Transcript Lecture 1 - Auburn University

VLSI Testing
Dr. Vishwani D. Agrawal
James J. Danaher Professor of Electrical and
Computer Engineering
Auburn University, Alabama 36849, USA
[email protected]
http://www.eng.auburn.edu/~vagrawal
July 30 – August 13, 2009
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
1
Course Description
This course is designed for the MTech program
in VLSI at IIT, Delhi. It is patterned after a onesemester graduate-level course offered at
Auburn University. A set of 14 lectures that
include classroom exercises provide
understanding of theoretical and practical
aspects of VLSI testing. The course fulfills the
needs of today’s industrial design
environment, which demands knowledge of
testing concepts of digital, memory, analog
and radio frequency (RF) subsystems often
implemented on a system-on-chip (SoC).
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
2
Outline


















Lecture
Lecture
Lecture
Lecture
Lecture
Lecture
Lecture
Lecture
Test 1
Lecture
Lecture
Lecture
Lecture
Lecture
Lecture
Test 2
Lecture
Lecture
1:
2:
3a:
3b:
4a:
4b:
5:
6:
Introduction (19*+1)
* Number of slides
Yield and quality (16+2)
Fault modeling (19+2)
Testability analysis (26)
Logic simulation (14)
Fault simulation (18)
Combinational ATPG (24+2)
Sequential ATPG (19+1)
7:
8:
9:
10:
11:
12:
Delay test (25)
Memory test (25)
Analog test (24)
DFT and Scan (24+2)
BIST (28)
System diagnosis (20)
13:
14:
RF Testing: Introduction, gain measurement (39)
RF Testing: Intermodulation and noise measurements (33)
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
3
Schedule







July 30, 2009 – 3-5PM Lectures 1 and 2
July 31, 2009 – 3-5PM Lectures 3 and 4
Aug 1, 2009 – 9AM-1PM Lectures 5, 6, 7 and 8
Aug 3, 2009 – 3-5PM Lectures 9 and 10
Aug 11, 2009 – 3-5PM Lectures 11 and 12
Aug 12, 2009 – 3-5PM Lectures 13 and 14
Aug 13, 2009 – 3-5PM Lectures 15 and 16
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
4
Lecture 1: Introduction









VLSI realization process
Verification and test
Ideal and real tests
Costs of testing
Roles of testing
A modern VLSI device - system-on-a-chip
Testing
Digital
Memory
Analog
RF
Textbook
Problem to solve
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
5
VLSI Realization Process
Customer’s need
Determine requirements
Write specifications
Design synthesis and Verification
Test development
Fabrication
Manufacturing test
Chips to customer
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
6
Definitions



Design synthesis: Given an I/O function, develop a
procedure to manufacture a device using known
materials and processes.
Verification: Predictive analysis to ensure that the
synthesized design, when manufactured, will perform
the given I/O function.
Test: A manufacturing step that ensures that the
physical device, manufactured from the synthesized
design, has no manufacturing defect.
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
7
Verification vs. Test




Verification
Verifies correctness of
design.
Performed by simulation,
hardware emulation, or
formal methods.
Performed once prior to
manufacturing.
Responsible for quality of
design.
Copyright 2001, Agrawal & Bushnell




Test
Verifies correctness of
manufactured hardware.
Two-part process:
1. Test generation: software
process executed once
during design
2. Test application: electrical
tests applied to hardware
Test application performed on
every manufactured device.
Responsible for quality of
devices.
Lecture 1 Introduction
8
Problems of Ideal Tests




Ideal tests detect all defects produced in the
manufacturing process.
Ideal tests pass all functionally good devices.
Very large numbers and varieties of possible
defects need to be tested.
Difficult to generate tests for some real defects.
Defect-oriented testing is an open problem.
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
9
Real Tests




Based on analyzable fault models, which may not
map on real defects.
Incomplete coverage of modeled faults due to
high complexity.
Some good chips are rejected. The fraction (or
percentage) of such chips is called the yield loss.
Some bad chips pass tests. The fraction (or
percentage) of bad chips among all passing chips
is called the defect level.
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
10
Testing as Filter Process
Good chips
Prob(good) = y
Prob(pass test) = high
Tested
chips
Fabricated
chips
Defective chips
Prob(bad) = 1- y
Copyright 2001, Agrawal & Bushnell
Mostly
good
chips
Prob(fail test) = high
Lecture 1 Introduction
Mostly
bad
chips
11
Costs of Testing



