Transcript 3rd Edition: Chapter 4

Chapter 4: Network Layer
Chapter goals:
 Understand principles behind network layer
services:
Routing (path selection)
 dealing with scale
 how a router works
 advanced topics: IPv6, mobility

 instantiation and implementation in the
Internet
Network Layer
4-1
Chapter 4: Network Layer
 4. 1 Introduction
 4.2 Virtual circuit and
datagram networks
 4.3 What’s inside a
router
 4.4 IP: Internet
Protocol




Datagram format
IPv4 addressing
ICMP
IPv6
 4.5 Routing algorithms
 Link state
 Distance Vector
 Hierarchical routing
 4.6 Routing in the
Internet



RIP
OSPF
BGP
 4.7 Broadcast and
multicast routing
Network Layer
4-2
Network layer functions
 transport packet from
sending to receiving hosts
 network layer protocols in
every host, router
three important functions:
 path determination: route
taken by packets from source
to dest. Routing algorithms
 forwarding: move packets
from router’s input to
appropriate router output
 call setup: some network
architectures require router
call setup along path before
data flows
application
transport
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
application
transport
network
data link
physical
Network Layer
4-3
Interplay between routing and forwarding
routing algorithm
local forwarding table
header value output link
0100
0101
0111
1001
3
2
2
1
value in arriving
packet’s header
0111
1
3 2
Network Layer
4-4
Connection setup
 3rd important function in some network
architectures:

ATM, frame relay, X.25
 Before datagrams flow, two hosts and
intervening routers establish virtual
connection

Routers get involved
 Network and transport layer service:
 Network: between two hosts
 Transport: between two processes
Network Layer
4-5
Network service model
Q: What service model for “channel”
transporting packets from sender to
receiver?
 guaranteed bandwidth?
 preservation of inter-packet timing (no
jitter)?
 loss-free delivery?
 in-order delivery?
 congestion feedback to sender?
Network Layer
4-6
Chapter 4: Network Layer
 4. 1 Introduction
 4.2 Virtual circuit and
datagram networks
 4.3 What’s inside a
router
 4.4 IP: Internet
Protocol




Datagram format
IPv4 addressing
ICMP
IPv6
 4.5 Routing algorithms
 Link state
 Distance Vector
 Hierarchical routing
 4.6 Routing in the
Internet



RIP
OSPF
BGP
 4.7 Broadcast and
multicast routing
Network Layer
4-7
Forwarding table
Destination Address Range
4 billion
possible entries
Link Interface
11001000 00010111 00010000 00000000
through
11001000 00010111 00010111 11111111
0
11001000 00010111 00011000 00000000
through
11001000 00010111 00011000 11111111
1
11001000 00010111 00011001 00000000
through
11001000 00010111 00011111 11111111
2
otherwise
3
Network Layer
4-8
Longest prefix matching
Prefix Match
11001000 00010111 00010
11001000 00010111 00011000
11001000 00010111 00011
otherwise
Link Interface
0
1
2
3
Examples
DA: 11001000 00010111 00010110 10100001
Which interface?
DA: 11001000 00010111 00011000 10101010
Which interface?
DA: 11001000 00010111 10011000 10101010
Which interface?
Network Layer
4-9
Chapter 4: Network Layer
 4. 1 Introduction
 4.2 Virtual circuit and
datagram networks
 4.3 What’s inside a
router
 4.4 IP: Internet
Protocol




Datagram format
IPv4 addressing
ICMP
IPv6
 4.5 Routing algorithms
 Link state
 Distance Vector
 Hierarchical routing
 4.6 Routing in the
Internet



