Transcript Chapter 30
Chapter 30
Nuclear Energy
and
Elementary Particles
Processes of Nuclear Energy
Fission
Fusion
A nucleus of large mass number splits into
two smaller nuclei
Two light nuclei fuse to form a heavier
nucleus
Large amounts of energy are released
in either case
Nuclear Fission
A heavy nucleus splits into two smaller
nuclei
The total mass of the products is less than
the original mass of the heavy nucleus
First observed in 1939 by Otto Hahn and
Fritz Strassman following basic studies by
Fermi
Lisa Meitner and Otto Frisch soon
explained what had happened
Fission Equation
Fission of
neutron
235U
by a slow (low energy)
236
n 235
U
92
92 U* X Y neutrons
1
0
236U*
is an intermediate, short-lived state
X and Y are called fission fragments
Many combinations of X and Y satisfy the
requirements of conservation of energy and
charge
Sequence of Events in Fission
The 235U nucleus captures a thermal (slowmoving) neutron
This capture results in the formation of 236U*,
and the excess energy of this nucleus causes
it to undergo violent oscillations
The 236U* nucleus becomes highly elongated,
and the force of repulsion between the
protons tends to increase the distortion
The nucleus splits into two fragments,
emitting several neutrons in the process
Sequence of Events in Fission
– Diagram
Energy in a Fission Process
Binding energy for heavy nuclei is about 7.2
MeV per nucleon
Binding energy for intermediate nuclei is
about 8.2 MeV per nucleon
Therefore, the fission fragments have less
mass than the nucleons in the original nuclei
This decrease in mass per nucleon appears as
released energy in the fission event
Energy, cont
An estimate of the energy released
Assume a total of 240 nucleons
Releases about 1 MeV per nucleon
8.2 MeV – 7.2 MeV
Total energy released is about 240 Mev
This is very large compared to the
amount of energy released in chemical
processes
QUICK QUIZ 30.1
In the first atomic bomb, the energy released
was equivalent to about 30 kilotons of TNT,
where a ton of TNT releases an energy of
4.0 × 109 J. The amount of mass converted
into energy in this event is nearest to: (a) 1
g, (b) 1 mg, (c) 1 g, (d) 1 kg, (e) 20
kilotons
QUICK QUIZ 30.1 ANSWER
(c). The total energy released was E = (30
×103 ton)(4.0 × 109 J/ton) = 1.2 × 1014 J.
The mass equivalent of this quantity of
energy is:
E
1.2 1014 J
3
m 2
1.3 10 kg ~ 1g
8
2
c
(3.0 10 m/s)
Chain Reaction
Neutrons are emitted when 235U undergoes
fission
These neutrons are then available to trigger
fission in other nuclei
This process is called a chain reaction
If uncontrolled, a violent explosion can occur
The principle behind the nuclear bomb, where 1 g
of U can release energy equal to about 20000 tons
of TNT
Chain Reaction – Diagram
Nuclear Reactor
A nuclear reactor is a system designed to
maintain a self-sustained chain reaction
The reproduction constant, K, is defined as
the average number of neutrons from each
fission event that will cause another fission
event
The maximum value of K from uranium fission is
2.5
In practice, K is less than this
A self-sustained reaction has K = 1
K Values
When K = 1, the reactor is said to be critical
When K < 1, the reactor is said to be
subcritical
The chain reaction is self-sustaining
The reaction dies out
When K > 1, the reactor is said to be
supercritical
A run-away chain reaction occurs
Basic Reactor Design
Fuel elements
consist of enriched
uranium
The moderator
material helps to
slow down the
neutrons
The control rods
absorb neutrons
Reactor Design Considerations
– Neutron Leakage
Loss (or “leakage”) of neutrons from
the core
These are not available to cause fission
events
The fraction lost is a function of the
ratio of surface area to volume
Small reactors have larger percentages lost
If too many neutrons are lost, the reactor
will not be able to operate
Reactor Design Considerations
– Neutron Energies
Slow neutrons are more likely to cause fission
events
Most neutrons released in the fission process
have energies of about 2 MeV
In order to sustain the chain reaction, the
neutrons must be slowed down
A moderator surrounds the fuel
Collisions with the atoms of the moderator slow
the neutrons down as some kinetic energy is
transferred
Most modern reactors use heavy water as the
moderator
Reactor Design Considerations
– Neutron Capture
Neutrons may be captured by nuclei
that do not undergo fission
Most commonly, neutrons are captured by
238U
