Transcript Fundamentals of Audio Production - Info

Fundamentals of Audio
Production
Chapter Six:
Recording, Storing, and Playback
of Sound
Fundamentals of Audio
Production. Chapter 6.
1
Mechanical storage
• The phonograph – cylinder recorder/player
developed by Thomas Edison.
Fundamentals of Audio
Production. Chapter 6.
2
Mechanical storage
• Gramophone – Emil Berliner’s disk-based
mechanical recorder
Fundamentals of Audio
Production. Chapter 6.
3
Mechanical storage
• By “shouting into the funnel,” a diaphragm
at the small end would vibrate
• A stylus attached to the diaphragm would
vibrate and cut a groove into the cylinder
or disk
• On playback, the stylus would track
through the groove, causing vibrations in
the diaphragm, which echoed through the
funnel
Fundamentals of Audio
Production. Chapter 6.
4
Mechanical storage
• Modern record cutting lathes use
electromagnetic heads to convert audio
current into physical vibrations
• The electromagnets respond to audio
current by alternatively pushing/pulling the
stylus
• The vibrating stylus is heated to easily cut
a groove in the vinyl disk
Fundamentals of Audio
Production. Chapter 6.
5
Mechanical storage
Fundamentals of Audio
Production. Chapter 6.
6
Mechanical storage
Fundamentals of Audio
Production. Chapter 6.
7
Mechanical storage
• Modern phonographs use electromagnetic
transducers called cartridges
• Cartridges convert potential physical
energy, which is stored in the grooves of
the recording, into electrical energy
• The stylus follows the undulating groove
• Movements of the stylus, vibrate a small
magnet/coil mechanism
Fundamentals of Audio
Production. Chapter 6.
8
Mechanical storage
Fundamentals of Audio
Production. Chapter 6.
9
Magnetic tape recording
• Magnetic recording heads are transducers
that convert electrical energy into
magnetic energy
• Recording heads are electromagnets
• Audio current creates an alternating
magnetic field
• The magnetic field is focused at the “gap”
in the record head
Fundamentals of Audio
Production. Chapter 6.
10
Magnetic tape recording
Fundamentals of Audio
Production. Chapter 6.
11
Magnetic tape recording
• The fluctuations in the magnetic field are
stored on tape by re-arranging the
magnetic polarity of the “metal” surface of
the tape
• The tape surface is made from powdered
metals, like FeO2, or iron oxide (rust)
• The metals are attached to a plastic
backing with binder (glue)
Fundamentals of Audio
Production. Chapter 6.
12
Magnetic tape recording
• Playback heads are constructed in a
nearly identical manner
• During playback, a current is induced to
flow in the coil of the head by the magnetic
charges of the tape surface
Fundamentals of Audio
Production. Chapter 6.
13
Analog tape recording
• The paths on the tape where audio is
recorded are called “tracks”
• The inputs on the recorder are called
“channels”
• Stereo formats are two channel, but may
be two or four tracks
Fundamentals of Audio
Production. Chapter 6.
14
Analog tape recording
Fundamentals of Audio
Production. Chapter 6.
15
Analog tape recording
• Tape width and track spacing affect cross
talk between tracks
• Tape speed affects fidelity
– Higher tape speeds produce greater signal-tonoise ratios
– Higher tape speeds produce wider frequency
responses
Fundamentals of Audio
Production. Chapter 6.
16
Analog tape recording
The Philips compact cassette
and track configuration
Fundamentals of Audio
Production. Chapter 6.
17
Analog tape recording
Reel to reel
Fundamentals of Audio
Production. Chapter 6.
18
Analog tape recording
Reel to reel
Fundamentals of Audio
Production. Chapter 6.
19
Analog tape recording
Cartridges
Fundamentals of Audio
Production. Chapter 6.
20
Analog tape recording
• Commonalities across tape platforms
– Head arrangements
• First erase, second record, and last reproduce
– Capstan and pinch roller squeeze together
and pull the tape
Fundamentals of Audio
Production. Chapter 6.
21
Analog tape recording
Fundamentals of Audio
Production. Chapter 6.
22
Digital tape recording
• Digital audio tape stores binary data
(on/off) represented by short bursts of
electrical current
• Stationary head systems (DASH) use reelto-reel tape transports
• DAT systems use helical scanning rotating
head
Fundamentals of Audio
Production. Chapter 6.
23
Digital tape recording
Fundamentals of Audio
Production. Chapter 6.
24
Optical storage
• Electrical energy is converted into light
energy by a LASER
• The LASER burns microscopic pits into
the surface of a glass disk
• Binary data (on/off) triggers the LASER
Fundamentals of Audio
Production. Chapter 6.
25
Optical storage
Fundamentals of Audio
Production. Chapter 6.
26
Optical storage
• Compact disks are read by a LASER
• Light is refracted into a photoreceptor by
“bumps” on the surface of the disk
• Each pulse of light is equal to an “on” state
Fundamentals of Audio
Production. Chapter 6.
27
Optical storage
Fundamentals of Audio
Production. Chapter 6.
28
Optical storage
• The pits made by the LASER are .5
microns wide and up to 3.5 microns in
length
• How big is that?
• http://www.cellsalive.com/howbig.htm
• Data is stored redundantly on the disk to
avoid destruction or obliteration by dirt
Fundamentals of Audio
Production. Chapter 6.
29
Solid state storage
• “Flash” memory is constructed from layers
of layers of conductive and non-conductive
materials
• The layers function as transistors
• Current is passed through the device’s
thousands of transistors
• If it passes through, it represents an “on”
in binary code
Fundamentals of Audio
Production. Chapter 6.
30
Solid state storage
Fundamentals of Audio
Production. Chapter 6.
31
Solid state storage
Fundamentals of Audio
Production. Chapter 6.
32
Discussion
• What are the relative advantages and
disadvantages of
– Mechanical
– Magnetic
– Optical
– Solid state
Fundamentals of Audio
Production. Chapter 6.
33