Transcript PI5USB2546

Power wake : PI5USB2543 vs PI5USB2546/A
 PI5USB2543
 PI5USB2546/A
Didn’t support Power wake
feature
 With current sensing and

Will detect Vbus current
>0.1mA as for plugged-in

Will detect Vbus current
>55mA as for plugged-in

Will detect certain D+/voltage as plugged-out.

Will detect Vbus current
<45mA as plugged-out.

behavior same as TPS2546
(please refer to P.23 to P27 for details)
1
Confidential
Copyright Pericom Semiconductor Corp 2013
PI5USB2546/A Power Wake in Notebook
 Power wake is activated in S4 / S5 mode of the system
 CTL1/2/3 & ILIM_SEL = 0011
 Select between high power DC-DC converter or low
power LDO based on charging requirements
2
Confidential
Copyright Pericom Semiconductor Corp 2012
PI5USB2546/A Power Wake in notebook
 When device is connected to the charging port and
provide charging current > 55mA (typ),
 STATUS# will pull “LOW” => the power supplier of the
charging port will be switched out from LDO and to
DC-DC converter
 VBUS turn off for 2s
 Current limit auto switch to ILIM_HI => (depends on
the RILIM_HI - Pin 16 of PI5USB2546/A)
3
Confidential
Copyright Pericom Semiconductor Corp 2012
PI5USB2546/A Power Wake in notebook
Power Block
PI5USB2546/A
19V
CTL1
CTL2
CLT3
ILIM_SEL
0
0
1
1
I > 55mA
5V DC-DC
IN
OUT
VBUS
5V LDO
EN#
/STATUS = L
Embedded
Controller
D-_IN
D-
D+_IN
D+
STATUS#
GND
GND
CTL1
CTL2
CTL3
ILIM_SEL
D±
OC#
D±OUT
ILIM_HI
FAULT#
ILIM_LO
USB Host
Controller
4
Confidential
Current limit
change to
ILIM_HI
Copyright Pericom Semiconductor Corp 2012
PI5USB2546/A Power Wake in Notebook
 When device is unplugged or device is fully charge
and current is drop to < 45mA (typ),
 STATUS# of PI5USB2546 will pull “HIGH” after 15s =>
control the low power LDO supplies the standby
power of the charging port.
 Current limit set to internally => 55mA for LDO
5
Confidential
Copyright Pericom Semiconductor Corp 2012
Power Wake in notebook
Power Block
PI5USB2546/A
19V
CTL1
CTL2
CLT3
ILIM_SEL
0
0
1
1
I < 45mA
5V DC-DC
IN
OUT
VBUS
5V LDO
EN#
/STATUS = H
After 15s
Embedded
Controller
D-_IN
D-
D+_IN
D+
STATUS#
GND
Device is un-plugged
or Device is fully
charged
GND
CTL1
CTL2
CTL3
Internal current
limit (55mA)
ILIM_SEL
D±
OC#
D±OUT
ILIM_HI
FAULT#
ILIM_LO
USB Host
Controller
6
Confidential
Copyright Pericom Semiconductor Corp 2012
PI5USB2546/A Port Power Management (PPM)
 PPM is activated in S0 (CDP) or S3 - S5 (DCP_Auto)
mode of the system
 CTL1/2/3 & ILIM_SEL = 1111 or 0111
 Prevents overloading of the system’s power supply
 Limiting the total power of USB port
 System monitors /STATUS pin for different USB port
 Once # of USB port assert /STATUS, system will
toggle the reminding port to a SDP
 If the charging current drop to < ILIM_LO + 60mA,
/STATUS pin will de-assert and system resume the
charging feature for all USB ports.
7
Confidential
Copyright Pericom Semiconductor Corp 2013
PPM in notebook
/STATUS =
High
Embedded
Controller
STATUS#
USB signal
CTL1
CTL2
CTL2
CLT3
ILIM_SEL
1
1
1
1
0
1
1
1
USB port 1
PI5USB2546 – U1
CTL1
ILIM_HI
CTL3
ILIM_LO
PI5USB2546 – U2
/STATUS = High
D±
STATUS#
OC#
CTL1
CTL2
USB Host
Controller
CTL3
ILIM_HI
USB signal
USB port 2
ILIM_SEL
ILIM_LO
ILIM_HI
ILIM_LO
If current draw <
ILIM_LO + 60mA
ILIM_SEL
Remark: USB signal including Vbus, D+, D- and GND signal
8
Confidential
Copyright Pericom Semiconductor Corp 2012
PPM in notebook
/STATUS =
High
Embedded
Controller
STATUS#
USB signal
CTL1
CTL2
CTL2
CLT3
ILIM_SEL
1
1
1
1
0
1
1
1
USB port 1
PI5USB2546 – U1
CTL1
ILIM_HI
ILIM_LO
ILIM_SEL
Change CTL1/2/3
& ILIM_SEL to
SDP
Current limit
changed to
ILIM_LO
PI5USB2546 – U2
/STATUS = Low
D±
STATUS#
OC#
CTL1
CTL2
USB Host
Controller
CTL3
ILIM_HI
USB signal
USB port 2
CTL3
ILIM_LO
ILIM_HI
ILIM_LO
If current draw >
ILIM_LO + 60mA
ILIM_SEL
Remark: USB signal including Vbus, D+, D- and GND signal
9
Confidential
Copyright Pericom Semiconductor Corp 2012