The possibility of 238U capture is lower with
slow neutrons
The moderator helps minimize the
capture of neutrons by 238U
Reactor Design Considerations
– Power Level Control
A method of control is needed to adjust the value
of K to near 1
Control rods are inserted into the core to control
the power level
Control rods are made of materials that are very
efficient at absorbing neutrons
If K >1, the heat produced in the runaway reaction can
melt the reactor
Cadmium is an example
By adjusting the number and position of the
control rods, various power levels can be
maintained
Pressurized Water Reactor –
Diagram
Pressurized Water Reactor –
Notes
This type of reactor is commonly used in
electric power plants in the US
Fission events in the reactor core supply heat
to the water contained in the primary system
The primary system is a closed system
This water is maintained at a high pressure to
keep it from boiling
The hot water is pumped through a heat
exchanger
Pressurized Water Reactor –
Notes, cont
The heat is transferred to the water
contained in a secondary system
This water is converted into steam
The steam is used to drive a turbinegenerator to create electric power
The water in the secondary system is isolated
from the water in the primary system
This prevents contamination of the secondary
water and steam by the radioactive nuclei in the
core
Reactor Safety – Containment
Radiation exposure, and its potential health
risks, are controlled by three levels of
containment
Reactor vessel
Reactor building
Contains the fuel and radioactive fission products
Acts as a second containment structure should the
reactor vessel rupture
Location
Reactor facilities are in remote locations
Reactor Safety – Loss of
Water
If the water flow was interrupted, the nuclear
reaction could stop immediately
However, there could be enough residual heat to
build up and melt the fuel elements
The molten core could also melt through the containment
vessel and into the ground
Called the China Syndrome
If the molten core struck ground water, a steam explosion
could spread the radioactive material to areas surrounding
the power plant
Reactors are built with emergency cooling
systems that automatically flood the core if
coolant is lost
Reactor Safety – Radioactive
Materials
Disposal of waste material
Waste material contains long-lived, highly radioactive
isotopes
Must be stored over long periods in ways that protect the
environment
Present solution is sealing the waste in waterproof
containers and burying them in deep salt mines
Transportation of fuel and wastes
Accidents during transportation could expose the public to
harmful levels of radiation
Department of Energy requires crash tests and
manufacturers must demonstrate that their containers will
not rupture during high speed collisions
Nuclear Fusion
Nuclear fusion occurs when two light
nuclei combine to form a heavier
nucleus
The mass of the final nucleus is less
than the masses of the original nuclei
This loss of mass is accompanied by a
release of energy
Fusion in the Sun
All stars generate energy through fusion
The Sun, along with about 90% of other
stars, fuses hydrogen
Some stars fuse heavier elements
Two conditions must be met before fusion
can occur in a star
The temperature must be high enough
The density of the nuclei must be high enough to
ensure a high rate of collisions
Proton-Proton Cycle
1
1
2
The proton-proton
H
H
H
e
1
1
1
cycle is a series of
1
2
3
three nuclear
1H 1H 2 He
reactions believed to
Then
operate in the Sun
1
3
4
Energy liberated is
1H 2 He 2 He e
primarily in the form
or
of gamma rays,
positrons and
3
3
4
1
1
2 He 2 He 2 He 1H1H
neutrinos
Fusion Reactors
Energy releasing fusion reactions are
called thermonuclear fusion reactions
A great deal of effort is being directed
at developing a sustained and
controllable thermonuclear reaction
A thermonuclear reactor that can
deliver a net power output over a
reasonable time interval is not yet a
reality
Advantages of a Fusion
Reactor
Inexpensive fuel source
Water is the ultimate fuel source
If deuterium is used as fuel, 0.06 g of it
can be extracted from 1 gal of water for
about 4 cents
Comparitively few radioactive byproducts are formed
Considerations for a Fusion
Reactor
The proton-proton cycle is not feasible for a
fusion reactor
The high temperature and density required
are not suitable for a fusion reactor
The most promising reactions involve
deutrium and tritium
2
2
3
1
H
H
H
1
1
