Transcript SiO 2

ECE484: Digital VLSI Design
Fall 2010
Lecture: IC Manufacturing
Mary Jane Irwin ( www.cse.psu.edu/~mji )
www.cse.psu.edu/~cg477
Edited by Dr. George Engel
[Adapted from Rabaey’s Digital Integrated Circuits, ©2002, J. Rabaey et al.]
CSE477 L05 IC Manufacturing.1
Irwin&Vijay, PSU, 2002
Growing the Silicon Ingot
From Smithsonian, 2000
CSE477 L05 IC Manufacturing.2
Irwin&Vijay, PSU, 2002
CMOS Process at a Glance
Define active areas
Etch and fill trenches

One full photolithography
sequence per layer
(mask)

Built (roughly) from the
bottom up
Implant well regions
Deposit and pattern
polysilicon layer
Implant source and drain
regions and substrate contacts
5
4
2
3
1
metal 2
metal 1
polysilicon
exception!
source and drain diffusions
tubs (aka wells, active areas)
Create contact and via windows
Deposit and pattern metal layers
CSE477 L05 IC Manufacturing.3
Irwin&Vijay, PSU, 2002
Photolithographic Process
optical
mask
oxidation
stepper
exposure
photoresist
removal
(ashing)
photoresist coating
photoresist
development
process
step
spin, rinse,
dry
CSE477 L05 IC Manufacturing.4
acid etch
Irwin&Vijay, PSU, 2002
Patterning - Photolithography
1. Oxidation
UV light
mask
2. Photoresist (PR) coating
3. Stepper exposure
SiO2
PR
4. Photoresist development
and bake
5. Acid etching
Unexposed (negative PR)
Exposed (positive PR)
6. Spin, rinse, and dry
7. Processing step
Ion implantation
Plasma etching
Metal deposition
8. Photoresist removal (ashing)
CSE477 L05 IC Manufacturing.5
Irwin&Vijay, PSU, 2002
Example of Patterning of SiO2
Chemical or plasma
etch
Hardened resist
SiO
2
Si-substrate
Si-substrate
Silicon base material
Photoresist
SiO2
4. After development and
etching of resist, chemical or
plasma etch of SiO2
Si-substrate
1&2. After oxidation and
deposition of negative
photoresist
UV-light
Patterned
optical mask
Hardened resist
SiO2
Si-substrate
5. After etching
Exposed resist
Si-substrate
3. Stepper exposure
CSE477 L05 IC Manufacturing.6
SiO2
Si-substrate
8. Final result after
removal of resist
Irwin&Vijay, PSU, 2002
Diffusion and Ion Implantation
1. Area to be doped is
exposed
(photolithography)
2. Diffusion
or
Ion implantation
CSE477 L05 IC Manufacturing.7
Irwin&Vijay, PSU, 2002
Deposition and Etching
1. Pattern masking
(photolithography)
2. Deposit material over
entire wafer
CVD (Si3N4)
chemical deposition
(polysilicon)
sputtering (Al)
3. Etch away unwanted
material
wet etching
dry (plasma) etching
CSE477 L05 IC Manufacturing.8
Irwin&Vijay, PSU, 2002
Planarization: Polishing the Wafers
From Smithsonian, 2000
CSE477 L05 IC Manufacturing.9
Irwin&Vijay, PSU, 2002
Self-Aligned Gates
1. Create thin oxide in the
“active” regions, thick
elsewhere
2. Deposit polysilicon
3. Etch thin oxide from
active region (poly acts as
a mask for the diffusion)
4. Implant dopant
CSE477 L05 IC Manufacturing.10
Irwin&Vijay, PSU, 2002
A Modern CMOS Process
Dual-Well Trench-Isolated CMOS
gate oxide
field oxide
Al (Cu)
SiO2
TiSi2
tungsten
p well
SiO2
n well
p-epi
n+
p+
p-
CSE477 L05 IC Manufacturing.11
Irwin&Vijay, PSU, 2002
Modern CMOS Process Walk-Through
Base material: p+ substrate
with p-epi layer
p-epi
p+
SiN
34
p-epi
p+
p+
CSE477 L05 IC Manufacturing.12
SiO
2
After deposition of gate-oxide
and sacrifical nitride (acts as a
buffer layer)
After plasma etch of insulating
trenches using the inverse of
the active area mask
Irwin&Vijay, PSU, 2002
CMOS Process Walk-Through, con’t
SiO After trench filling, CMP
2
planarization, and
removal of sacrificial
nitride
n
p
CSE477 L05 IC Manufacturing.13
After n-well and VTp
adjust implants
After p-well and VTn adjust
implants
Irwin&Vijay, PSU, 2002
CMOS Process Walk-Through, con’t
poly(silicon)
After polysilicon deposition
and etch
n+
p+
After n+ source/dram and
p+ source/drain implants.
These steps also dope the
polysilicon.
SiO
2
After deposition of SiO2
insulator and contact
hole etch
CSE477 L05 IC Manufacturing.14
Irwin&Vijay, PSU, 2002
CMOS Process Walk-Through, con’t
Al
After deposition and
patterning of first Al
layer.
Al
SiO
2
After deposition of SiO2
insulator, etching of via’s,
deposition and patterning
of second layer of Al.
CSE477 L05 IC Manufacturing.15
Irwin&Vijay, PSU, 2002
Layout Editor: max Design Frame
CSE477 L05 IC Manufacturing.16
Irwin&Vijay, PSU, 2002
max Layer Representation

