Transcript 05_E-FIBx
Eclipse HX E-FIB Fibre card Eclipse HX E-FIB CARD E-FIB – FIBRE NETWORKING CARD Dual redundant optical transceivers for networking matrices together to form a fibre optic ring. The fibre ring provides 1024 audio channels shared across all linked matrices (15 matrices in total) in the ring. The Fibre ring carries audio only. Matrix to Matrix data is carried separately using a LAN The system also provides automatic switchover from ring A to ring B and Auto loopback in case of any breaks in the ring Two cards can be placed in a matrix to provide card redundancy as well ring redundancy Matrix B, Matrix A, Ethernet data Eclipse HX E-FIB CARD E-FIB – STATUS LEDS A failure on transceiver A then the card switches automatically to transceiver B The card status LED flashes to indicate which card is master and receiving audio Transceiver LEDs on a fibre card which is correctly wired and running on Ring A Eclipse HX E-FIB CARD E-FIB – REAR CARD RX Laser TX Laser Eye Safety !!! This laser based single mode transceiver is a Class 1 product. It complies with IEC 608251/A2: 2001 and FDA performance standards for laser products (21 CFR 1040.10 and 1040.11) except for deviations pursuant to Laser Notice 50, dated July 26, 2001. Eclipse HX E-FIB CARD E-FIB – FIBRE CONNECTION Wire up the matrices following the HX system numbers with the LOWEST IP address as system 1 / node 1, For primary ring A wire from system 1 > system 2 > system 3 etc.. For redundant ring B wire from system 3 > system 2 > system 1 Eclipse HX E-FIB CARD Eclipse HX E-FIB CARD E-FIB – FIBRE CONNECTION TX2-FIBRE CARD#1 RX2 TX2-FIBRE CARD#1 RX2 TX2-FIBRE CARD#1 RX2 RX1-FIBRE CARD#1 TX1 RX1-FIBRE CARD#1 TX1 RX1-FIBRE CARD#1 TX1 TX1-FIBRE CARD#1 RX1 TX1-FIBRE CARD#1 RX1 RX2-FIBRE CARD#1 TX2 RX2-FIBRE CARD#1 TX2 MAIN FIBRE RING SECOND FIBRE RING EACH FIBRE CARD HAS 2 FIBRE TRANSCEIVERS THE CONNECTOR TYPE IS - DUPLEX LC TX1/RX1 IS USED FOR THE MAIN RING TX2/RX2 IS USED FOR SECOND RING USE SINGLE MODE FIBRE 9/125 Eclipse HX E-FIB CARD E-FIB – HX FIBRE SETUP To configure a fibre network the following rules have to be followed ► Declare the fibre cards in HX for each matrix ► Wire up the matrices following the HX system numbers with the LOWEST IP address as system 1 / node 1 ► For primary ring A wire from system 1 > system 2 > system 3 etc.. ► For redundant ring B wire from system 3 > system 2 > system 1 HX allows each E-FIB (matrix) card to set a port count for the number of audio channels to be allocated to the matrix (trunk lines). Different matrices can be set different port counts (trunk lines). A max of 192 trunks per matrix can be set The general recommendation for the E-FIB count port ► If the network is below 5x matrices set all port counts to the maximum 192 port count ► As the network grows above 6x matrices trailer the port count per matrix using the trunk usage messages from matrix event log. Eclipse HX E-FIB CARD E-FIB – HX FIBRE SETUP Link the Fibre cards together in the “layout” screen Eclipse HX E-FIB CARD E-FIB – FIBRE CABLING Primary Fibre Ring from A >B > C > D Redundant Fibre Ring from D>C>B>A Matrix A, Matrix B, Matrix D, Matrix C, Eclipse HX E-FIB CARD E-FIB – SELF HEALING & LOOPBACK Matrix A, Matrix B, Primary Fibre Ring Redundant Fibre Ring Loopback ► ► ► Matrix D, A break on the Main primary Fibre Ring System switches to Backup redundant ring A Break on the backup ring – system now goes into LOOP- BACK and the system will heal it self and make best use of the fibre links that are intact Matrix C, Eclipse HX E-FIB CARD E-FIB – SELF HEALING & LOOPBACK Matrix A, Matrix B, In this example – the system has formed into two small islands Matrix D, Matrix C, Thank you!