Transcript Optical Fibre Communication

OPTICAL COMMUNICATIONS &
NETWORKING - AN OVERVIEW
By:
Mr. Gaurav Verma
Asst. Prof.
ECE
NIEC
Communication Systems
Basic Blocks
• Three basic components
• Source and Transmitter
• Destinations and Receiver
• Communication channel
(medium)
• Communication channel
• Wired
• Wireless
• Glass
• Water and or materials
Coverage and Topology
• Coverage (public network)
• LAN
• MAN
• WAN
• Topology
• Bus
• Ring
• Mesh
• Star
Changing Service Landscape
• Network characteristics
• Full redundancy
• Fast restoration
• High availability (99.999 %)
• Low latency
• High bandwidth
• Dynamic allocation and high bandwidth efficiency
• Support various services
• More providers and equipment builders (due to Deregulation of
the telecom industry)
• Providers are expected to provide more services at higher
capacity at lower prices!
• A positive feedback business model!
• Need for high capacity network
• More users
Service Types
• Two basic service types (switching technologies)
• Connection-oriented
• Connectionless
• Connection-oriented
• Based on circuit switching (setup, connect, tear-down)
• Example: Public Switching Telephone Network (PSTN)
• Originally only supported voice
• Not good for bursty traffic
• Connectionless
• Based on sending datagrams
• Examples: Packet, massage, burst switching
• Improves bandwidth and network utilization
Multiplexing
• Transmitting several signals over a single communications
channel
• Multiplexing technologies
• Frequency Division Multiplexing (modulating data into different carrier
frequencies)
• Wavelength Division Multiplexing
• Time division Multiplexing (dividing available time among various
signals)
• Statistical Multiplexing (dynamic allocation of time spaces depending
on the traffic pattern)
• Statistical Multiplexing
• Requires buffering resulting in variable delay
• Many packets will have to be buffered
• Packets will have to be delayed
• Some packets may be lost
• Guarantee of Service (QoS)
Multiplexing
Optical Fiber
• Allowing transmission of information using pulses of light
• Advantages
• High bandwidth
• Low noise
• Low interference (electromagnetic)
• Optical fiber installation
• Measured in fiber sheath-miles (or fiber miles)
•
Example: we install 3 fiber cable within 10 mile long route;
each fiber cable has 20 fibers  we have 600 fiber miles 30
cables
• Currently more than 1.5 billion kilometers of optical fiber is
deployed around the world [1]
• The circumference of earth is 40,000 Km!
[1] http://www.corning.com/opticalfiber/innovation/futureoffiber/index.aspx
Evolution of Optical Networks –
First Generation
• Started in 1980
• Limited to fiber optic transmission systems – the rest of
the system was electrical
• Thus, the electronic was the major bottleneck!
• The received optical data had to be dropped and then transmitted –
this was a point-to-point system
• Example: Synchronous Optical Network (SONET) and
Synchronous Digital Hierarchy (SDH), Fiber Distributed Data
Interface (FDDI), Fiber Channel
• These systems where based on Optical TDM (10Gb/s and 40Gb/s)
• Higher capacity systems were build using WDM technology (1
Tb/s) – remember a single phone line is only 60 Kb/s!)
Evolution of Optical Networks –
Second Generation
WADM
• Incoming optical signals could be
switched in optical domain (optical
switching)
• No longer limited to point-to-point
• Underlying technologies included
• Optical Add-Drop Multiplexers (OADM)
• Optical crossconnets (OXC)
• Optical line terminals (OLT)
• Wavelength Add/Drop Multiplexer (WADM)
• Dense WDM (DWDM)
• Examples
• FTTH, FTTC, ROADM
OXC
Evolution of Optical Networks –
Third Generation
• All optical packet switching
• All packets are processed in optical domain
• Transparent to the service
• Handle any arbitrary bit rate
• Underlying technologies
• Optical buffering!
• Fast switching
So far, no optical networks have been available!
Optical Networking
Comparing Different Optical Nodes
Optical Packet Switching
13
Layering Model
Open Systems
Interconnection
(OSI) SevenLayer Reference
Model
The layering Model for the IP
Protocol Suites and Layering Models
• Physical Layer (Layer 1)
• specify details about the underlying transmission medium and
hardware
• all specifications related to electrical properties, radio frequencies,
and signals belong in layer 1
• Network Interface (or Data Link) Layer (Layer 2)
• Network (physical) addresses
• maximum packet size that a network can support
• protocols used to access the underlying medium
14
Protocol Suites and Layering Models
• Internet Layer (Layer 3)
• protocols specifying communication across the Internet & routing
specifications (spanning multiple interconnected networks)
• Logical addressing and path determination
• Transport Layer (Layer 4)
• Includes specifications on
• controlling the maximum rate a receiver can accept data (flow control)
• mechanisms to avoid network congestion
• techniques to insure that all data is received in the correct order
Remember: Each layer contains its own specifications & protocols!
15
Protocol Suites and Layering Models
• Application Layer (Layer 5)
• specify how a pair of applications interact when they communicate
• specify details about
• the meaning of messages that applications can exchange
• the procedures to be followed to execute the application
• Some examples of network applications in layer 5
• email exchange
• file transfer
• web browsing
• telephone services
• and video teleconferencing
16
17
How Data Passes Through Layers
Each computer has a
layered protocols
IP over ATM over SONET
IP over SONET
IP over WDM