linker Installation CD
8
II. Self-Kit Installation Guide
1. Self-Kit Hardware Installation Guide
LDB-400MX (30/30)
Self-Kit Installation Guide
LDB-400MX (30/30)
9
II. Self-Kit Installation Guide
LDB-800MX (60/60)
Self-Kit Installation Guide
LDB-800MX (60/60)
10
II. Self-Kit Installation Guide
LDB-1600MX (120/120)
Self-Kit Installation Guide
LDB-1600MX (120/120)
11
II. Self-Kit Installation Guide
2. How To Install The Initial Setup
1) System booting after hooking HDD
※ This will be changed as per
main board
2) HDD information in System Manager
[System Manager ]
Normal viewing at initial setup
HDD1 : Flash Memory (to be
fixed)
HDD2 : Primary Slave
HDD2 : Secondary Master
HDD2 : Primary Slave HDD
“Enter” after “Confirm” at
initial setup (to start
formatting HDD)
12
II. Self-Kit Installation Guide
3) HDD formatting
[HDD Formatting ]
4) Running the DVR Application
To Run the DVR application
after HDD Formatting.
“Enter” after “Confirm”
13
II. Self-Kit Installation Guide
5) waiting
“Enter”
.dvdr
DVR Application Program is
working.
14
Chapter 2.
DVR Application User’s Guide
15
I. How To Use The Remote Controller And Keyboard
1. Function of Remote Controller and Keyboard
POWER
1~16
DVR Power ON/OFF (Currently not available)
Full Screen for each selected channel
FREEZE
No applicable function
BACKUP
DVR Backup Mode
REC
[Surveillance Mode]
Full recording regardless of each setup data
[Motion/Schedule Mode]
Setup for motion and schedule
CANCEL
To shift to high level menu at setup mode
or to cancel the value in setup mode
ENTER
To shift to low level menu at setup mode
or to apply the value at setup mode
To change the value at setup mode
To switch channel at the Surveillance Mode
To change the value at setup mode
To switch channel at the Surveillance Mode
To Move cursor at setup mode
To Move cursor at setup mode
REW at the Search Mode
FF at the Search Mode
Play Start / Play Pause (Toggle)
Stop playing
SEARCH
Search Mode
SETUP
Setup Mode
DIV
[Surveillance Mode] 16–13–9–8–4–1-16
[Search Mode] 16-9-4-1-16
PTZ
PAN/TILT Mode
Remote Controller
16
I. How To Use The Remote Controller And Keyboard
*Note*
All functions are the same as Remote controller.
Keyboard
17
I. How To Use The Remote Controller And Keyboard
2. By remote controller
SETUP : SETUP Mode
Surveillance Mode
CANCEL : Surveillance Mode
ENTER :to shift low level
menu
Setup Mode
CANCEL : to shift to high level menu
then to save the change as per message.
(YES, NO, CANCEL)
CANCEL : to shift to high
level menu
ENTER : to come out to high level menu
after fixing the changing value
CANCEL : to come out to high level
menu
First level of Setup
ENTER : to shift to low
level menu
Second level of Setup
ENTER : to shift to low
level menu
² Value of Setup
※ ² Value of Setup
changing the value to use
in the remote controller
In the motion and schedule mode,
REC key for changing the values
18
II. Surveillance Mode (Main GUI)
Surveillance Mode – live monitoring mode
2
3
4
5
6
7
1
8
[Surveillance Mode]
1
Current Mode : Surveillance Mode
2
Monitoring area
3
Present time and date
4
status of camera
Recording status
Motion Detection status
5
Sensor status (working status is to be on by Yellow color )
6
Alarm status (working status is to be on by Yellow color)
7
Number of user to be connected with Network (Eye-Linker)
8
HDD status (current storage volume / maximum storage capacity)
19
II. Surveillance Mode (Main GUI)
Monitoring area
CAM005 1
enlarge
2
[Monitoring area]
1
Camera ID
2
Camera status (I con)
[enlarged viewing]
Storage status
schedule status
PAN/TILT
Camera and sensor
*Note*
Each ICON shows the current
settings
Motion Detect storage status
TV OUT status
TIP #1. “DIV” function
Window can be divided by “DIV” button at Surveillance Mode
[16]
[13]
[9]
[1]
[4]
[8]
20
II. Surveillance Mode (Main GUI)
TIP #2.
