Transcript ComfortG2
Comfort II Whats New (updated Jan 2008) Two-Piece Design • Consists of CPU Board and DSP Board, joined by a 28 way connector • CPU Board has Inputs, Outputs, Siren, Strobe, KA/KB, 12V etc for Alarm functions • DSP Board has Tel In, Tel Out, Voice, Mic, power supply for Voice and Dialing functions Slave • New Generation Slave will be the CPU Board with Slave firmware • Power Supply board will replace the DSP board connected to the Slave Flash Upgrades • Flash Firmware upgrade is available as Plug-in Module (MPU01) • Comfort II with Flash MPU plug-in (see picture) can be upgraded by firmware download via Comfigurator 2.2.x. This requires new UCM05 • In 2008, Comfort II PCB will come with built-in Flash firmware and will not require MPU01 UCM05 • New UCM05 is able to download new firmware upgrades to Comfort II with builtin Flash or Flash MPU. Requires Comfigurator 2.2.x • Programming Cable connects UCM05 with Comfort II, Slave II or UCM05/EIB/CBUS to be upgraded • IR Learning is standard feature Local Expansion Modules • LEM01-M2 or LEM02-M2 or LEM03-M2 will plug on top of CPU or Slave Board • Output module will be plugged into LEM and can be removed Battery Protection • Battery protection function is built in. BPM01 Module not required. • Prevents over-discharge of battery • Current limits charging current to a low battery Piggyback Modules • Ringer Module RGR04 can be plugged in • LEM can be plugged in • Output Module can be plugged in. This allows damaged Outputs to be replaced without any downtime • Firmware upgrades can be plugged in • Saves space in the enclosure Isolation • Comfort circuitry is isolated from earth. Plastic standoffs for mounting PCB • Provides better protection from lighting induced surges. • All Inputs and Outputs have been tested to 4kV surge. • Improved Telephone line protection Testing/Approvals • EMC compatibility for US and European standards • Safety testing for CE Mark • PSTN standards compliance to US, European and Australian standards • Tested to extended surge voltages (4 KV) compared to European standards Full Duplex Intercom • Full Duplex Intercom between Tel and KP/DP and between KP and DP • New KP04 versions needed with better acoustic isolation • KP03 and DP03 replaces KP01/02 and DP01 • DP and KP have separate Mic/Voice connections Various Improvements • Better Busy Tone detection during recording, voice menu, Intercom • Automatic Gain Control (AGC) during recording Vocabulary Tool • VoiceProc software allows customisation of wordlists for specific applications and development of vocabularies in other languages • VoicePlay allows sentences to be heard in compressed and original form System Voltage • CPU and DSP circuitry operates at 3V instead of 5V. • This means analog input voltage is 0 to 3V Other New Features • Conditional Branch Instructions will improve if/Then code generation • 32 Time Programs • 16 Reminder Messages • Say Word Action • 64 User Timers Compatibility • All current external modules on RS485 bus will remain compatible (Slaves, RIOS, Keypads, Door Stations, UCMs) • KP01, KP02, KP04, DP01 will remain compatible but with poor performance for full duplex intercom. Upgrade to KP03, KP04/X, DP03 is recommended Comfort I v Comfort II • Comfort I Ultra – – – – 8 reminders 16 time programs 16 User timers One-way intercom ½ duplex between KP and DP – File System 24 – Firmware upgrade via change of U1 IC • Comfort II Ultra – – – – 16 reminders 32 time programs 64 User timers Two-way intercom full duplex between KP and DP – File System 34 – Firmware upgrade via download to MPU01 or Flash firmware