RIP
OSPF
BGP
 4.7 Broadcast and
multicast routing
Network Layer 4-10
Router Architecture Overview
Two key router functions:
 run routing algorithms/protocol (RIP, OSPF, BGP)
 forwarding datagrams from incoming to outgoing link
Network Layer
4-11
Input Port Functions
Physical layer:
bit-level reception
Data link layer:
e.g., Ethernet
see chapter 5
Decentralized switching:
 given datagram dest., lookup output port
using forwarding table in input port
memory
 goal: complete input port processing at
‘line speed’
 queuing: if datagrams arrive faster than
forwarding rate into switch fabric
Network Layer 4-12
Three types of switching fabrics
Network Layer 4-13
Switching Via Memory
First generation routers:
 traditional computers with switching under direct
control of CPU
packet copied to system’s memory
 speed limited by memory bandwidth (2 bus
crossings per datagram)
Input
Port
Memory
Output
Port
System Bus
Network Layer 4-14
Switching Via a Bus
 datagram from input port memory
to output port memory via a shared
bus
 bus contention: switching speed
limited by bus bandwidth

Only one packet can be on bus at any
time
 1 Gbps bus, Cisco 1900: sufficient
speed for access and enterprise
routers (not regional or backbone)
Network Layer 4-15
Switching Via An Interconnection
Network
 overcome bus bandwidth limitations
 Can pass multiple packets at the same time
 Cisco 12000: switches Gbps through the
interconnection network
Network Layer 4-16
Output Ports
 Buffering required when datagrams arrive from
fabric faster than the transmission rate
 Scheduling discipline chooses among queued
datagrams for transmission
Network Layer 4-17
Output port queueing
 buffering when arrival rate via switch exceeds
output line speed
 queueing (delay) and loss due to output port
buffer overflow!
Network Layer 4-18
Input Port Queuing
 Fabric slower than input ports combined -> queueing
may occur at input queues
 Head-of-the-Line (HOL) blocking: queued datagram
at front of queue prevents others in queue from
moving forward
 queueing delay and loss due to input buffer overflow!
Network Layer 4-19
Chapter 4: Network Layer
 4. 1 Introduction
 4.2 Virtual circuit and
datagram networks
 4.3 What’s inside a
router
 4.4 IP: Internet
Protocol




Datagram format
IPv4 addressing
ICMP
IPv6
 4.5 Routing algorithms
 Link state
 Distance Vector
 Hierarchical routing
 4.6 Routing in the
Internet



RIP
OSPF
BGP
 4.7 Broadcast and
multicast routing
Network Layer 4-20
Chapter 4: Network Layer
 4. 1 Introduction
 4.2 Virtual circuit and
datagram networks
 4.3 What’s inside a
router
 4.4 IP: Internet
Protocol




Datagram format
IPv4 addressing
ICMP
IPv6
 4.5 Routing algorithms
 Link state
 Distance Vector
 Hierarchical routing
 4.6 Routing in the
Internet



RIP
OSPF
BGP
 4.7 Broadcast and
multicast routing
Network Layer 4-21
IP datagram format
IP protocol version
Number (4)
header length (4)
(words)
“type” of data (not used)
max number
remaining hops
(decremented at
each router)
upper layer protocol
to deliver payload to
how much overhead
with TCP?
 20 bytes of TCP
 20 bytes of IP
 = 40 bytes + app
layer overhead
32 bits
head. type of
length
ver
len service
fragment
16-bit identifier flgs
offset
upper
time to
Header
layer
live
checksum
total datagram
length (bytes)
for
fragmentation/
reassembly
32 bit source IP address
32 bit destination IP address
Options (if any)
data
(variable length,
typically a TCP
or UDP segment)
E.g. timestamp,
record route
taken, specify
list of routers
to visit.
Network Layer 4-22
IP Fragmentation & Reassembly
 network links have MTU
(max.transfer size) - largest
possible link-level frame.
 different link types,
different MTUs
 large IP datagram divided
(“fragmented”) within net
 one datagram becomes
several datagrams
 “reassembled” only at final
destination
 IP header bits used to
identify, order related
fragments
fragmentation:
in: one large datagram
out: 3 smaller datagrams
reassembly
 Now most packet has less
than 1,500 bytes


due to Ethernet
Very rare fragmentation in
practice
Network Layer 4-23
Chapter 4: Network Layer
 4. 1 Introduction
 4.2 Virtual circuit and
datagram networks
 4.3 What’s inside a
router
 4.4 IP: Internet
Protocol