,
function
[camera 1,2,3,4]
[camera 5,6,7,8]
[camera 13,14,15,16]
[camera 9,10,11,12 ]
TIP #3. “REC” function
To record all data from all cameras regardless of setup data of each camera,
Whenever want to be back to the setup data, push “REC” button one more time .
[ camera status in normal ]
[on recording data from all camera]
21
III. Setup Mode
Setup Mode
2
1
[Setup Mode-main window]
1
Please Enter Password : Enter the password for setup
(Default Password : 0000  “10”can be applied to “0”)
2
SETUP MODE :
TIP #4. Using remote controller in Setup Mode
To shift the menu :
To choose the menu :
ENTER
To shift to low level menu :
ENTER
To shift to high level menu :
CANCEL
To change setup data :
To cancel setup data :
To apply setup data (no recording) :
REC
CANCEL
ENTER
22
III. Setup Mode
1. General Setup
1
2
3
4
5
6
7
8
9
[General Setup]
1
New Password : Only want to change password
2
Retype New Password
3
Channel Auto Switching : Switching camera channel automatically when the window
is 13,9,8,4 division screen and full screen.
4
TV OUT : TV output for selected camera channel. Selected camera channels in TV are
switching every selected seconds
5
Rebooting : Rebooting every selected days at selected hour (00~23)
No rebooting when the value is Every 000 Days
6
Set Date : Changing the system date and time
( Warning! When time is newly set, all of the stored data will be deleted.)
7
Water Mark : For the back up of JPG file
8
HDD : Warning of insufficient space of Hard disk
9
Video Type : Video Type (NTSC/PAL) and number of cameras
23
III. Setup Mode
TIP #5. Settings applied after rebooting in General Setup
Set Date – Warning! When time is newly set, all of the stored data will be deleted
Video Type – NTSC / PAL
[To confirm saving the changes]
[To Confirm rebooting]
24
III. Setup Mode
2. Camera Setup
2
1
3
4
5
6
7
10
8
9
1
Camera
2
I D : ID of camera. Basic setup is set for ‘CAM+Camera No. (Max 8 characters)
3
Frame rate : Frame rate per sec
4
PTZ Type / ID: Type of pan/tilt Camera and ID
5
Recording Status: Full Record / Do Not Record / Schedule
6
Motion Sensitivity :
Sensitivity : 1 to 10, 10 is the most sensitive
Post Recording : recording time after the motion is detected
Display : Showing blue area in the Surveillance Mode when the motion is detected
25
III. Setup Mode
TIP #6. Motion Sensitivity in Surveillance Mode
(Example) Sensitivity : 06
Post Recording : 03 sec
Display : ON
When the motion is detected, it will be recorded during 3 sec after the detection. It
shows blue box when the motion is detected.
It shows blue box when
the motion is detected
[Screen of Surveillance Mode]
7
Image Quality : Setting can be done from 1 to 5, and 5 is the best image quality
8
Alarm : Ring alarm at Surveillance mode when movement is detected. User can select
one among 4 alarms.
9
Resolution : For NTSC: 320 x 240, 640 x 240
For PAL: 320 x 288, 640 x 288
10
Apply All : Applying to all the cameras with the same settings of current camera (ON/OFF)
TIP #7. Apply All (the same function in all other setup)
Applying to all the cameras with the same settings of current camera (ON/OFF)
However, the settings are not changed before you save the changes.
Selecting ‘Yes’ means saving all the settings
you have changed.