2
0 n Q 3.27 MeV
H H H H Q 4.03 MeV
2
1
2
1
3
1
1
1
H H He n
2
1
3
1
4
3
1
0
Q 17.59 MeV
Considerations for a Fusion
Reactor, cont
Tritium is radioactive and must be
produced artifically
The Coulomb repulsion between two
charged nuclei must be overcome
before they can fuse
Requirements for Successful
Thermonuclear Reactor
High temperature ~ 108 K
Plasma ion density, n
Needed to give nuclei enough energy to overcome
Coulomb forces
At these temperatures, the atoms are ionized,
forming a plasma
The number of ions present
Plasma confinement time,
The time the interacting ions are maintained at a
temperature equal to or greater than that required
for the reaction to proceed successfully
Lawson’s Criteria
Lawson’s criteria states that a net
power output in a fusion reactor is
possible under the following conditions
n 1014 s/cm3 for deuterium-tritium
n 1016 s/cm3 for deuterium-deuterium
The plasma confinement time is still a
problem
Magnetic Confinement
One magnetic confinement
device is called a tokamak
Two magnetic fields confine
the plasma inside the
doughnut
A strong magnetic field is
produced in the windings
A weak magnetic field is
produced in the toroid
The field lines are helical,
spiral around the plasma,
and prevent it from touching
the wall of the vacuum
chamber
Current Research in Fusion
Reactors
NSTX – National Spherical Torus Experiment
Produces a spherical plasma with a hole in the
center
Is able to confine the plasma with a high pressure
ITER – International Thermonuclear
Experimental Reactor
An international collaboration involving four major
fusion programs is working on building this reactor
It will address remaining technological and
scientific issues concerning the feasibility of fusion
power
Elementary Particles
Atoms
From the Greek for “indivisible”
Were once thought to the elementary
particles
Atom constituents
Proton, neutron, and electron
Were viewed as elementary because they
are very stable
Discovery of New Particles
New particles
Beginning in 1937, many new particles
were discovered in experiments involving
high-energy collisions
Characteristically unstable with short
lifetimes
Over 300 have been cataloged
A pattern was needed to understand all
these new particles
Quarks
Physicists recognize that most particles are
made up of quarks
Exceptions include photons, electrons and a few
others
The quark model has reduced the array of
particles to a manageable few
The quark model has successfully predicted
new quark combinations that were
subsequently found in many experiments
Fundamental Forces
All particles in nature are subject to four
fundamental forces
Strong force
Electromagnetic force
Weak force
Gravitational force
Strong Force
Is responsible for the tight binding of the
quarks to form neutrons and protons
Also responsible for the nuclear force binding
the neutrons and the protons together in the
nucleus
Strongest of all the fundamental forces
Very short-ranged
Less than 10-15 m
Electromagnetic Force
Is responsible for the binding of atoms
and molecules
About 10-2 times the strength of the
strong force
A long-range force that decreases in
strength as the inverse square of the
separation between interacting particles
Weak Force
Is responsible for instability in certain nuclei
Is responsible for beta decay
A short-ranged force
Its strength is about 10-6 times that of the
strong force
Scientists now believe the weak and
electromagnetic forces are two manifestions
of a single force, the electroweak force
Gravitational Force
A familiar force that holds the planets,
stars and galaxies together
Its effect on elementary particles is
negligible
A long-range force
It is about 10-43 times the strength of
the strong force
Weakest of the four fundamental forces
Explanation of Forces
Forces between particles are often
described in terms of the actions of field
particles or quanta
For electromagnetic force, the photon is
the field particle
The electromagnetic force is mediated, or
carried, by photons
Forces and Mediating Particles
(also see table 30.1)
Interaction (force)
Mediating Field Particle
Strong
Gluon
Electromagnetic
Photon
Weak
W and Z0
Gravitational
Gravitons
Antiparticles
For every particle, there is an antiparticle
An antiparticle has the same mass as the particle, but
the opposite charge
The positron (electron’s antiparticle) was discovered
by Anderson in 1932
From Dirac’s version of quantum mechanics that
incorporated special relativity
