Transcript Plasma PowerPoint

ESAB Welding & Cutting Products
PLASMA
Cutting & Gouging
ESAB 1904-2004
A CENTURY OF INNOVATION
THREE CUTTING METHODS
MECHANICAL
Saw, Drill,
Punch, Shear
CHEMICAL
Oxy-Fuel
THERMAL
Plasma, Laser,
Electron Beam
WHAT IS A PLASMA ARC?
• PLASMA - a fluid part of the blood
• PLASMA - an ionized gas (Air)
• When a gas is heated above 17,000 0F,
electrons are free to move. The gas
conducts electricity
THE PLASMA SYSTEM
AIR
REGULATOR /
FILTER
POWER
SOURCE/
CONTROL
Work Clamp
Torch
SPARE
PARTS KIT
GTAW (TIG) ARC
TUNGSTEN ELECTRODE
GAS CUP
OPEN ARC
SHIELDING GAS
WELD PUDDLE
GTAW (TIG) ARC = OPEN ARC
• Excellent heat source - 35,000 0F
• Arc lacks intensity or focus
• Arc lacks needed velocity to blow molten
metal from kerf
• Excellent for welding - unsuitable for cutting
or gouging
PLASMA = CONSTRICTED ARC
• Constriction
focuses the arc
• Increases arc
temperature
• Increases arc
voltage
• Flow of gas
controls plasma
velocity
TEMPERATURE DIFFERENCE
THERMAL SOURCE REQUIREMENTS
• High temperature - to melt metal
• Highly focused and intense source - to make a
narrow kerf
• High velocity gas stream - to blow the molten
metal from the kerf
KERF
• The narrow cut or void left by the
cutting process
END VIEW OF A TYPICAL PLASMA KERF
DROSS FORMATION
• The molten metal that was blown through the
kerf and sticks (welds itself) to the bottom edge
of the plate
• Low travel speed - easily removed
• High travel speed - Very difficult to remove
HIGH SPEED
LOW SPEED
CONVENTIONAL TORCH
DUAL FLOW TORCH
HIGH FREQUENCY STARTING
• High Frequency (HF) starting
requires an arc of about
10,000 volt at 1.5 MHz
• This high voltage arc jumps
the electrode to nozzle gap
and ionizes a path through
the gas
• When the cutting tip touches
the work piece the main arc
flows through this ionized
path
• The PT-31XL torch uses a
HF start
High Frequency
PLASMA
GAS (air)
IONIZED
GAS
PILOT ARC STARTING
• Pilot arc torches also require High
Frequency to ionize the gas in the
torch
• A low current (pilot arc) flows
through the HF path. The plasma
gas(air) blows this arc through the
nozzle
• When the pilot arc comes close
enough to the work piece the main
cutting arc transfers and takes the
place of the pilot arc
• Advantage - The cutting tip does
not have to touch the work piece
resulting in longer life
PLASMA
GAS
PILOT ARC
BRIGHT ZONE
HOT PLASMA
(CONDUCTIVE)
The PT-25, 26, 27 and PT-121
torches
use a PILOT ARC start.
PILOT ARC
• After two seconds of *preflow the HF energizes and the
PILOT ARC fires
(Click on image to play video)
* Preflow: The gas (air) flow prior to the High Frequency and Pilot Arc
OPERATING TIPS
The Do's and Don'ts
PT-25 / PT-26 / PT-27
TORCH SETUP
• With the POWER turned "OFF" - Check the torch
consumables for wear and proper assembly
AIR SETUP
• With the POWER turned "ON" and the AIR CHECK
switch in the "ON" position - set the air pressure per
the instruction literature (usually 65-75 psi.)
AIR SUPPLY
• Contaminated air supply will shorten electrode and
nozzle life.
• Check filter bowl for water or oil.
• An additional air filter/dryer may be necessary. Available
for less than $100.
WHEN TO CHANGE CONSUMABLES
• Cut speed and quality will deteriorate when the
nozzle (tip) or electrode become damaged.
TECHNIQUE
(Click on image to play video)
PLASMA TORCH ARC STARTING
PILOT ARC - START
PLACE TIP 1/4” ABOVE
PLATE - DO NOT TOUCH
PLATE !
PT-25, 26, 27
EDGE STARTS
• Always start at the edge With some metal under the tip
PT-34, PT-31XL
PT-25, PT-26 or PT-27
EDGE STARTS
• NEVER PLACE THE TIP OVER THE EDGE WITHOUT METAL UNDER THE TIP
PT-31XL, PT-34
PT-25, 26 or PT-27
PIERCE STARTS
• Never pierce with the torch in the vertical
position and the tip touching the plate
PT-25
PT-26 / PT-27
PIERCE STARTS
ANGLE TORCH TO BLOW MOLTEN METAL
AWAY FROM CUTTING TIP AND TORCH HEAD
Pierce Starts
• Angle torch to blow molten metal away from cutting
tip and torch head
• NEVER pierce with the torch in the vertical position
(Click on image to play video)
DRAG CUTTING
• Hold the tip against a straight edge
• Follow a template for irregular shapes
(Click on image to play video)
DRAG CUTTING TECHNIQUE
• You can drag the PT-31XL or PT-34 torch on the plate
• Hold the tip against a straight edge
• Follow a template for irregular shapes
CUTTING WITH A CONSTANT STAND OFF
(Click on image to play video)
• Hold the torch nozzle
approximately 5mm
above the plate
• Torch angled of 5o to
15o to plate surface
DRAG CUTTING WITH STAND OFF GUIDE
• Use stand off guide to optimize consumable life
(Click on image to play video)
PLASMA ARC GOUGING
PLASMA GOUGES
AL
CS
SS
Plasma Gouging
• Torch angled 30o to plate surface
• Arc washes the surface instead of cutting
(Click on image to play video)
AL
CS
SS
PLASMA CUTTING vs GOUGING
Plasma cutting
• Torch held 90o to plate
surface
• Smaller orifice produces
highly constricted arc
• High arc force
produces cut
Plasma gouging
• Torch angled 30o to plate
surface
• Larger orifice produces
softer wider arc
• Arc washes the surface
instead of cutting
PLASMA GOUGING vs CARBON ARC GOUGING
•
•
•
•
Lower fume levels
Lower noise levels
High quality surface
Lower cost
ESAB Welding & Cutting Products
THE END
Thank You
ESAB 1904-2004
A CENTURY OF INNOVATION