Transcript Wireless Topologies

© 2003, Cisco Systems, Inc. All rights
© 2003,
reserved.
Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-1
1
Module 4
Wireless Radio Technology
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-2
Overview
This module cover WLAN Topologies and
components. This will provide prerequisite
knowledge, before the network design and
deployment phases are introduced. Client
adapters, AP and bridges are discussed. After
examining the different types of wireless
topologies, channel setup and usage is
discussed. Finally, a number of sample
configurations are introduced.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-3
Learning Objectives
• Understand various WLAN topologies which
can be created.
• Understand WLAN Channel setup
• Explain the association, de-association and reassociation process
• Explain the various bridge and AP modes and
topologies
• Understand VLAN, QoS, and Proxy Mobile IP
WLAN technologies
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-4
Key terms
• Repeater
• VLAN
• Roaming
• Redundancy
• Load Balancing
• Hot Standby
• Scalability
• Multirate
• QoS
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-5
WLAN Topologies
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-6
Wireless LAN Implementations
Wireless Networking
Mobile user connectivity
Wireless Bridging
LAN-to-LAN connectivity
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-7
Typical WLAN Topologies
Wireless “Cell”
Channel 1
Wireless “Cell”
Channel 6
Access Point
Wireless Clients
© 2003, Cisco Systems, Inc. All rights reserved.
Overlapping
10-15%
LAN Backbone
Access Point
Wireless Clients
FWL 1.0—4-8
Wireless repeater
Wireless Repeater “Cell”
Channel 1
LAN Backbone
Channel 1
Access Point
Access Point
Wireless Clients
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-9
Hot Standby
LAN Backbone
Monitored
Access Point
Standby
Access Point
Wireless Clients
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-10
Alternative Peer-to-Peer Topology
Peer-to-Peer Configuration
(ad hoc mode)
Wireless “Cell”
Wireless Clients
Internet
Connection
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-11
Roaming
• Factors need to be considered when designing a
WLAN with seamless roaming capabilities for
devices that are powered on while moving from one
point to another:
•Coverage must be sufficient for the entire path.
•A consistent IP address should be available
throughout the entire path.
• Clients will associate with initial AP. Re-association
will occur as the AP strength weakens, and a new AP
is found for association.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-12
Association
If more than one AP replies, the client will
associate based on the information returned.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-13
Re-association
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-14
Scalability
• Scalability is the ability to locate more than one
access point in the same area. This will increase
the available bandwidth of that area for all users
local to that access point.
• Depending on the number and speed of the
available channels, cells can achieve higher data
rates.
•With 802.11b, there are 3 separate, 11-Mbps channels,
yielding up to a theoretical 33 Mbps per cell. User
devices operate at a maximum theoretical value of
11Mbps, since they can only connect to one AP at any
given time.
•802.11a has 8 54 Mbps channels, yielding a theoretical
432 Mbps.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-15
Channel Setup
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-16
Overview
• There are two critical steps for a good
WLAN deployment:
•Determine number and placement of access
points or bridges. Very few gaps in the
coverage should be left. These gaps are
essentially dead air and the client will lack
connectivity in these locations.
•Map out the channel assignments: There
should be as little overlap as possible between
channels that use the same frequency.
• Remember: 802.11b has 3 channels,
802.11a has 8 channels.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-17
Access point coverage & comparison
• As a client moves away from the AP, the
transmission signals between the client and
AP weaken.
• Rather than decreasing reliability, the AP
shifts to a slower data rate, which gives more
accurate data transfer. This is called data rate
or multi-rate shifting.
• This happens without losing the connection,
and without any interaction from the user.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-18
Rate Shifting
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-19
Multi-rate implementation
• The distance from an access point effects the available
bandwidth. Multi-rate technology allows a step down in
bandwidth to gain greater coverage distances.