Since then, it has been observed in numerous experiments
Practically every known elementary particle has a
distinct antiparticle
Exceptions – the photon and the neutral pi particles are their
own antiparticles
Mesons
Developed from a theory to explain the
strong nuclear force
Background notes
Two atoms can form a covalent bond by the
exchange of electrons
In electromagnetic interactions, charged particles
interact by exchanging a photon
A new particle was proposed to explain the
strong nuclear force
It was called a meson
Mesons, cont
The proposed particle would have a mass
about 200 times that of the electron
Efforts to establish the existance of the
particle were done by studying cosmic rays in
the 1930’s
Actually discovered multiple particles
Pi meson (pion)
Muon
Not a meson
Pion
There are three varieties of pions
+ and
0
Mass of 139.6 MeV/c2
Mass of 135.0 MeV/c2
Pions are very unstable
- decays into a muon and an antineutrino
with a lifetime of about 2.6 x10-8 s
Feynman Diagrams
A graphical representation of the
interaction between two particles
Feynman diagrams are named for
Richard Feynman who developed them
Feynman Diagram – Two
Electrons
The photon is the field
particle that mediates the
interaction
The photon transfers energy
and momentum from one
electron to the other
The photon is called a
virtual photon
It can never be detected
directly because it is absorbed
by the second electron very
shortly after being emitted by
the first electron
The Virtual Photon
The existance of the virtual photon
would violate the law of conservation of
energy
But, due to the uncertainty principle and its
very short lifetime, the photon’s excess
energy is less than the uncertainty in its
energy
The virtual photon can exist for short time
intervals, such that ΔE~ / Δt
Feynman Diagram – Proton
and Neutron
The exchange is via the
nuclear force
The existance of the pion is
allowed in spite of
conservation of energy if this
energy is surrendered in a
short enough time
Analysis predicts the rest
energy of the pion to be 130
MeV / c2
This is in close agreement
with experimental results
Classification of Particles
Two board categories
Classified by interactions
Hadrons – interact through strong force
Leptons – interact through weak force
Hadrons
Interact through the strong force
Two subclasses
Mesons
Baryons
Decay finally into electrons, positrons, neutrinos and
photons
Integer spins
Masses equal to or greater than a proton
Noninteger spin values
Decay into end products that include a proton (except for
the proton)
Composed of quarks
Leptons
Interact through weak force
All have spin of ½
Leptons appear truly elementary
No substructure
Point-like particles
Scientists currently believe only six leptons
exist, along with their antiparticles
Electron and electron neutrino
Muon and its neutrino
Tau and its neutrino
Conservation Laws
A number of conservation laws are
important in the study of elementary
particles
Two new ones are
Conservation of Baryon Number
Conservation of Lepton Number
Conservation of Baryon
Number
Whenever a baryon is created in a reaction or
a decay, an antibaryon is also created
B is the Baryon Number
B = +1 for baryons
B = -1 for antibaryons
B = 0 for all other particles
The sum of the baryon numbers before a
reaction or a decay must equal the sum of
baryon numbers after the process
Conservation of Lepton
Number
There are three conservation laws, one
for each variety of lepton
Law of Conservation of Electron-Lepton
Number states that the sum of electronlepton numbers before a reaction or a
decay must equal the sum of the
electron-lepton number after the
process
Conservation of Lepton
Number, cont
Assigning electron-lepton numbers
Le = 1 for the electron and the electron neutrino
Le = -1 for the positron and the electron
antineutrino
Le = 0 for all other particles
Similarly, when a process involves muons,
muon-lepton number must be conserved and
when a process involves tau particles, taulepton numbers must be conserved
Muon- and tau-lepton numbers are assigned
similarly to electron-lepton numbers
QUICK QUIZ 30.2
Which of the following reactions cannot occur?
( b) n p e v e
(c) e v e v (d) v
QUICK QUIZ 30.2 ANSWER
(a). This reaction fails to conserve charge and
cannot occur.
QUICK QUIZ 30.3
Which of the following reactions cannot occur?
(a) p p 2
(b) p n
0
(c) n K
0
(d) p K
QUICK QUIZ 30.3 ANSWER
(b). This reaction fails to conserve charge
and cannot occur.