Metals (five) and vias/contacts
between the interconnect levels


CSE477 L05 IC Manufacturing.17
Note that m5 connects only to m4, m4
only to m3, etc., and m1 only to poly,
ndif, and pdif
Some technologies support “stacked
vias”

Active – active areas on/in
substrate (poly gates, transistor
channels (nfet, pfet), source and
drain diffusions (ndif, pdif), and well
contacts (nwc, pwc))

Wells (nw) and other select areas
(pplus, nplus, prb)
Irwin&Vijay, PSU, 2002
CMOS Inverter max Layout
Out
In
metal1-poly via
metal1
polysilicon
metal2
VDD
pfet
PMOS (4/.24 = 16/1)
pdif
NMOS (2/.24 = 8/1)
metal1-diff via
ndif
nfet
GND
metal2-metal1 via
CSE477 L05 IC Manufacturing.18
Irwin&Vijay, PSU, 2002
Simplified Layouts in max

Online design rule checking (DRC)

Automatic fet generation (just overlap poly and diffusion
and it creates a transistor)

Simplified via/contact generation


v12, v23, v34, v45
ct, nwc, pwc
0.44 x 0.44 m1
0.3 x 0.3 ct
0.44 x 0.44 poly
CSE477 L05 IC Manufacturing.19
Irwin&Vijay, PSU, 2002
Design Rule Checker
poly_not_fet to all_diff minimum spacing = 0.14 um
CSE477 L05 IC Manufacturing.20
Irwin&Vijay, PSU, 2002
Design Rules

Interface between the circuit designer and process
engineer

Guidelines for constructing process masks

Unit dimension: minimum line width


scalable design rules: lambda parameter
absolute dimensions: micron rules

Rules constructed to ensure that design works even
when small fab errors (within some tolerance) occur

A complete set includes



set of layers
intra-layer: relations between objects in the same layer
inter-layer: relations between objects on different layers
CSE477 L05 IC Manufacturing.21
Irwin&Vijay, PSU, 2002
Why Have Design Rules?

To be able to tolerate some level of fabrication errors
such as
1. Mask misalignment
2. Dust
3. Process parameters
(e.g., lateral diffusion)
4. Rough surfaces
CSE477 L05 IC Manufacturing.22
Irwin&Vijay, PSU, 2002
Intra-Layer Design Rule Origins

Minimum dimensions (e.g., widths) of objects on each
layer to maintain that object after fab


minimum line width is set by the resolution of the patterning
process (photolithography)
Minimum spaces between objects (that are not related)
on the same layer to ensure they will not short after fab
0.3 micron
0.15
0.15
CSE477 L05 IC Manufacturing.23
0.3 micron
Irwin&Vijay, PSU, 2002
Intra-Layer Design Rules
Same Potential
0
or
6
Well
Different Potential
2
9
Polysilicon
2
10
3
Active
Contact
or Via
Hole
3
2
Select
3
Metal1
2
2
3
4
Metal2
3
CSE477 L05 IC Manufacturing.24
Irwin&Vijay, PSU, 2002
Inter-Layer Design Rule Origins
1.
Transistor rules – transistor formed by overlap of active
and poly layers
Transistors
Catastrophic
error
Unrelated Poly & Diffusion
Thinner diffusion,
but still working
CSE477 L05 IC Manufacturing.25
Irwin&Vijay, PSU, 2002
Transistor
Transistor Layout
1
3
2
5
CSE477 L05 IC Manufacturing.26
Irwin&Vijay, PSU, 2002
Select Layer
2
3
Select
2
1
3
3
2
Substrate
CSE477 L05 IC Manufacturing.27
5
Well
Irwin&Vijay, PSU, 2002
Inter-Layer Design Rule Origins, Con’t
2.
Contact and via rules
M1 contact to p-diffusion
M1 contact to n-diffusion
Contact Mask
M1 contact to poly
Mx contact to My
both materials
0.3
Via Masks
mask misaligned
Contact: 0.44 x 0.44
0.14
CSE477 L05 IC Manufacturing.28
Irwin&Vijay, PSU, 2002
Vias and Contacts
2
4
Via
1
1
5
Metal to
1
Active Contact
Metal to
Poly Contact
3
2
2
2
CSE477 L05 IC Manufacturing.29
Irwin&Vijay, PSU, 2002