Transcript Mains Electricity

Contents
Mains Electricity
Alternating current and direct current
Electricity in the home
Fuses and circuit breakers
Buying electricity
Summary activities
1 of 40
© Boardworks Ltd 2005
What is direct current (d.c.)?
Direct current (d.c.) is an
electric current that always
flows in one direction.
Direct current is produced by
cells and batteries.
Electronic circuits such as
those in computers and
stereos need direct current
electricity in order to work.
Direct current cannot be
transferred efficiently over
large distances.
2 of 40
© Boardworks Ltd 2005
What is alternating current (a.c.)?
Alternating current (a.c.) is
an electric current that is
constantly changing direction.
Alternating current is produced
by most generators and is
used in mains electricity.
Motors often work using
alternating current. The
voltage of alternating
current is easily changed
with a transformer.
Alternating current can be
transferred efficiently over
large distances.
3 of 40
© Boardworks Ltd 2005
Comparing a.c. and d.c.
d.c.
time
voltage
voltage
The difference between alternating current (a.c.) and
direct current (d.c.) can be seen using an oscilloscope.
For each current, the oscilloscope trace is a graph showing
how the voltage of an electricity supply varies with time.
peak forward
voltage
a.c.
time
peak reverse
voltage
The voltage of a d.c. supply
is steady and always in the
same direction.
4 of 40
The voltage of an a.c. supply
follows a repeated pattern: it
rises to a peak, returns to zero
changes direction and so on.
© Boardworks Ltd 2005
Frequency of alternating current
voltage
The frequency of a.c. electricity is the number of complete
cycles per second, which is measured in hertz (Hz).
1 complete cycle
peak forward
voltage
a.c.
time
peak reverse
voltage
The a.c. frequency can be determined from an oscilloscope
by counting the number of complete waves per unit time.
If the frequency is increased the number of complete waves
shown on the screen increases. For example, if the
frequency is doubled the number of waves doubles.
5 of 40
© Boardworks Ltd 2005
Mains electricity in the UK
In the UK, the frequency of
mains electricity is 50 hertz:
this alternating current flows
backwards and forwards
50 times per second.
This frequency is the same
at any point in the electricity
supply system but the
voltage varies in different
parts of the national grid.
The voltage of mains electricity supplied to UK homes is 230 V.
This is an effective voltage which is equal to the voltage of
a d.c. supply that would produce the same heating effect.
The peak (maximum) voltage is higher than this.
6 of 40
© Boardworks Ltd 2005
Alternating current simulation
7 of 40
© Boardworks Ltd 2005
Which type of current – a.c. or d.c.?
8 of 40
© Boardworks Ltd 2005
Contents
Electricity: Mains electricity
Alternating current and direct current
Electricity in the home
Fuses and circuit breakers
Buying electricity
Summary activities
9 of 40
© Boardworks Ltd 2005
Electrical sockets
The mains electricity system
in your house is made up of
three types of wires: live,
neutral and earth.
Electrical sockets are a
convenient and safe way
of making the electricity
available for use.
Remember the electricity in a plug socket is at 230 V and
can easily kill you if you get a shock.
NEVER PUT ANYTHING OTHER THAN A PLUG
IN AN ELECTRICAL SOCKET!
10 of 40
© Boardworks Ltd 2005
Plugs and electrical cable
An electrical plug is inserted into
a socket and the cable which is
attached to the plug carries
electricity to the appliance.
The plug has three pins which
fit the three holes on the socket
in one way only, so the plug
cannot be connected wrongly.
The pins are made of brass,
which is a good conductor but
is hard and will not bend.
11 of 40
© Boardworks Ltd 2005
Inside an electrical cable
An electrical cable contains
three wires.
copper
These wires are made of copper
because it is a good conductor of
electricity. Each wire is made of
thin strands of copper to keep
the cable flexible.
Each wire is encased in plastic
to stop the wires touching and
causing a short circuit. Plastic is
used as it is a good insulator as
well as being tough and flexible.
The whole cable is encased in
another layer of plastic.
12 of 40
insulating plastic
© Boardworks Ltd 2005
Materials in a plug
13 of 40
© Boardworks Ltd 2005
Live, neutral and earth
The three wires in electrical cables have different functions.
The colour of the plastic casing tells you what the wire does.
live
earth
neutral
This colour-coding is a safety feature that makes the
wires easy to identify in poor lighting conditions.
14 of 40
© Boardworks Ltd 2005
What does each wire do?
The live wire carries a current
that alternates between a
negative and positive voltage.
The neutral wire completes the
circuit. It is kept at a zero voltage
by the electricity company.
15 of 40
The earth wire is a
safety wire that is needed
to earth appliances with
a metal case.
For example, if the live
wire becomes loose and
touches the metal case,
a very large current flows
to earth and blows the
fuse. This makes it safe
to touch the appliance.
© Boardworks Ltd 2005
Parts of a plug
earth
terminal
live
terminal
fuse
neutral
terminal
cable
grip
cable
16 of 40
© Boardworks Ltd 2005
Wiring a plug
When wiring a plug, always check the following:
 Make sure that the wires
are connected to the
correct terminals:
blue to neutral
yellow/green to earth
brown to live
 There are no loose or
bare wires.
 The grip should firmly
hold the cable in place.
 A fuse of the correct
value is fitted.
17 of 40
© Boardworks Ltd 2005
Plugs – true or false?
18 of 40
© Boardworks Ltd 2005
Contents
Electricity: Mains electricity
Alternating current and direct current
Electricity in the home
Fuses and circuit breakers
Buying electricity
Summary activities
19 of 40
© Boardworks Ltd 2005
What is a fuse?