26
III. Setup Mode
3. Color Setup
1
2
3
4
5
6
1
Camera
2
BRIGHTNESS
3
CONTRAST
4
SATURATION
5
HUE
6
APPLY ALL : Applying to all the cameras with the same settings of current camera (ON/OFF)
27
III. Setup Mode
4. Motion Area Setup
1
2
4
3
[Motion Area Setup window]
1
Camera : to choose the camera for setting
2
Setup Motion Area : Example for motion area
Unselected Area
Unselected Area (with cursor)
Selected Area
Selected Area (with cursor)
3
Apply All : to apply the fixed setting to all cameras (ON/OFF)
4
Motion Area : to set up the motion area on the camera screen.
– Default Value : to set up the full motion area
(use the “REC” button and cursors for setting motion area)
28
III. Setup Mode
5. Schedule Setup
1
2
4
3
[Schedule Setup 화면]
1
Camera : to choose the camera for setting
2
Setup Schedule : example for setting the schedule
Record
Motion Record
Do Not Record
3
Apply All : to apply the fixed setting to all cameras (ON/OFF)
29
III. Setup Mode
TIP #8. For Schedule and Motion detecting Recording
Setup Schedule and Motion detecting recording
1. Set “Recording Status” to “Schedule” in the Camera Setup
2. Set “Record” or “Motion” of the selected camera in the Schedule Setup
3. Set motion area of the selected camera in the Motion Area Setup
[1. Set “Recording Status” to “Schedule”]
[2. Set schedule in the Schedule Setup]
[3. Set motion area in the Motion Area Setup]
if setting the schedule like the upper picture
for camera 01
- every Sunday : No recording
- every Monday : Always recording
- every Tuesday: recording when motion is
detected
30
III. Setup Mode
6. Network Setup
1
2
3
4
5
6
7
8
9
[Network Setup window]
1
Connection : to setup the network LAN / ADSL / DHCP
2
I P : IP Address
3
Net Mask / ADSL ID / Nothing :
LAN – to setup Net Mask
ADSL – to input ID password
DHCP – nothing applicable.
4
Gateway / ADSL Password / Nothing :
LAN – to setup Gateway
ADSL – to input ID Password
DHCP – nothing applicable
5
Port : For Network Client Application (Eye-Linker) – Default value : 5005
31
III. Setup Mode
6
Concurrent User : Concurrent number of user for Network Client Application
(Eye-Linker)
7
Picture Quality : to set up picture quality for Network (5 : the highest quality)
8
Ping Use : to confirm ping test to DVR AT Network
9
Bandwidth : to setup bandwidth for transmition
TIP #9.setting value for rebooting after Network setup
Rebooting should be done when any setting value was changed at Network Setup
[to confirm saving the changes]
[to confirm rebooting system]
32
III. Setup Mode
7. Sensor Setup
2
1
3
4
5
[Sensor Setup window]
1
Sensor : to choose the sensor to be set
2
Setting Up : N/O (Normal Open) or N/C (Normal Close) setting
3
Period of Time : to set the recording time
4
Storing : to select the camera for recording after sensor working
selected camera is distinguished by yellow color
5
Alarm : to set up the Alarm for sensor working
33
III. Setup Mode
8. Alarm Setup
2
1
3
[Alarm Setup window]
1
Alarm : to select Alarm
2
Setting Up : to setup N/O (Normal Open) or N/C (Normal Close)
3
Alarm lasting time : Period for Alarm working
34
III. Setup Mode
9. PTZ Control Mode
1
2
3
4
5
6
[PTZ window]
1
Camera : to select camera for PTZ control
2
PAN/TILT :to control PAN / TILT
3
ZOOM : to control Zoom in /Zoom out
4
FOCUS : to control Focus
5
LIGHT : to control Light
6
POWER : to control Power
TIP #10. setting value for rebooting after Network setup
Not to change the set value at PTZ mode
Only to control camera with PAN / TILT function
can be used for control
35
III. Setup Mode
10. Backup Mode
1
3
2
4
[Backup window]
1
2
To set up the date for back up
To confirm the date when data was recorded : the date of recording date can be