• If 11Mbps is required everywhere, the access points would
need to be relocated, so that only the 11-Mbps circles are
touching each other, with some overlap.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-20
Bridge Topologies
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-21
Root modes
• Access points and bridges have two
different root modes, in which to operate
the following:
•Root = ON: The bridge or AP is a root. If it is a
bridge, then it is called the master bridge.
•Root = OFF: The bridge or AP is not a root.
• This setting controls when associations
and communication between different
infrastructure devices will be allowed.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-22
Bridge Root Modes
Root=ON
•Accepts association and
communication with
clients and repeaters
•Will not communicate
with other Root=On
devices.
Root=OFF
•Associates and
communicates with
Root=ON master bridge
only.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-23
Access Point Root Modes
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-24
Point-To-Point Wireless Bridging
Point-to-point wireless
bridges, two LANs can be
located up to 25 miles apart.
Antennas must have line-ofsite. Obstacles cause
communication problems.
One bridge to Root = ON and
the other Root = OFF.
With Cisco IOS, it is
possible to use Fast
Etherchannel or
multi-link trunking, to
aggregate up to three
bridges together,
yielding 33 Mbps.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-25
Point-to-multipoint configuration
All the LANs appear as a
single segment. Traffic
from one remote site to
another will be sent to
the main site and then
forwarded to the other
remote site. Remote
sites cannot
communicate directly
with one another.
•Omni directional antenna used at the main site. Directional
antennas at the remote sites.
•Line of sight must be maintained between remote and main
sites.
•Main bridge Root = ON and all other bridges Root = OFF/
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-26
Distance limitations
• For distances  1 mile, the workgroup
bridge and AP can be used.
• For  1 mile, bridges should be used.
• Using an AP or WGB for greater distances
is unreliable due to timing constraints.
• Cisco bridge products have a timing
parameter that can be adjusted (violating
802.11 standards), to support distances
over 1 mile.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-27
Bandwidth
• The maximum aggregate date rate can
only be achieved in a cell, if all remote
units are operating at the highest rate. The
number of users that can be supported by
a single AP is dependent upon the
bandwidth and the application needs.
• Typical throughput will be lower than
maximum data rate for all devices.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-28
Sample Topologies
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-29
Ad Hoc Topology
• Peer-to-Peer (Ad Hoc)
Topology (IBSS)
•Can consist of 2 or
more PCs with
wireless network
adapters.
•Sometimes called an
Independent BSS.
•Limited range.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-30
Basic Infrastructure Topology (BSS)
• Building block of an
802.11 LAN that covers a
single cell
• When a device moves
out of its BSS, it can no
longer communicate
with other members of
the BSS.
• Uses infrastructure
mode, requires an
access point (AP).
•All stations communicate through the AP, not directly
with peers.
•A BSS has one service set ID (SSID).
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-31
Extended Infrastructure Topology (ESS)
• 2 or more BSSs that
are connected by a
common distribution
system
• Allows the creation of
a wireless network of
arbitrary size and
complexity.
• All packets in an ESS
must go through one
of the APs.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-32
Base Station-Dial-up
Designed for the small office/home office (SOHO).
Gives telecommuters, SOHOs, and home users
the convenience of wireless connectivity.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-33
Base Station—DSL
• Offers support for a
Cable or DSL modem
• Will only support
wireless clients.
• DHCP functionality is
supported, but access to
the wired network is not
provided, as the
Ethernet port must be
used to connect to the
Cable/DSL modem.
• Support for PPP over
Ethernet.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-34
Campus Topologies
• Serves as an access system that
incorporates complete mobility.
• Allows users to access information from
unwired places outdoors, in dining halls
or informal study spaces, from classroom
seats and, even, the athletic fields
• Not a replacement for the wired LAN.
• Provides networking in hard-to-reach
and/or temporary locations.
