Transcript Core i7 - ItProjects For You

Welcome To Seminar On
INTEL CORE i7
Presented By:
1
INTRODUCTION
• A Central Processing Unit (CPU), or sometimes just called
processor, is a description of a class of logic machines that can
execute computer programs.
• Intel Core i7 is a family of three Intel desktop processors, the
first processors released using the Intel Nehalem micro
architecture and the successor to the Intel Core 2 family. All
three models are quad-core processors.
2
BASICS
• In computer architecture, 32-bit integers, memory addresses, or
other data units are those that are at most 32 bits (4 octets) wide.
Hence, 32-bit CPU and ALU architectures are those that are
based on registers, address buses, or data buses of that size.
• In computer architecture, 64-bit integers, memory addresses, or
other data units are those that are at most 64 bits (8 octets) wide.
Also, 64-bit CPU and ALU architectures are those that are based
on registers, address buses, or data buses of that size.
• In computer engineering, microarchitecture is a description of
the electrical circuitry of a computer, central processing unit, or
digital signal processor that is sufficient for completely
describing the operation of the hardware.
3
FEATURES
1.


SOCKET: The Socket is a new LGA1366(Socket B) and is incompatible
with the previous versions:
LGA refers to Land Grid Array, a new type of socket for the latest range of
processors. The LGA is used as a physical interface for microprocessors of
the Intel Pentium 4, Intel Xeon, Intel Core 2 and AMD Opteron families.
Unlike the pin grid array (PGA) interface found on most AMD and older
Intel processors, there are no pins on the chip; in place of the pins are pads
of bare gold-plated copper that touch pins on the motherboard.
Intel supposedly decided to switch to an LGA socket because it provides a
larger contact point, allowing, for example, higher clock frequencies. The
LGA setup provides higher pin densities, allowing more power contacts
and thus a more stable power supply to the chip.
4
2. ON-DIE MEMORY CONTROLLER: The memory is directly connected to
the processor.
 Three channel memory: each channel can support one or two DDR3 RAM’s.
Motherboards for Core i7 have four or six RAM slots.
 Supports DDR3
•
DDR3 RAM (double-data-rate three random access memory ) is a random
access memory technology used for high speed storage of the working data in
the computer.
•
The benefit of DDR3 is the ability to run its I/O bus at four times the speed of
the memory cells it contains, thus enabling faster bus speeds and higher peak
throughput than earlier memory technologies.
•
The DDR3 standard allows for chip capacities of 512 megabits to 8 gigabits,
effectively enabling a maximum memory module size of 16 gigabytes.
•
There is a significant reduction in power consumption. It needs only 1.5V
compared to 1.8V for DDR2.
7
8
3.
Quick Path Interconnect:T he front side bus is replaced by Quick Path
interconnect. Motherboards must use a chipset that supports Quick Path.

the Front Side Bus (FSB) is the bus that carries data between the CPU and the
north bridge.

Front side buses serve as a connection between the CPU and the rest of the
hardware via a so-called chipset. This chipset is usually divided in a north
bridge and a south bridge part, and is the connection point for all other buses
in the system
Pros: FSB architecture is an aging technology. High flexibility , low cost and
no theoretical limit to the number of CPUs that can be placed on a FSB.
Cons: In recent years this has been breaking down with increasing use of
individual point-to-point buses (see Hyper Transport and Quick Path). The
front side bus has been criticized by AMD as being an old and slow
technology that bottlenecks today's computer systems.
9

The Intel QuickPath Interconnect (QPI) is a point-to-point processor
interconnect developed by Intel to compete with HyperTransport. It will
replace the Front Side Bus (FSB) for Desktop.

The speed of data transfer is 25.6 Gbps, almost double that of FSB.
10
4. Cache Memory
 32 KB L1 instruction and 32 KB L1 data cache
per core.
 256 KB L2 cache (combined instruction and
data) per core.
 8 MB L3 (combined instruction and data)
shared by all cores.
11
(a). Re-implemented Hyper-threading.

Each of the four cores can process up to two threads simultaneously, so the
processor appears to the OS as eight CPUs.

Hyper-threading (officially termed Hyper-Threading Technology or HTT)
is an Intel technology used to improve parallelization of computations
performed on PC microprocessors.
(b). 781M transistors for the quad core version.
(c ). Sophisticated power management can place an unused core in a zero-power
mode.
5.
Support for SSE4.2 & SSE4.1 instruction sets.

