Transcript MSPowerPoint

Institutional Repository
Workshop
1 – 3 April 2009
Presented by Leonard Daniels
1
Overview
DSpace in a VMware Image
This is an easy way to get DSpace 1.5 up and running with very little
effort. DSpace 1.5 has been pre-loaded on this vmware image. Only a
few amendments are required to get your own DSpace running.
Chapter 1
Get your Vmware player or Vmware server running. Once installed,
import and start the vmware image of DSpace from the hard drive
(provided on DVDs).
Chapter 2
Configure your server setting to your network requirements. Continue to
edit your DSpace settings to suit your setup.
2
Pre-Requisites
Hardware Configuration
• Any computer (preferably a server) that can run
• Linux-type Operating System
• RAM memory about 2GB
• Hard disk Size
(Repository size will decide the storage capacity)
Software Configuration
• Linux Operating System (Ubuntu, Fedora, Debian, Suse, Red Hat)
• Java Software
• Apache 2 or higher (web application service)
• Tomcat 5 or higher (web application service)
• PostgreSQL 8.3 (database software)
• DSpace 1.5
3
Chapter 1
VMware Player installation
What is the VMware Player?
•VMware Player is free software that enables users to easily run any
virtual machine on a Windows or Linux PC
•VMware Player enables you to run, evaluate and share software in a
virtual machine
•A virtual machine is a self-contained operating environment that
behaves as if it is a separate computer
•Essentially, you’ll use VMware Player to emulate a pre-installed
version of DSpace so that you don’t have to set up all the hardware
and software required to work with DSpace yourself
4
VMware Player installation
continues….
Why does this VM look so strange? It’s supposed to
be another PC, so where is Windows?
The operating system that is preloaded on this Virtual Machine is a
Linux distribution named Ubuntu and you will, at first, see the textbased console (shell) that is popular with Linux users.
For those of you with experience using MS-DOS, this text-based
environment shouldn’t be new.
Remember, though, that the only purpose of using VMware Player is
to have a version of DSpace pre-installed on your PC so that you can
work with DSpace.
It is expected that you may have trouble with a command-line
interface, so don’t worry if the shell CLI environment seems strange
and intimidating.
5
6
7
8
Copy and start the VMWare Image
Copy the contents of the DVDs to somewhere easy accessible
i.e:
C:\vmware_images\dspace
9
10
11
12
13
Watch you DSpace vmware image boot up
14
Note:
If you want to shut down your virtual
machine, type
sudo halt
and after a few moments vmware
player will close. If you simply close the
player, the virtual machine will
'hybernate' and not shut down properly.
It is strongly advisable to use the shut
down command instead.
15
Chapter 2
Configure your server setting to your
network requirements. Continue to edit
your DSpace settings to suit your setup.
16
Log on to your VMWare image with:
user = dspace ; password = dspace
17
Your vm machine has been set up to automatically
obtain an IP.
To find out your vm's IP, do the following:
$ sudo ifconfig
sudo means super user do and allows you to work as if you were an administrator
ifconfig means interface configurator and allows you to view or control a computer’s network
interfaces
[type dspace when prompted for a password]
18
If you don’t see an IP Address, follow
these steps:
$ cd /etc/network
$ sudo nano interfaces
19
Add the following lines
Reset network interface: $ sudo /etc/init.d/networking restart
$ sudo reboot
20
Check again whether you can see an IP
Address:
$ sudo ifconfig
[type dspace when prompted for a password]
21
Make a note of your IP address
In the example the IP address is 192.168.44.128
Open your web browser and point it to the IP above in the
following way:
http://192.168.44.128/jspui - replacing 192.168.44.128.
with the IP you noted previously
22
Now you should see your DSpace
opening up from your vmware image
23
Now we need to change the configuration
on DSpace to personalize it and get
working with your details
Edit the dspace.cfg file by typing the
following lines in the black console:
$ cd /dspace/config
$ sudo nano dspace.cfg
24
Continue…
•
Now look for the following lines and edit them:
dspace.url = http://dspace.local/jspui
#change if testing on network
•
dspace.hostname = dspace.local
#change if testing on network
•
dspace.name = dspace Collection
•
mail.server = localhost
#campus mail server here
•
mail.from.address = dspace-noreply@localhost
# change from localhost
•
feedback.recipient = [email protected]
•
mail.admin = [email protected]
•
To exit the editor, press CTRL + X, and Yes to save
25
Continue…
$ cd /dspace-source/dspace-1.5.0-release/dspace/target/dspace-1.5.0-build.dir
$ sudo ant update
$ sudo /etc/init.d/postgresql-8.3 restart
$ sudo /etc/init.d/tomcat5.5 restart
26
Continue…
Create an admin account to login to
DSpace with:
$ sudo /dspace/bin/create-administrator
The following admin user has already
been set up:
User:
dspace@local
Password: dspace
27
ANY QUESTIONS?
With Special Thanks to Laurence Munro(Stellenbosch University) for creating
the image and his assistance!!
28