shown by red color
3
Backup : Back up the recorded file (by USB HDD)
( file format to be played back thru Eye-Linker after back up)
4
AVI Export : AVI format for back up (USB HDD)
(file format to be played back thru Windows Media Player
36
III. Setup Mode
1
5
3
2
6
4
[Backup window]
1
DVR System side : Left side for DVR System
2
Description of recorded file : File list of recording at selected date
3
sign for back up function : Channel Auto Switching for1, 4, 8, 9, 13
To start backing up
To start restoring
To delete the list selected
To select all list
4
Information status : Working status for back up
5
USB HDD side :
6
Description of file after finishing back up :
37
III. Setup Mode
TIP #11. How To Backup
How to back up (back up for AVI Export is under almost same way)
[to choose the date to be back up]
After selecting the list for back up
by “Enter” , working
Message for back up will be on,
then back up will be starting by
“Yes”
[select the list to be back up]
[back up is on going]
[finishing back up]
38
III. Setup Mode
11. System Administration
2
1
3
4
5
[System Administration window]
1
Setup Initializing : Back to the initial setup
Confirm : under initializing
Cancel
2
Log Backup : to back up the present System Log by USB HDD
Confirm
Cancel
39
III. Setup Mode
3
Upgrading Version : Application S/W Upgrade
Connect to Server : nothing applicable
Connect to Local : when upgrade for latest
version by USB, but can not working, it can be
back to old version
Connect to USB : upgrade S/W by USB Memory
4
Hard Disk Initializing : Initializing after deleting all recorded files
Confirm
Cancel
5
Status Windows : Status of each menu
40
III. Setup Mode
12. Search Mode
6
3
1
4
2
5
[Search Mode]
1
Normal : Normal Searching
2
Event : Searching for the recording data through the event from motion detecting or
sensor
3
Selecting date and time to search
4
Recording data status: The date marked in red color is the date that has recorded data
5
Displaying the time that has recorded data in the selected date
6
Displaying the camera status :
The camera has recorded data.
The camera doesn’t have recorded data.
41
III. Setup Mode
1
2
1
Monitor Area: Displaying recording data
2
Current Status
Playing
Stop (or pause)
FF x 1( x2, x4)
REW x 1( x2, x4)
Waiting
42
III. Setup Mode
TIP #12. “DIV” function in the Search Mode
Window can be divided by “DIV” button in the Search Mode.
TIP #13.
,
[16]
[9]
[full]
[4]
in the Search Mode
[Camera 1,2,3,4]
[Camera 5,6,7,8]
[Camera 13,14,15,16]
[Camera 9,10,11,12]
43
IV. DVR Application Troubleshooting Guide
# 1. No recording
Answer 1 : Verify if recording icon (
) is displayed in the Surveillance Mode
Answer 2 : Verify if “recording status” in Camera Setup is Do Not Record .
If so, change it to Full Record or Schedule
Answer 3 : Verify if the setting is “record”(
status is Schedule.
) in the Schedule Setup when recording
Answer 4 : Use “REC” function in the Surveillance Mode regardless of setup data of
each camera, if necessary.
# 2. Not recording in the Schedule mode
Answer 1 : Verify if “recording status” in the Camera Setup is Schedule.
If the recording status is Full Record or Do Not Record, it won’t work
with the schedule you setup.
# 3. Not recording in the motion detecting mode
Answer 1 : Verify if “recording status” in the Camera Setup is Schedule , if you want
to use motion detecting recoding mode.
Answer 2 : Verify if the setting is “motion” (
status is Schedule.
) in the Schedule setup when recording
44
IV. DVR Application Troubleshooting Guide
# 4. Stored data are deleted.
Answer 1 : When time is newly set, all of the stored data will be deleted. (Warning!)
