Transcript 1.1 An introductory overview of power electronic

Chapter 1 Power Electronic Devices
Outline
1.1 An introductory overview of power electronic devices
1.2 Uncontrolled device—power diode
1.3 Half- controlled device—thyristor
1.4 Typical fully- controlled devices
1.5 Other new power electronic devices
1.1 An introductory overview of power electronic devices
1)
The concept and features
Power electronic devices: are the electronic devices that can be directly
used in the power processing circuits to convert or control electric
power.
Vacuum devices: Mercury arc
rectifier
In broad sense
Power electronic devices
thyratron, etc. . seldom
in use today
Semiconductor devices:
major power electronic devices
Very often: Power electronic devices= Power semiconductor devices
Major material used in power semiconductor devices——Silicon
Features of power electronic devices
a) The electric power that power electronic device deals with is usually
much larger than that the information electronic device does.
b) Usually working in switching states to reduce power losses
On-state
Voltage across the device is 0
p=vi=0
V=0
Off-state
Current through the device is 0
p=vi=0
i=0
c)Need to be controlled by information electronic circuits.
d)Very often, drive circuits are necessary to interface between
information circuits and power circuits.
e)Dissipated power loss usually larger than information electronic
devices —special packaging and heat sink are necessary.
2) Configuration of systems using power electronic devices
Power electronic system:
Electric isolation:
optical, magnetic
Control circuit (in a broad sense)
Control
circuit
detection circuit
drive circuit
Power circuit (power
stage, main circuit)
circuit
Protection circuit is also very often used in power electronic system
especially for the expensive power semiconductors.
Terminals of a power electronic device
A power electronic
device usually has
a third terminal —
—control terminal
to control the
states of the device
C
A power electronic device
must have at least two
terminals to allow power
circuit current flow through.
G
Drive
Circuit
E
Control signal from drive circuit must be connected between the control
terminal and a fixed power circuit terminal (therefore called common
terminal
Major topics for each device
Appearance, structure, and symbol
Physics of operation
Specification
Special issues
Devices of the same family
Passive components in power electronic circuit
Transformer, inductor, capacitor and resistor: these are passive
components in a power electron
ic circuit since they can not be controlled by control signal and their
characteristics are usually constant and linear.
The requirements for these passive components by power electronic
circuits could be very different from those by ordinary circuits.
1.2 Uncontrolled device Power diode

Appearance

PN junction
Direction of
inner electric field
-
-
-
-
+
+
+
+
-
-
-
-
+
+
+
+
-
-
-
-
+
+
+
+
-
-
-
-
+
+
+
+
-
-
-
-
+
+
+
+
p region
Space charge
Region
(depletion region,
potential
barrier region)
n region
PN junction with voltage applied in the forward direction
V
-
+
-
+
+
-
p
-
+
n
+
W
WO
+
PN junction with voltage applied in the reverse direction
Effective direction
of electronic field
-
+
V
-
+
+
-
p
-
+
n
+
-
WO
W
+

Construction of a practical power diode
Anode
+
+
P
V
-
19
-3
Na =10 cm
10μm
14
-3
Breakdown
Voltage dependent
19
-3
250μm
n + epi
Nd =10 cm
n- substrate
-3
Cathode
Nd =10 cm


Features different from low-power (information electronic) diodes
–Larger size
–Vertically oriented structure
–n drift region (p-i-n diode)
–Conductivity modulation
Junction capacitor
The positive and negative charge in the depletion region is variable with the
changing of external voltage. variable with the changing of external
voltage.
—–Junction capacitor C Junction capacitor CJ .
Potential barrier capacitor CB
Junction capacitor CJ
Diffusion capacitor CD
Junction capacitor influences the switching characteristics of
power diode.

Static characteristics of power diode
I
IF
UTO UF
O

Turn-off transient
IF
diF
dt
tF t 0
Turn- on transient
u
iF
i
UFP
trr
td
UF
U
tf
t1 t 2
diR
dt
IR
P
UR
t
uF
2V
0
UR
P
t fr
t

Examples of commercial power diodes
part number Rated max voltage
Fast recovery rectifiers
400V
1N3913
2500V
SD453N25S20PC
Ultra-fast recovery rectifiers
150V
MUR815
600V
MUR1560
1200V
RHRU100120
Schottky rectifiers
30V
MBR6030L
45V
444CNQ045
150V
30CPQ150
Rated vag current
VF(typical)
tr(max)
30A
400A
1.1V
2.2V
400ns
20μs
8A
15A
100A
0.975V
1.2V
2.6V
35ns
6ns
60ns
60A
440A
30A
0.48V
0.69V
1.19V
1.3 Half- controlled device—Thyristor
Another name: SCR—silicon controlled rectifier
Thyristor Opened the power electronics era
–1956, invention, Bell Laboratories
–1957, development of the 1st product, GE
–1958, 1st commercialized product, GE
–Thyristor replaced vacuum devices in almost every power processing
area.
Still in use in high power situation. Thyristor till has the
highest power-handling capability.