QUICK QUIZ 30.4
Suppose a claim is made that the
decay
of
a
_
+
neutron is given by n p + e . Which of
the following conservation laws are
violated by this proposed decay scheme?
(a) energy, (b) linear momentum, (c) spin
angular momentum, (d) electric charge, (e)
lepton number, (f) baryon number.
QUICK QUIZ 30.4 ANSWER
(c), (e). The proton and the electron each
have spin s = ½ . The two possible resultant
spins after decay are 1 (spins aligned) or 0
(spins anti-aligned). Neither equal the spin of
a neutron, s = ½ , so spin angular momentum
is not conserved. The are no leptons present
before the proposed decay and one lepton
(the electron) present after decay. Thus, the
decay also fails to conserve lepton number.
Strange Particles
Some particles discovered in the 1950’s were
found to exhibit unusual properties in their
production and decay and were given the
name strange particles
Peculiar features include
Always produced in pairs
Although produced by the strong interaction, they
do not decay into particles that interact via the
strong interaction, but instead into particles that
interact via weak interactions
They decay much more slowly than particles decaying
via strong interactions
Strangeness
To explain these unusual properties, a new
law, the conservation of strangeness was
introduced
Also needed a new quantum number, S
The Law of Conservation of Strangeness states
that the sum of strangeness numbers before a
reaction or a decay must equal the sum of the
strangeness numbers after the process
Strong and electromagnetic interactions obey
the law of conservation of strangeness, but
the weak interaction does not
Bubble Chamber
Example
The dashed lines
represent neutral
particles
At the bottom,
- + p Λ0 + K0
Then Λ0 - + p
and
K0 + µ- + µ
The Eightfold Way
Many classification schemes have been
proposed to group particles into families
These schemes are based on spin, baryon number,
strangeness, etc.
The eightfold way is a symmetic pattern
proposed by Gell-Mann and Ne’eman
There are many symmetrical patterns that
can be developed
The patterns of the eightfold way have much
in common with the periodic table
Including predicting missing particles
An Eightfold Way for Baryons
A hexagonal pattern for
the eight spin ½
baryons
Stangeness vs. charge
is plotted on a sloping
coordinate system
Six of the baryons form
a hexagon with the
other two particles at its
center
An Eightfold Way for Mesons
The mesons with spins of
0 can be plotted
Strangeness vs. charge on
a sloping coordinate
system is plotted
A hexagonal pattern
emerges
The particles and their
antiparticles are on
opposite sides on the
perimeter of the hexagon
The remaining three
mesons are at the center
Quarks
Hadrons are complex particles with size
and structure
Hadrons decay into other hadrons
There are many different hadrons
Quarks are proposed as the elementary
particles that constitute the hadrons
Originally proposed independently by GellMann and Zweig
Original Quark Model
Three types
Associated with each quark is an antiquark
The antiquark has opposite charge, baryon
number and strangeness
Quarks have fractional electrical charges
u – up
d – down
s – originally sideways, now strange
+1/3 e and –2/3 e
All ordinary matter consists of just u and d
quarks
Original Quark Model – Rules
All the hadrons at the time of the
original proposal were explained by
three rules
Mesons consist of one quark and one
antiquark
This gives them a baryon number of 0
Baryons consist of three quarks
Antibaryons consist of three antiquarks
Additions to the Original
Quark Model – Charm
Another quark was needed to account for
some discrepencies between predictions of
the model and experimental results
Charm would be conserved in strong and
electromagnetic interactions, but not in weak
interactions
In 1974, a new meson, the J/Ψ was
discovered that was shown to be a charm
quark and charm antiquark pair
More Additions – Top and
Bottom
Discovery led to the need for a more
elaborate quark model
This need led to the proposal of two new
quarks
t – top (or truth)
b – bottom (or beauty)
Added quantum numbers of topness and
bottomness
Verification
b quark was found in a Y meson in 1977
t quark was found in 1995 at Fermilab
Numbers of Particles
At the present, physicists believe the
“building blocks” of matter are complete
Six quarks with their antiparticles
Six leptons with their antiparticles
Color
Isolated quarks
Physicist now believe that quarks are
permanently confined inside ordinary
particles
No isolated quarks have been observed
experimentally
The explanation is a force called the color
force
Color force increases with increasing distance
This prevents the quarks from becoming
isolated particles
Colored Quarks