Answer 2 : If you initialize HDD in the System Administration Setup, all date will be
deleted.
# 5. Not working with the control of the PTZ Camera
Answer 1 : Verify if “PTZ Type / ID” is correct in the Camera Setup
Manufacturer
ONIX
Model
CNB-PTZ102N
DONGYANG UNITECH
ORIENTAL SYSTEM
HONEYWELL
SAMSUNG
SAMSUNG TECHWIN
KODICOM
DRX-500
DVRX-1000
HSDN-251
HRX1000
SCC-641
SRX100B
SPD-1600
KRD-301/302
PELCO
PELCO-D
TRINUS
PT-100-200
LG
LPT_A100L
FILTEK
PT_102
[supporting PTZ]
45
IV. DVR Application Troubleshooting Guide
# 6. the screen of specific camera channel is OFF or the quality of image is poor.
Answer 1: Check if there is any problem with camera or camera adapter and
connection line.
# 7. No power to the DVR system
Answer 1 : Check if there is any problem with power, power cable and power connector.
# 8. Not showing Surveillance Mode after booting
Answer 1 : If it will not show Surveillance Mode after booting the system, the file system
of HDD can be damaged. Please contact the installed company, distributor or our head
office.
※ In case when a problem is not solved despite of the verification of above contents, contact
the installed company, distributor or our head office.
46
Chapter 3.
Eye-Linker User’s Guide
47
I. Features of Eye-Linker
General
Eye-Linker program is the DVR Network Client program to be installed on the Window OS
based PC which supports remote real time monitoring, controlling, searching, backup,
setup by accessing the several Linus OS DVRs connected each other thru Network
Real time monitoring for several DVRs thru Network
- Eye-Linker is for remote monitoring CCTV Video channel transmitted thru network by
accessing one of several Linux DVRs connected each other by network.
- Monitoring the selected cameras from DVRs connected by network.
Remote DVR System
Data input
Real time remote
monitoring for
selected cameras
Accessing DVR
Seoul
Pusan
Inchon
Pohang
Jeju
48
I. Features of Eye-Linker
Real time searching thru network for data in DVR system
Function for searching thru Eye-Linker program for video data at remote DVR system
- Network searching for the video data by month, day, time, camera at remote DVR thru
the same interface with DVR.
- Printing out the data after searching by JPEG.
- Function of image filtering and enlarging and reducing searched images.
To change the setup mode of remote DVR system
- Function to change auto channel switching, rebooting cycle setup key, basic setting
key of remote camera, each sensor key, etc
Network backup function for DVR system
Remote back up function thru eye linker by date, hour, time, camera at remote DVR
system of which file formats are Linux DVR system own format( LDV,IDX) and or AVI in
general.
49
II. Installation guide of Eye-Linker
1.System spec. to be recommended for Eye-Linker
Recommended spec.
-
CPU : Pentium III 800GHz or above
Memory : 256MB or above
HDD : 20MB or above
OS : Windows 2000 / XP / 2003
*Note*
Check your HDD space if you want to
backup files from remote DVRs
2. Installation steps for Eye-Linker
1) Run “Setup.exe”
To run the Eye-Linker
program by double click
the Setup.exe
50
II. Installation guide of Eye-Linker
2. Installation steps of Eye-Linker
2) Eye-Linker Setup
To choose the langague (Korean,
English, Japan)
1
2
3
4
51
II. Installation guide of Eye-Linker
3. To run Eye-Linker
To run Eye-Linker
-Double click the icon on Window screen.
Or
“C:\ProgramFiles\Leadtech\EyeLinker\EyeL
inker.exe
The message is to be on the
screen when initially execute
Eye-Linker program
It is not error so click the “OK”
[Initial mode]
52
III. User’s guide of Eye-Linker
Description of screen
1
2
3
4
6
5
1
Monitoring area : real time monitoring for maximum 16 screen of remote camera.
