Transcript Read Only Memory (ROM) - ncdigitalmedia-computer

Russell Taylor
RAM Quiz
 http://computer.howstuffworks.com/ram-quiz.htm
ROM Types
 Read-only memory (ROM), also known as firmware, is an
integrated circuit programmed with specific data when it
is manufactured.
 ROM chips are used not only in computers, but in most
other electronic items as well. There are five basic ROM
types:
 ROM
 PROM
 EPROM
 EEPROM
 Flash memory
Volatility
 Each type has unique characteristics, but they are all
types of memory with two things in common: Data stored
in these chips is nonvolatile -- it is not lost when power is
removed.
 Data stored in these chips is either unchangeable or
requires a special operation to change (unlike RAM, which
can be changed as easily as it is read).
 This means that removing the power source from the chip
will not cause it to lose any data.
ROM at work
 Similar to RAM, ROM chips (Figure 1) contain a grid of
columns and rows. But where the columns and rows
intersect, ROM chips are fundamentally different from
RAM chips.
 While RAM uses transistors to turn on or off access to a
capacitor at each intersection, ROM uses a diode to
connect the lines if the value is 1.
 If the value is 0, then
the lines are not connected at all.
How Diodes Work
 A diode normally allows current to flow in only one direction and




has a certain threshold, known as the forward breakover, that
determines how much current is required before the diode will pass
it on.
In silicon-based items such as processors and memory chips, the
forward breakover voltage is approximately 0.6 volts.
By taking advantage of the unique properties of a diode, a ROM chip
can send a charge that is above the forward breakover down the
appropriate pathway connected to a specific cell.
If a diode is present at that cell, the charge will be conducted
through to the ground, and, under the binary system, the cell will be
read as being "on" (a value of 1).
If the cell's value is 0, there is no diode at that intersection to
connect the column and row. So the charge on the pathway does
not get transferred to the row.
ROMs need to be perfect!
 The way a ROM chip works necessitates the programming of perfect and




complete data when the chip is created.
You cannot reprogram or rewrite a standard ROM chip. If it is incorrect, or
the data needs to be updated, you have to throw it away and start over.
Creating the original template for a ROM chip is often a laborious process
full of trial and error. But the benefits of ROM chips outweigh the
drawbacks.
Once the template is completed, the actual chips can cost as little as a few
pence each. They use very little power, are extremely reliable and, in the
case of most small electronic devices, contain all the necessary
programming to control the device.
A great example is the small chip in the singing fish toy. This chip, about the
size of your fingernail, contains the 30-second song clips in ROM and the
control codes to synchronize the motors to the music.
PROM(programmable read-only memory)
 Creating ROM chips totally from scratch is time-consuming and very




expensive in small quantities.
For this reason, mainly, developers created a type of ROM known as
programmable read-only memory (PROM).
Blank PROM chips can be bought inexpensively and coded by
anyone with a special tool called a programmer. PROM chips have a
grid of columns and rows just as ordinary ROMs do. The difference is
that every intersection of a column and row in a PROM chip has a
fuse connecting them.
PROMs can only be programmed once. They are more fragile than
ROMs.
A jolt of static electricity can easily cause fuses in the PROM to burn
out, changing essential bits from 1 to 0. But blank PROMs are
inexpensive and are great for prototyping the data for a ROM before
committing to the costly ROM fabrication process.
EPROM(Erasable programmable read-only memory )
 Working with ROMs and PROMs can be a wasteful business. Even though they are inexpensive
per chip, the cost can add up over time. Erasable programmable read-only memory (EPROM)
addresses this issue.
 EPROM chips can be rewritten many times. Erasing an EPROM requires a special tool that
emits a certain frequency of ultraviolet (UV) light.
 EPROMs are configured using an EPROM programmer that provides voltage at specified levels
depending on the type of EPROM used.
 To rewrite an EPROM, you must erase it first. To erase it, you must supply a level of energy
strong enough to break through the negative electrons blocking the floating gate.
 In a standard EPROM, this is best accomplished with UV light at a frequency of 253.7. Because
this particular frequency will not penetrate most plastics or glasses, each EPROM chip has a
quartz window on top of it. The EPROM must be very close to the eraser's light source, within
an inch or two, to work properly.
 An EPROM eraser is not selective, it will erase the entire EPROM. The EPROM must be
removed from the device it is in and placed under the UV light of the EPROM eraser for
several minutes. An EPROM that is left under too long can become over-erased.
EEPROMs and Flash Memory
 Though EPROMs are a big step up from PROMs in terms
of reusability, they still require dedicated equipment and
a labour-intensive process to remove and reinstall them
each time a change is necessary. Also, changes cannot be
made incrementally to an EPROM; the whole chip must
be erased. Electrically erasable programmable read-only
memory (EEPROM) chips remove the biggest drawbacks
of EPROMs.
Advantages of EEPROMs
 In EEPROMs:
 The chip does not have to removed to be rewritten.
 The entire chip does not have to be completely erased to change a specific





portion of it.
Changing the contents does not require additional dedicated equipment.
Instead of using UV light, you can return the electrons in the cells of an
EEPROM to normal with the localized application of an electric field to each
cell. This erases the targeted cells of the EEPROM, which can then be rewritten.
EEPROMs are changed 1 byte at a time, which makes them versatile but slow.
Manufacturers responded to this limitation with Flash memory, a type of
EEPROM that uses in-circuit wiring to erase by applying an electrical field to the
entire chip or to predetermined sections of the chip called blocks.
Flash memory works much faster than traditional EEPROMs because it writes
data in chunks, usually 512 bytes in size, instead of 1 byte at a time.
How Flash Memory Works
 http://www.howstuffworks.com/flash-memory.htm