Datagram format
IPv4 addressing
ICMP
IPv6
 4.5 Routing algorithms
 Link state
 Distance Vector
 Hierarchical routing
 4.6 Routing in the
Internet



RIP
OSPF
BGP
 4.7 Broadcast and
multicast routing
Network Layer 4-24
IP Addressing: introduction
 IP address: 32-bit
identifier for host,
router interface
 interface: connection
between host/router
and physical link



router’s typically have
multiple interfaces
host typically has one
interface
IP addresses
associated with each
interface
223.1.1.1
223.1.2.1
223.1.1.2
223.1.1.4
223.1.1.3
223.1.2.9
223.1.3.27
223.1.2.2
223.1.3.2
223.1.3.1
223.1.1.1 = 11011111 00000001 00000001 00000001
223
1
1
1
Network Layer 4-25
Subnets
 IP address:
 subnet part (high
order bits)
 host part (low order
bits)
 What’s a subnet ?
 device interfaces with
same subnet part of IP
address
 can physically reach
each other without
intervening router
223.1.1.1
223.1.2.1
223.1.1.2
223.1.1.4
223.1.1.3
223.1.2.9
223.1.3.27
223.1.2.2
subnet
223.1.3.1
223.1.3.2
network consisting of 3 subnets
Network Layer 4-26
Subnets
Recipe
 To determine the
subnets, detach each
interface from its
host or router,
creating islands of
isolated networks.
Each isolated network
is called a subnet.
223.1.1.0/24
223.1.2.0/24
223.1.3.0/24
Subnet mask: /24
Network Layer 4-27
Subnets
223.1.1.2
How many?
223.1.1.1
223.1.1.4
223.1.1.3
223.1.9.2
223.1.7.0
223.1.9.1
223.1.7.1
223.1.8.1
223.1.8.0
223.1.2.6
223.1.2.1
223.1.3.27
223.1.2.2
223.1.3.1
223.1.3.2
Network Layer 4-28
IP addressing: CIDR
CIDR: Classless InterDomain Routing
subnet portion of address of arbitrary length
 address format: a.b.c.d/x, where x is # bits in
subnet portion of address

subnet
part
host
part
11001000 00010111 00010000 00000000
200.23.16.0/23
Network Layer 4-29
IP addresses: how to get one?
Q: How does host get IP address?
 hard-coded by system admin in a file
Wintel: control-panel->network->configuration>tcp/ip->properties
 UNIX: /etc/rc.config
 DHCP: Dynamic Host Configuration Protocol:
dynamically get address from a server in subnet
 “plug-and-play”
(more in next chapter)