Appearance and symbol of thyristor
Structure and equivalent circuit of thyristor
Structure
A
Equivalent circuit
A
Equivalent
PNP
circuit
V
IA
P1
N1
N1
G
1
P2
P2
G
IG
Ic2
Ic1
NPN
V2
IK
N2
K
K
a)
b)
Physics of thyristor operation
Equivalent circuit: A pnp transistor and an npn
A
IA
transistor interconnected together
PNP
Positive feedback
V1
G
IG
S
Ic2
R
Trigger
Ic1
NPN
V2
Can not be turned off by control
EA
IK
EG
K
signal
Half-controllable
Quantitative description of thyristor operation
I c1=α1 IA + I CBO1
I c2= α2 IK + I CBO2
IK=IA+I
IA=Ic1+Ic2
G
IA
 2
IG  ICBO1 ICBO2
1  (1   2 )
（1-1）
（1-2）
（1-3）
（1-4）
( 1-5 )
When IG =0, α1+α2 is small.
When IG >0, α1 +α2 will approach 1, IA will be very large.


Other methods to trigger thyristor on
High voltage across anode and cathode—avalanche breakdown
High rising rate of anode voltagte —du/dt too high
High junction temperature
Light activation
Static characteristics of thyristor
Blocking when reverse biased, no matter if there is gate current applied.
Conducting only when forward biased and there is triggering current
applied to the gate.
Once triggered on, will be latched on conducting even when the gate
current is no longer applied.

Switching characteristics of thyristor
i
A
100%
90%
10%
0
u
td
t
tr
AK
I RM
t
O
t rr
URRM
tgr
1.4 Typical fully- controlled devices

Features
–IC fabrication technology, fully- controllable, high frequency
Applications
–Begin to be used in large amount in 1980s
–GTR is obsolete and GTO is also seldom used today.
–IGBT and power MOSFET are the two major power
semiconductor devices nowadays.

1.4.1 Gate- turn- off thyristor—GTO
Major difference from conventional thyristor:
The gate and cathode structures are highly interdigitated , with various types
of geometric forms being used to layout the gates and cathodes.

Physics of GTO operation
The basic operation of GTO is the
same as that of the conventional
thyristor. The principal
differences lie in the
modifications in the
structure to achieve gate turnoff capability.
–Large α2
–α1+α2 is just a little larger than
the critical value 1.
–Short distance from gate to
cathode makes it possible to
drive current out of gate.
A
IA
PNP
V1
G
IG
S
Ic2
R
Ic1
NPN
V2
EA
IK
EG
K
1.4.2 Giant Transistor—GTR
GTR is actually the bipolar junction transistor that can handle
high voltage and large current.
So GTR is also called power BJT, or just BJT.
Structures of GTR different from its information-processing
counterpart
Static characteristics of GTR
Ic
Saturation region
Amplifying (active) region
i b3
i b2
i b1
i b1<i b2<i b3
cut-off region
O
Uce
Second breakdown of GTR
Hard
Quasi-saturation
saturation
1
Rd
c
i
Second breakdown
IB5 >IB4. etc.
IB5
IB4
IB3
Active region
Primary
breakdown
IB2
IB<0
IB1
O
IB=0
IB=0
BVCEO
BVSUS
BVCBO UCE
1.4.3 Power metal- oxide- semiconductor field effect transistor—
Power MOSFET
A classification
Field Effect
Transistor
(FET)
Metal- onside-semiconductor FET (MOSFET)
n channel
Power MOSFET
p channel
Junction FET (JFET)
Static induction transistor (SIT)
Basic structure
Symbol
D
G
D
G
S
N channel
S
P channel
Physics of MOSFET operation (Off- state)
p-n- junction is
reverse-biased
off-state voltage
appears across
n- region


Physics of MOSFET operation (On-state)
p-n- junction is slightly reverse biased positive gate voltage induces
conducting channel drain current flows through n- region an
conducting channel on resistance = total resistances of nregion,conducting channel,source and drain contacts, etc.