To click the right side mouse button
- Image filtering
- reducing/ enlarging
- real time storing
- to control the out side devices hooked into
DVR
Status for Camera connectivity of DVR.
[camera status]
53
III. User’s guide of Eye-Linker
Description of screen in detail
2
To management groups and lists for remote DVRs
: Add/Remove/Modify the groups and the lists of remote DVRs
Eye-Linker is designed for accessing to several remote DVRs at the same time.
The list of DVR groups can be chosen, then the information of these groups will be on the
screen.
TIP #1. How to list up the remote DVR
Add/Remove/Modify
Groups (Selection of
Group by double
click)
[Screen for Group Management]
-
Server name : Remote DVR name
Change Group : To choose the group of DVR to be added
Connection Type : TCP/IP, ISDN, Local
IP SERVER : When allocated IP by ADSL or DHCP,
inputting ID of DVR System , controlling the
finally changed IP of DVR, setting value to
connect the remote DVR by Eye-Linker
- IP : inputting fixed IP address
- port :Port number (Default: 5005)
- Folder : In case of connecting to Local
- Password: Password of the remote DVR (Default: 0000)
- Memo : Description for the remote DVR
- Server Status Description: To check the remote DVR
- Cameras for auto Connect: To choose cameras for showing
images automatically when you connect the remote DVR
- Save Folder: When back up for the remote DVR, the folder to
be store the backup data
54
III. User’s guide of Eye-Linker
Description of screen in detail
TIP #2. How to connect or disconnect the remote DVR
To connect remote DVR
To disconnect remote DVR
To choose DVR
Click “Connect” then showing the
video images of the remote DVR
55
III. User’s guide of Eye-Linker
Description of screen in detail
3
To control the Pan/Tilt/Zoom for cameras thru Eye-Linker
To control the direction of camera (The center button is
for controlling PTZ Light )
To set up camera Focus
To control Zoom In/Out
4
Divided screens for real time monitoring
1ch, 4ch, 9ch, 16ch
 automatic channel switching for 1, 4, 9, 16ch
 manually control
56
III. User’s guide of Eye-Linker
Description of screen in detail
To set up and finish Eye-Linker program
5
TIP 3. How to configure Eye-Linker
To finish the Eye-Linker
[Screen for EyeLinker configuration ]
-
Screen: To set up screens
Alarm : To set up warning and sensor
Connection: To set up connection
DVR IP Server : When using ADSL or DHCP
*Note*
To set up DVR IP server surely when IP
address is allocated by ADSL or DHCP.
Leadtech is now operating IP server
(Static IP: 211.105.46.29)
57
III. User’s guide of Eye-Linker
Description of screen in detail
6
Functions for controlling Camera/Sensor/Alarm, setup, search, backup in relation to real
time monitoring of remote DVR Systems
1
2
3
4
5
6
7
8
9
10
1
Information of currently connected DVR System (Model, Name, Version, HDD Used percent)
2
Status for camera of currently connected DVR system (To be changed by mouse click )
 connected
 disconnected
3
Status of sensor
4
Status of alarm
5
Set up : remote setting up the remote DVR system
To enter password
Gatheing configurations of the remote DVR
[ screen for setting of remote DVR ]
58
III. User’s guide of Eye-Linker
Description of screen in detail
TIP 4. To change the setting of remote DVR
General setting
[ Screen for general setting]
Camera setting
[ Screen for Camera setting ]
59
III. User’s guide of Eye-Linker
Description of screen in detail
TIP 4. To change the setting of remote DVR (Continued)
Schedule setting
[ screen of schedule setting ]
[ example of schedule setting ]
Motion area setting
[ example of motion area setting ]
[ screen of motion area setting ]
60
III. User’s guide of Eye-Linker
Description of screen in detail
TIP 4. To change the setting of remote DVR (Continued)
Sensor setting
[ screen of sensor ]
Alarm setting
*Note*
To remote set up the
configuration of remote DVR
is same way with DVR
[ screen of alarm ]
61
III. User’s guide of Eye-Linker
Description of screen in detail
6
Search: To search the recorded images of remote DVR system
Click “Search”
[ Search Mode]
Click “Search” on the Search mode to select the servers
(Remote DVRs)
Select the Remote DVR you want to search. When the
connection is “No” , click “Connect” then the remote DVR
will be connected to the PC.