Color “charge” occurs in red, blue, or
green
Antiquarks have colors of antired, antiblue,
or antigreen
Color obeys the Exclusion Principle
A combination of quarks of each color
produces white (or colorless)
Baryons and mesons are always
colorless
Quark Structure of a Meson
A red quark is
attracted to an
antired quark
The quark –
antiquark pair forms
a meson
The resulting meson
is colorless
Quark Structure of a Baryon
Quarks of different
colors attract each
other
The quark triplet
forms a baryon
The baryon is
colorless
Quantum Chromodynamics
(QCD)
QCD gave a new theory of how quarks
interact with each other by means of color
charge
The strong force between quarks is often
called the color force
The strong force between quarks is carried by
gluons
Gluons are massless particles
There are 8 gluons, all with color charge
When a quark emits or absorbs a gluon, its
color changes
More About Color Charge
Like colors repel and unlike colors attract
Different colors attract, but not as strongly as a
color and its anticolor
The color force between color-neutral
hadrons is negligible at large separations
The strong color force between the constituent
quarks does not exactly cancel at small
separations
This residual strong force is the nuclear force that
binds the protons and neutrons to form nuclei
QCD Explanation of a
Neutron-Proton Interaction
Each quark within the
proton and neutron is
continually emitting and
absorbing virtual gluons
Also creating and
annihilating virtual
quark-antiquark pairs
When close enough,
these virtual gluons and
quarks can be
exchanged, producing
the strong force
Weak Interaction
The weak interaction is an extremely shortranged force
This short range implies the mediating particles
are very massive
The weak interaction is responsible for the
decay of c, s, b, and t quarks into u and d
quarks
Also responsible for the decay of and
leptons into electrons
Weak Interaction, cont
The weak interaction is very important
because it governs the stability of the
basic matter particles
The weak interaction is not symmetrical
Not symmetrical under mirror reflection
Not symmetrical under charge exchange
Electroweak Theory
The electroweak theory unifies
electromagnetic and weak interactions
The theory postulates that the weak
and electromagnetic interactions have
the strength at very high particle
energies
Viewed as two different manifestions of a
single interaction
The Standard Model
A combination of the electroweak theory and
QCD form the standard model
Essential ingredients of the standard model
The strong force, mediated by gluons, holds the
quarks together to form composite particles
Leptons participate only in electromagnetic and
weak interactions
The electromagnetic force is mediated by photons
The weak force is mediated by W and Z bosons
The Standard Model – Chart
Mediator Masses
Why does the photon have no mass while
the W and Z bosons do have mass?
Not answered by the Standard Model
The difference in behavior between low and
high energies is called symmetry breaking
The Higgs boson has been proposed to
account for the masses
Large colliders are necessary to achieve the energy
needed to find the Higgs boson
Grand Unification Theory
(GUT)
Builds on the success of the
electroweak theory
Attempted to combine electroweak and
strong interactions
One version considers leptons and quarks
as members of the same family
They are able to change into each other by
exchanging an appropriate particle
The Big Bang
This theory of cosmology states that during
the first few minutes after the creation of the
universe all four interactions were unified
All matter was contained in a quark soup
As time increased and temperature
decreased, the forces broke apart
Starting as a radiation dominated universe, as
the universe cooled it changed to a matter
dominated universe
A Brief History of the Universe
Cosmic Background Radiation
(CBR)
CBR is represents the
cosmic “glow” left over
from the Big Bang
The radiation had equal
strengths in all directions
The curve fits a blackbody
at ~3K
There are small
irregularities that allowed
for the formation of
galaxies and other objects
Connection Between Particle
Physics and Cosmology
Observations of events that occur when
two particles collide in an accelerator
are essential to understanding the early
moments of cosmic history
There are many common goals between
the two fields
Some Questions
Why so little antimatter in the Universe?
Do neutrinos have mass?
Is it possible to unify electroweak and strong
forces?
Why do quark and leptons form similar but
distinct families?
Why do quarks carry fractional charge?
What determines the masses of fundamental
particles?
Do leptons and quarks have a substructure?