• Allows users to work together in common
areas will maintaining network access.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-35
Campus topologies
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-36
WLAN addition to AVVID
• WLANs are part of Cisco’s Architecture for Voice,
Video, and Integrated Data (AVVID). AVVID provides
the roadmap for combining business and
technology strategies into one cohesive model.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-37
VLAN, QoS and Proxy Mobile IP
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-38
VLAN features
• Security—separating systems that have sensitive data
from the rest of the network.
• Departments/job types—VLANs set up for departments
that are heavy network users or a VLAN that is dedicated
to specific types of employees.
• Broadcasts/Traffic flow—Since a principle element of a
VLAN is the fact that it does not pass broadcast traffic to
nodes that are not part of the VLAN, it automatically
reduces broadcasts.
• WLANs can now fit nicely into the larger network because
VLANs have been enabled on the Access Points. This
allows WLAN users to roam from access point to access
point maintaining connectivity to the proper VLAN.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-39
VLANs in the Wireless network
• VLAN 100 allows
guest access.
• VLAN 101
supports barcode
scanners with
WEP security.
• VLAN 102
supports 802.1x
EAP security.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-40
Quality of Service (QoS) feature
• Used for time critical traffic (voice, video)
• Current support for downstream QoS
only: AP to client. (802.11q)
• Upstream will be supported with firmware
upgrade. (802.11e QoS)
• 802.11e includes:
•Enhanced Distributed Coordination Function
(eDCF), which is responsible for prioritization.
•Transmission Opportunity (TXOP), which is
responsible for transmission control.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-41
Enhanced Distributed Coordination Function
• eDCF allows higher priority traffic first
access to the WLAN media.
• With QoS, instead of backing off for a
random period of time, high priority
packets will back off for reduced amount
of time.
• The higher priority traffic passes through
the AP faster than packets with lower
priority.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-42
Transmission Opportunity
• Transmission Opportunity (TXOP) is for environments
that have a large amount of WLAN traffic.
• High priority packets will only wait a few seconds to
retransmit.
• If the traffic volume is still high, the high priority
packet will continue to resend again and again.
• TXOP will always reserve a place in line for the high
priority packets by reserving the first few seconds for
high priority packets, guaranteeing priority packet
handling.
• If there is not a high priority packet in the queue, the
AP processes the next packet in line.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-43
Proxy mobile IP: Layer 2 Roaming/IAPP
• 802.11 does not define how APs track mobile
users or how APs negotiate a handoff from one
AP to the next (roaming).
• Several companies have introduced proprietary
Inter-Access Point Protocols (IAPP) to support
roaming.
• IAPP accomplishes roaming within a subnet.
However, it does not address how the wireless
system tracks users moving from one subnet to
another when the same session must be
maintained, as in the case of voice calls.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-44
Layer 3 Roaming / Mobile IP
Where wireless is
being deployed
across multiple
subnets, there
are options to
achieve
seamless
roaming.
Wireless client adapters can contain proprietary
client IP stacks that understand mobility and allow
roaming between subnets. All mobile users on the
network must have special software installed.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-45
Layer 3 Roaming / Proxy Mobile IP
• The wireless infrastructure contains the
intelligence to allow user roaming.
• Cisco’s Proxy Mobile IP is designed for use in
complex network environments. As the wireless
device leaves an area and enters the next, the new
AP queries the device for its home agent.
• After the home agent has been located, packet
forwarding is established automatically between
the new and old APs to ensure the device can
transparently exchange data.
• Does not require installation of client-side
software; however both the router and the APs
must be configured to support Proxy IP.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-46
Proxy Mobile IP
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-47
Summary
• Many WLAN topologies which can be created.
• Many WLAN Channels are available
• Various processes are involved between the
client and AP
• Various bridge and AP modes are available
• VLAN, QoS, and Proxy Mobile IP WLAN
technologies provide enterprise level services.
© 2003, Cisco Systems, Inc. All rights reserved.
FWL 1.0—4-48
© 2003, Cisco Systems, Inc. All rights reserved.
49