Static characteristics of power
iD
[UGS-VGS(th)=UDS]
Ohmic
VGS5
Active
VGS5> VGS4 etc.
VGS4
VGS3
VGS2
VGS1
O
Cut off
BVDSS
VGS< VGS(th)
UDS

Switching characteristics of power MOSFET
+U E
RL
iD
Rs
up
RG uGS R D
F i
up
O
t
uGS
uGSP
uT
O
iD
t
O td(on)
Turn- on transient
–Turn- on delay time td(on)
–Rise time tr
tr
td (off) tf
Turn- off transient
–Turn- off delay time td(off)
–Falling time tf
t
Examples of commercial power MOSFET
part number Rated max voltage Rated vag current
Ron
IRFZ48
IRF510
IRF540
APT105M25BN
R IRF740
MTM15N40E
APT5025BN
0.018Ω
0.54Ω
0.077Ω
0.025Ω
0.55Ω
0.3Ω
0.25Ω
1.0Ω
APT1001RBNR
60V
100V
100V
100V
400V
400V
500V
1000V
50A
5.6A
28A
75A
10A
15A
23A
11A
Qg(typical)
110nC
8.3 nC
72 nC
171 nC
63 nC
8.3
nC
110 nC
83nC
150 nC
1.4.4 Insulated- gate bipolar transistor—IGBT

Combination of MOSFET and GTR
GTR: low conduction losses (especially at larger blocking volta ges),
longer switching times, current- driven
IGBT
MOSFET : faster switching speed, easy to drive (voltage- driven),
larger conduction losses (especially for higher blocking voltages)
Features
On- state losses are much smaller than
those of a power MOSFET, and are
comparable with those of a GTR
Easy to drive —similar to power
MOSFET
Faster than GTR, but slower than power
MOSFET

Structure and operation principle of
IGBT
Also multiple cell structure Basic structure
similar to power MOSFET, except extra
p region On- state: minority carriers
are injected into drift region, leading to
conductivity modulation
compared with power MOSFET: slower
switching times, lower on- resistance,
useful at higher voltages (up to 1700V)

Emitter Gate
G
E
N+ P N+ N+ P N+
J3 J2 NN+
+
J1 P
C Collector
Drift region
Buffer layer
Injecting layer

Equivalent circuit and circuit symbol of IGBT
+
V
J1
R
ID N
- Drift region
+G
+ resistance
IDRon
E
C
IC
C
G
E

Switching characteristics of IGBT
UGE
90%UGEM
10%UGEM
0
IC
90%ICM
UGEM
t
ICM
td(on) t r
td(off)
tf
t fi1 t fi2
10%ICM
0
UCE
current tail
ton
toff
UCEM
t fv1
t
t fv2
UCE（on）
0
t

Examples of commercial IGBT
part number Rated max voltage Rated avg current VF(typical tf(typical)
Single-chip devices
600V
HGTG32N60E2
1200V
HGTG30N120D2
multiple-chip power modules_
600V
CM400HA-12E
1200V
CM300HA-24E
32A
30A
400A
300A
)
2.4V
3.2V
0.62μs
0.58μs
2.7V
2.7V
0.3μs
0.3μs
8.3 nC
1.5 Other new power electronic devices
Static induction transistor —SIT
Static induction thyristor —SITH
MOS controlled thyristor —MCT
Integrated gate- commutated thyristor —IGCT
Power integrated circuit and power module
1)
Static induction transistor—SIT
Another name: power junction field effect transistor—power JFET Features
–Major- carrier device
–Fast switching, comparable to power MOSFET
–Higher power- handling capability than power MOSFET
–Higher conduction losses than power MOSFET
–Normally- on device, not convenient (could be made normally- off, but with
even higher on-state losses)
2) Static induction thyristor—SITH
other names
–Field controlled thyristor—FCT
–Field controlled diode
Features
–Minority- carrier device, a JFET structure with an additional
injecting layer
–Power- handling capability similar to GTO
–Faster switching speeds than GTO
–Normally- on device, not convenient (could be made
normally- off, but with even higher on- state losses)
3) MOS controlled thyristor—MCT
Essentially a GTO with integrated MOS- driven gates controlling both
turn- on and turn- off that potentially will significantly simply the
design of circuits using GTO.
The difficulty is how to design a MCT that can be turned on and turned
off equally well.
Once believed as the most promising device, but still not commercialized
in a large scale. The future remains uncertain.
4) Integrated gate- commutated thyristor — IGCT
The newest member of the power semiconductor family, introduced in
1997 by ABB
Actually the close integration of GTO and the gate drive circuit with
multiple MOSFETs in parallel providing the gate currents
Short name: GCT
Conduction drop, gate driver loss, and switching speed are superior to
GTO
Competing with IGBT and other new devices to replace GTO

Review of device classifications
power electronic
devices
Current- driven (current- controlled) devices:
thyristor, GTO, GTR
Voltage- driven (voltage- controlled) devices
(Field- controlled devices):power MOSFET,IGBT,
SIT, SITH, MCT, IGCT
Pulse- triggered devices: thyristor, GTO
power electronic
devices
Level- sensitive (Level- triggered) devices:
GTR, power MOSFET, IGBT, SIT, SITH,MCT, IGCT
Uni- polar devices (Majority carrier devices):
SBD, power MOSFET, SIT
power electronic
devices
Bipolar devices (Minority carrier devices):
ordinary power diode, thyristor, , GTO, GTR,
IGCT, IGBT, SITH, MCT
Composite devices: IGBT, SITH, MCT