SSE4 is an instruction set used in the Intel Core microarchitecture and AMD.

Intel SSE4 consists of 54 instructions. A subset consisting of 47 instructions,
referred to as SSE4.1. Additionally, SSE4.2, a second subset consisting of the
7 remaining instructions, will first be available in Core i7.
12
 The processor has a Thermal Design Power of 130W and will slow
itself down if the power is exceeded.
 The Thermal Design Power (TDP) (sometimes called Thermal
Design Point) represents the maximum amount of power the cooling
system in a computer is required to dissipate.
 The cost per piece is Rs. 47,000 in lots of 1000 units.
13
6. Overclocking : Overclocking is the process of forcing a computer
component to run at a higher clock rate (more clock cycles per second)
than it was designed for or was designated by the manufacturer, usually
practiced by personal computer enthusiasts in order to increase the
performance of their computers.
 The idea is simple by varying the electrical and physical characteristics
of computing systems.
 The first consideration is to ensure that the component is supplied with
adequate power to operate at the new speed. However, supplying the
power with improper settings or applying excessive voltage can
permanently damage a component.
15




A chipset is a group of integrated circuits, or chips, that are designed
to work together, and are usually marketed as a single product.
In personal computers based on Intel Pentium-class microprocessors,
the term often refers to a specific pair of chips on the motherboard:
the northbridge and the southbridge.
The northbridge links the CPU to very high-speed devices,
especially main memory and graphics controllers, and the
southbridge connects to lower-speed peripheral buses (such as PCI
or ISA).
In many modern chipsets, the southbridge actually contains some
on-chip integrated peripherals, such as Ethernet, USB, and audio
devices. A chipset is usually designed to work with a specific family
of microprocessors. Because it controls communications between the
processor and external devices, the chipset plays a crucial role in
determining system performance.
16
17
 The northbridge typically handles communications among the CPU, RAM,
AGP or PCI Express, and the southbridge. Some northbridges also contain
integrated video controllers, also known as a Graphics and Memory
Controller Hub (GMCH) in Intel systems.
 The southbridge is a chip that implements the "slower" capabilities of the
motherboard. Because the southbridge is further removed from the CPU, it is
given responsibility for the slower devices on a typical microcomputer.
18





The Intel X58 (codenamed Tylersburg) is an Intel chip designed to
connect Intel processors with Intel QuickPath Interconnect (QPI)
interface to peripheral devices. Supported processors implement
the Nehalem micro architecture and therefore have an integrated
memory controller (IMC), so the X58 does not have a memory
interface.
Except for the lack of a memory interface, the X58 is similar to the
traditional Northbridge.
Communicates with the processor via the high speed QPI, it
communicates with the Southbridge via DMI, and it
communicates with high speed peripherals via PCI-E.
The X58 is not a memory controller hub (MCH).
X58 QuickPath Interconnect port has 20 lanes.
19



Unlike the FSB, QPI is a point-to-point interface and supports not
only processor-chipset interface, but also processor-to-processor
connection and chip-to-chip connection.
The X58 has two QPIs and can directly connect to two processors on
a multi-socket motherboard or form a ring-like connection :
(1st processor - x58 - x58 - 2nd processor - 1st
processor)
I/O Controller Hub (ICH), also known as Intel 82801, is an Intel
microchip used as southbridge on motherboards with Intel chipsets
(Intel Hub Architecture). As with any other southbridge, the ICH is
used to connect and control peripheral devices.
20


High end motherboard intended mainly for the gamers with the
best features of graphics and overclocking.
Provides ultra-realistic graphics and high-impact, professional
gaming performance.
21
22




In a test performed on a leaked hardware, the core i7
outperformed the currently fastest core2 extreme processor.
It has got the advantages of high performance, highly
overclockable, quite cooling and power efficient.
Some of the disadvantages include the requirement of newer
motherboards, sensitive to higher voltage.
The technology keeps on improving as the need for faster and
high end applications increases. The 8 core version is about to be
released soon.
23





www.intel.com/pressroom/archive/releases/2007032
8fact.htm
www.wikipedia.org/Intel Core i7.htm
http://download.intel.com/design/processor/applnots
/320354.pdf?iid=tech_tb+paper
www.pdf-search-engine.com
www.Anandtech.com
24
25
26