A fuse is a safety device
that protects an electric
cable from overheating so
that the insulation does not
catch fire.
A plug contains a fuse to
prevent the case of a metal
appliance from becoming
live if a fault develops.
All plugs contain a fuse like
the one shown and are
simple to change if they
‘blow’ and break the
circuit.
20 of 40
© Boardworks Ltd 2005
How does a fuse work?
A fuse is a built-in weak point in a circuit. It contains a thin
wire with a higher resistance than normal wire.
terminals
thin wire with
high resistance
case made of
insulating material
When a large current flows the wire becomes hot. If too
much current flows, the wire overheats and melts, which
breaks the circuit.
21 of 40
© Boardworks Ltd 2005
Choosing the right fuse
The circuit symbol for a fuse is:
Fuses are labelled with the maximum
current that they are designed to allow.
To choose the correct fuse for a
device, always choose the nearest
one rated above the operating
current of the device.
Example:
If a kettle operates with an electrical current of 4.3 A,
what fuse should it be fitted with? 5 A fuse
You can choose from fuses of 3 A, 5A and 13A.
22 of 40
© Boardworks Ltd 2005
Choose which fuse to use
23 of 40
© Boardworks Ltd 2005
Circuit breakers
The electrical wiring in a building must be protected from
being overloaded so that it does not overheat.
This is the job of a ‘fuse box’, which used to contain fuse
wire but now contains circuit breakers to protect the wiring.
Circuit breakers do the same job as fuses but they are
electromagnetic switches which are easy to reset.
A house has several
circuits and each one is
protected by a separate
circuit breaker.
Circuit breakers have
different ratings as shown
by the coloured dots.
24 of 40
© Boardworks Ltd 2005
How does a circuit breaker work?
The circuit breakers in a ‘fuse
box’ are some of the most
important safety mechanisms in
your home.
Each circuit breaker is an
electromagnetic switch which is
designed to break the circuit
when the current gets too high.
switch
Too much current makes the
magnetic field produced by the
electromagnet strong enough to
open the switch.
The circuit breaker is said to ‘trip’
and switches off the current.
25 of 40
electromagnet
© Boardworks Ltd 2005
Domestic wiring system
lights
5A
30A
ring main
power points
kWh
meter
live neutral
26 of 40
earth
© Boardworks Ltd 2005
Contents
Electricity: Mains electricity
Alternating current and direct current
Electricity in the home
Fuses and circuit breakers
Buying electricity
Summary activities
27 of 40
© Boardworks Ltd 2005
Buying electricity
Electricity costs money,
which is why every home
has an electricity meter.
The meter records how much
electricity is used in a house
in units of electrical energy.
The units of electrical
energy are called kilowatt
hours (kWh).
The cost of an electricity bill
is calculated from the
number of units used.
28 of 40
© Boardworks Ltd 2005
Cost of electricity
The cost of electricity is the number of units of electrical
energy multiplied by the cost per unit:
cost = number of units x cost per unit
Example:
How much would 10 units of electricity cost at a price of
9p per unit?
cost = 10 units x 9 p/unit
= 90 p
29 of 40
© Boardworks Ltd 2005
Calculating the units of electricity
The amount of electrical energy (i.e. the amount of electricity)
used by an appliance depends on its power and how long
the electricity is used for:
electrical energy = power x time
Power is measured in kilowatts (kW) and the time is
measured in hours (h), so what are the units of electricity
measured in?
1 unit of electricity = 1 unit of electrical energy
= 1 kilowatt hour (kWh)
Example:
How many units of electricity is 17.6 kWh? 17.6 units
30 of 40
© Boardworks Ltd 2005
Buying electricity problem
A kettle uses 45.2 kWh of energy.
If electricity costs 10 p per unit, how
much does it cost to use the kettle?
Number of units:
number of units of electricity = number of kilowatt hours
= 45.2 units
Cost of electricity:
cost = number of units x cost per unit
= 45.2 units x 10 p / unit
= 452 p or £4.52
31 of 40
© Boardworks Ltd 2005
Buying electricity problem
An iron that operates at a power of 3 kW
for 4 hours uses electricity that costs 8p
per unit.
How much does it cost for the electricity
used by the iron in that time?
Number of units:
number of units of electricity = number of kilowatt hours
= 3 kW x 4 h
= 12 kWh
= 12 units
Cost of electricity:
cost = number of units x cost per unit
= 12 units x 8 p / unit
= 96p
32 of 40
© Boardworks Ltd 2005
Buying electricity calculations
33 of 40
© Boardworks Ltd 2005
Contents
Electricity: Mains electricity
Alternating current and direct current
Electricity in the home
Fuses and circuit breakers
Buying electricity
Summary activities
34 of 40
© Boardworks Ltd 2005
Glossary
 alternating current – A current that is constantly
changing direction.
 circuit breaker – An electromagnetic device that cuts off
the electrical supply if the current is too large.
 direct current – A current that is always flowing in one
direction.
 earth wire – This safety wire connects the metal case of
an appliance to earth.
 fuse – A length of wire that heats up and ‘blows’ (melts)
if the current is too large and so cuts off the electrical supply.
 live wire – This wire carries a current that alternates
between negative and positive values.
 neutral wire – This wire is kept at zero voltage by the
electricity company.
35 of 40
© Boardworks Ltd 2005
Anagrams
36 of 40
© Boardworks Ltd 2005
Multiple-choice quiz
37 of 40
© Boardworks Ltd 2005