1.
2.
3.
4.
Select the remote DVR you want to search택
Check if the connection is “YES”
Click “Select” on the DVR you select
Ready for searching
62
III. User’s guide of Eye-Linker
Description of screen in detail
TIP #5. How To Search
How to search remote DVR
When you select the DVR you want to search, it shows
dates and time which have recorded images
- Bold letter date : There are recorded images on the date
- Normal letter date : No recorded images on the date
- Green box(
- Blank box(
): There are recorded images on the hour
) : No recorded images on the time
Click to the time you want to search in the time table
Showing the recorded
images on the selected
time
Available to change searching speed in
5 levels
Searching Speed
Search Control
Brightness,
Contrast,
Color/Mono,
Saving recorded
images,
Print
Time Control
Dividing,
Channel Auto
Switching
63
III. User’s guide of Eye-Linker
Description of screen in detail
7
Back Up: Backup the recorded image files on remote DVR to the PC
Click “Backup” - Eye-Linker should be connected to the
remote DVR when you want to backup
- Check the date and time (Bold –
recorded images exist)
- The checked boxes on Select
Cam mean there are recorded
images on the cameras
- Select camera you want to
backup
Select download folder
Click “Backup Start” when you select the period for backup
[Backup Progressing]
[Backup Finished]
64
III. User’s guide of Eye-Linker
Description of screen in detail
8
Log View : Showing the logs of Eye Linker
Click “Log View”
Showing the log of “EyeLinker” Application
9
Check Water Mark : To Verify if the JPEG file from the DVR is modified or forged
Click “Check Watermark”
Select the file to verify
*Note*
You will know if the JPEG file is
modified after selecting the file.
65
III. User’s guide of Eye-Linker
Description of screen in detail
10
Avi Export: Backup the recorded image files which are converted to AVI format on
remote DVR to the PC. Please refer the “backup” part 7 in this manual.
Click “Avi Export”
66
IV. Eye-Linker Troubleshooting Guide
# 1. No connection to DVR
Answer 1 : Verify if network is working on the PC where the Eye-Linker is running.
Answer 2 : Check the network setup in the DVR and verify if DVR is connected to
network.
Answer 3 : Check if the remote DVR is working on.
# 2. Connected to remote DVR, but not showing any video images
Answer 1 : Edit the server you want to connect and select the cameras which are
automatically connected when you connect the DVR
Answer 2 : Check if the camera icon is on in the main screen of Eye-Linker
 connected to camera
 not connected to camera
67
IV. Eye-Linker Troubleshooting Guide
# 3. Unable to search for remote DVR
Answer 1 : Check if the PC connected to the DVR.
Answer 2 : Check if there are recorded images on the date you want to search.
Answer 3 : Check if the selected camera is on.
# 4. Unable to backup when you click the backup button
Answer 1 : Check if there are recorded files on the date you want to backup. Please
refer the Backup part again.
Answer 2 : Check if the checkbox of the camera you want to backup is checked.
If no checked on the “SelectCam”, the backup cannot be progressed.
# 5. Too slow to monitor in the display mode, the Search mode or to backup
Answer 1 : If you connect to many remote DVRs, the program can be slow because of the
network bandwidth.
Answer 2 : When the speed of backup is too slow, please turn off the current
monitoring cameras in the display mode.
Answer 3 : When the speed of searching is too slow, please turn off the current
monitoring cameras in the display mode.
68