Design for testability (DFT)
Chip area overhead and yield reduction
Performance overhead
Software processes of test
Test generation and fault simulation
Test programming and debugging
Manufacturing test
Automatic test equipment (ATE) capital cost
Test center operational cost
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
12
Present and Future*
1997 -2001
2003 - 2006
Feature size (micron)
Transistors/sq. cm
0.25 - 0.15
4 - 10M
0.13 - 0.10
18 - 39M
Pin count
Clock rate (MHz)
Power (Watts)
100 – 900
200 – 730
1.2 – 61
160 - 1475
530 - 1100
2 - 96
* SIA Roadmap, IEEE Spectrum, July 1999
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
13
Design for Testability (DFT)
DFT refers to hardware design styles or added hardware
that reduces test generation complexity.
Motivation: Test generation complexity increases
exponentially with the size of the circuit.
Example: Test hardware applies tests to blocks A
and B and to internal bus; avoids test generation
for combined A and B blocks.
Int.
Primary
Primary
Logic
bus
Logic
outputs
inputs
block A
block B
(PO)
(PI)
Test
input
Copyright 2001, Agrawal & Bushnell
Test
output
Lecture 1 Introduction
14
Cost of Manufacturing
Testing in 2000AD



0.5-1.0GHz; analog instruments; 1,024 digital pins: ATE
purchase price
= $1.2M + 1,024 x $3,000 = $4.272M
Annual running cost (five-year linear depreciation)
= Depreciation (1/5) + Maintenance (2%) + Operation ($0.5M)
= $0.854M + $0.085M + $0.5M
= $1.439M/year
Test cost (24 hour ATE operation)
= $1.439M/(365 x 24 x 3,600)
= 4.5 cents/second
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
15
Roles of Testing




Detection: Determination whether or not the device
under test (DUT) has some fault.
Diagnosis: Identification of a specific fault that is
present on DUT.
Device characterization: Determination and
correction of errors in design and/or test
procedure.
Failure mode analysis (FMA): Determination of
manufacturing process errors that may have
caused defects on the DUT.
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
16
A Modern VLSI Device
System-on-a-chip (SOC)
Data
terminal
Copyright 2001, Agrawal & Bushnell
DSP
core
RAM
ROM
Interface
logic
Mixedsignal
Codec
Lecture 1 Introduction
Transmission
medium
17
Textbooks


Digital, memory and mixed-signal:
M. L. Bushnell and V. D. Agrawal, Essentials of Electronic
Testing for Digital, Memory and Mixed-Signal VLSI
Circuits, Springer, 2000.
http://www.eng.auburn.edu/~vagrawal/BOOK/books.html
RF
To be supplied in Lectures 13 and 14.
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
18
Problem to Solve

Using the testing cost obtained in Slide 15,
determine what is the component of test in the
cost of a mixed-signal VLSI chip for the
following data:
Analog test time = 1.5 s
Digital test clock = 200MHz
Number of digital test vectors = 109
Chip yield = 70%
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
19
Solution
Assuming that one vector is applied per clock cycle during the digital test, the
rate of test application is 200 million vectors per second. Therefore,
Digital test time = (1000 × 106)/(200× 106) = 5 seconds
Adding the analog test time, we get,
Total test time = 1.5 + 5.0 = 6.5 seconds
The testing cost for a 500 MHz, 1,024 pin tester was obtained as 4.56 cents in
Slide 15. Thus,
Cost of testing a chip = 6.5 × 4.56 = 29.64 cents
The cost of testing bad chips should also be recovered from the price of good
chips. Since the yield of good chips is 70%, we obtain
Test cost in the price of a chip = 29.64/0.7 ≈ 42 cents
42 cents should be included as the cost of testing while figuring out the
price of chips.
Copyright 2001, Agrawal & Bushnell
Lecture 1 Introduction
20