Network Layer 4-30
IP addresses: how to get one?
Q: How does network get subnet part of IP
addr?
A: gets allocated portion of its provider ISP’s
address space
ISP's block
11001000 00010111 00010000 00000000
200.23.16.0/20
Organization 0
Organization 1
Organization 2
...
11001000 00010111 00010000 00000000
11001000 00010111 00010010 00000000
11001000 00010111 00010100 00000000
…..
….
200.23.16.0/23
200.23.18.0/23
200.23.20.0/23
….
Organization 7
11001000 00010111 00011110 00000000
200.23.30.0/23
Network Layer 4-31
Hierarchical addressing: route aggregation
Hierarchical addressing allows efficient advertisement of routing
information:
Organization 0
200.23.16.0/23
Organization 1
200.23.18.0/23
Organization 2
200.23.20.0/23
Organization 7
.
.
.
.
.
.
Fly-By-Night-ISP
“Send me anything
with addresses
beginning
200.23.16.0/20”
Internet
200.23.30.0/23
ISPs-R-Us
“Send me anything
with addresses
beginning
199.31.0.0/16”
Network Layer 4-32
Hierarchical addressing: more specific
routes
ISPs-R-Us has a more specific route to Organization 1
Organization 0
200.23.16.0/23
Organization 2
200.23.20.0/23
Organization 7
.
.
.
.
.
.
Fly-By-Night-ISP
“Send me anything
with addresses
beginning
200.23.16.0/20”
Internet
200.23.30.0/23
ISPs-R-Us
Organization 1
200.23.18.0/23
“Send me anything
with addresses
beginning 199.31.0.0/16
or 200.23.18.0/23”
Remember router’s longest matching principle
Network Layer 4-33
IP addressing: the last word...
Q: How does an ISP get block of addresses?
A: ICANN: Internet Corporation for Assigned
Names and Numbers
 allocates addresses
 manages DNS
 assigns domain names, resolves disputes
 ICANN publishes /8 address allocation
 You can use online “IP address locator” to find out
where a packet comes from


http://www.geobytes.com/IpLocator.htm
www.ip2location.com/free.asp
Network Layer 4-34
NAT: Network Address Translation
rest of
Internet
local network
(e.g., home network)
10.0.0/24
10.0.0.4
10.0.0.1
10.0.0.2
138.76.29.7
10.0.0.3
All datagrams leaving local
network have same single source
NAT IP address: 138.76.29.7,
different source port numbers
Datagrams with source or
destination in this network
have 10.0.0/24 address for
source, destination (as usual)
Network Layer 4-35
NAT: Network Address Translation
 Motivation: local network uses just one IP address as
far as outside world is concerned:
 no need to be allocated range of addresses from ISP:
- just one IP address is used for all devices
 devices inside local net not explicitly addressable,
visible by outside world (a security plus)
• Cannot be scanned or infected by worm or attackers outside
Internet
Network Layer 4-36
NAT: Network Address Translation
Implementation: NAT router must:



outgoing datagrams: replace (source IP address, port
#) of every outgoing datagram to (NAT IP address,
new port #)
. . . remote clients/servers will respond using (NAT
IP address, new port #) as destination addr.
remember (in NAT translation table) every (source
IP address, port #) to (NAT IP address, new port #)
translation pair
incoming datagrams: replace (NAT IP address, new
port #) in dest fields of every incoming datagram
with corresponding (source IP address, port #)
stored in NAT table
Network Layer 4-37
NAT: Network Address Translation
2: NAT router
changes datagram
source addr from
10.0.0.1, 3345 to
138.76.29.7, 5001,
updates table
2
NAT translation table
WAN side addr
LAN side addr
1: host 10.0.0.1
sends datagram to
128.119.40.186, 80
138.76.29.7, 5001 10.0.0.1, 3345
……
……
S: 10.0.0.1, 3345
D: 128.119.40.186, 80
S: 138.76.29.7, 5001
D: 128.119.40.186, 80
138.76.29.7
S: 128.119.40.186, 80
D: 138.76.29.7, 5001
3: Reply arrives
dest. address:
138.76.29.7, 5001
3
1
10.0.0.4
S: 128.119.40.186, 80
D: 10.0.0.1, 3345
10.0.0.1
10.0.0.2
4
10.0.0.3
4: NAT router
changes datagram
dest addr from
138.76.29.7, 5001 to 10.0.0.1, 3345
Network Layer 4-38
NAT: Network Address Translation
 16-bit port-number field:

60,000 simultaneous connections with a single
LAN-side address!
 NAT is controversial:
 violates
end-to-end argument
• Internal computers not visible to outside
• Outside hosts have trouble to request service from
local computers, e.g., P2P, video conference, web
hosting.

address shortage should instead be solved by
IPv6
Network Layer 4-39