3rd Edition: Chapter 4

Download Report

Transcript 3rd Edition: Chapter 4

Announcement
 Project #2 due midnight
 Homework #3 due Friday midnight
 Project #3 is out
1
Last class

Distance vector
 IP: Internet Protocol
 Datagram format
 IPv4 addressing
 NAT
2
Dx(y) = min{c(x,y) + Dy(y), c(x,z) + Dz(y)}
= min{2+0 , 7+1} = 2
node x table
cost to
x y z
x ∞∞ ∞
y ∞∞ ∞
z 71 0
from
from
from
from
x 0 2 7
y 2 0 1
z 7 1 0
cost to
x y z
x 0 2 7
y 2 0 1
z 3 1 0
x 0 2 3
y 2 0 1
z 3 1 0
cost to
x y z
x 0 2 3
y 2 0 1
z 3 1 0
x
2
y
7
1
z
cost to
x y z
from
from
from
x ∞ ∞ ∞
y 2 0 1
z ∞∞ ∞
node z table
cost to
x y z
x 0 2 3
y 2 0 1
z 7 1 0
cost to
x y z
cost to
x y z
from
from
x 0 2 7
y ∞∞ ∞
z ∞∞ ∞
node y table
cost to
x y z
cost to
x y z
Dx(z) = min{c(x,y) +
Dy(z), c(x,z) + Dz(z)}
= min{2+1 , 7+0} = 3
x 0 2 3
y 2 0 1
z 3 1 0
time
3
The Internet Network layer
Host, router network layer functions:
Transport layer: TCP, UDP
Network
layer
IP protocol
•addressing conventions
•datagram format
•packet handling conventions
Routing protocols
•path selection
•RIP, OSPF, BGP
forwarding
table
ICMP protocol
•error reporting
•router “signaling”
Link layer
physical layer
4
IP datagram format
IP protocol version
number
header length
(bytes)
“type” of data
max number
remaining hops
(decremented at
each router)
upper layer protocol
to deliver payload to
how much overhead
with TCP?
 20 bytes of TCP
 20 bytes of IP
 = 40 bytes + app
layer overhead
32 bits
head. type of
length
ver
len service
fragment
16-bit identifier flgs
offset
upper
time to
Internet
layer
live
checksum
total datagram
length (bytes)
for
fragmentation/
reassembly
32 bit source IP address
32 bit destination IP address
Options (if any)
data
(variable length,
typically a TCP
or UDP segment)
E.g. timestamp,
record route
taken, specify
list of routers
to visit.
5
IP addressing: CIDR
Before CIDR: only 8-, 16-, and 24- bit masks were
available (A, B, and C class networks)
CIDR: Classless InterDomain Routing
subnet portion of address of arbitrary length
 address format: a.b.c.d/x, where x is # bits in
subnet portion of address

subnet
part
host
part
11001000 00010111 00010000 00000000
200.23.16.0/23
6
Overview
ICMP
 IPv6

 Routing in the Internet
 Hierarchical routing
 RIP
 OSPF
 BGP
7
ICMP: Internet Control Message Protocol
 used by hosts & routers to
communicate network-level
information
 error reporting:
unreachable host, network,
port, protocol
 echo request/reply (used
by ping)
 network-layer “above” IP:
 ICMP msgs carried in IP
datagrams
 ICMP message: type, code plus
first 8 bytes of IP datagram
causing error
Type
0
3
3
3
3
3
3
4
Code
0
0
1
2
3
6
7
0
8
9
10
11
12
0
0
0
0
0
description
echo reply (ping)
dest. network unreachable
dest host unreachable
dest protocol unreachable
dest port unreachable
dest network unknown
dest host unknown
source quench (congestion
control - not used)
echo request (ping)
route advertisement
router discovery
TTL expired
bad IP header
8
Traceroute and ICMP
 Source sends series of
UDP segments to dest



First has TTL =1
Second has TTL=2, etc.
Unlikely port number
 When nth datagram arrives
to nth router:



Router discards datagram
And sends to source an
ICMP message (type 11,
code 0)
Message includes name of
router& IP address
 When ICMP message
arrives, source calculates
RTT
 Traceroute does this 3
times
Stopping criterion
 UDP segment eventually
arrives at destination host
 Destination returns ICMP
“host unreachable” packet
(type 3, code 3)
 When source gets this
ICMP, stops.
9
Overview
ICMP
 IPv6

 Routing in the Internet
 Hierarchical routing
 RIP
 OSPF
 BGP
10
IPv6
 Initial motivation: 32-bit address space soon
to be completely allocated.
 Additional motivation:
header format helps speed processing/forwarding
 header changes to facilitate QoS
IPv6 datagram format:
 fixed-length 40 byte header
 no fragmentation allowed

11
IPv6 Header (Cont)
Priority: identify priority among datagrams in flow
Flow Label: identify datagrams in same “flow.”
(concept of“flow” not well defined).
Next header: identify upper layer protocol for data
12
Other Changes from IPv4
 Checksum: removed entirely to reduce
processing time at each hop
 Options: allowed, but outside of header,
indicated by “Next Header” field
 ICMPv6: new version of ICMP
additional message types, e.g. “Packet Too Big”
 multicast group management functions

13
Transition From IPv4 To IPv6
 Not all routers can be upgraded simultaneous
no “flag days”
 How will the network operate with mixed IPv4 and
IPv6 routers?

 Tunneling: IPv6 carried as payload in IPv4
datagram among IPv4 routers
14
Tunneling
Logical view:
Physical view:
A
B
IPv6
IPv6
A
B
C
IPv6
IPv6
IPv4
Flow: X
Src: A
Dest: F
data
A-to-B:
IPv6
E
F
IPv6
IPv6
D
E
F
IPv4
IPv6
IPv6
tunnel
Src:B
Dest: E
Src:B
Dest: E
Flow: X
Src: A
Dest: F
Flow: X
Src: A
Dest: F
data
data
B-to-C:
IPv6 inside
IPv4
B-to-C:
IPv6 inside
IPv4
Flow: X
Src: A
Dest: F
data
E-to-F:
IPv6
15
Overview
ICMP
 IPv6

 Routing in the Internet
 Hierarchical routing
 RIP
 OSPF
 BGP
16
Hierarchical Routing
Our routing study thus far - idealization
 all routers identical
 network “flat”
… not true in practice
scale: with 200 million
destinations:
 can’t store all dest’s in
routing tables!
 routing table exchange
would swamp links!
administrative autonomy
 internet = network of
networks
 each network admin may
want to control routing in its
own network
17
Hierarchical Routing
 aggregate routers into
regions, “autonomous
systems” (AS)
 routers in same AS run
same routing protocol


Gateway router
 Direct link to router in
another AS
“intra-AS” routing
protocol
routers in different AS
can run different intraAS routing protocol
18
Interconnected ASes
3c
3a
3b
AS3
1a
2a
1c
1d
1b
Intra-AS
Routing
algorithm
2c
AS2
AS1
Inter-AS
Routing
algorithm
Forwarding
table
2b
 Forwarding table is
configured by both
intra- and inter-AS
routing algorithm


Intra-AS sets entries
for internal dests
Inter-AS & Intra-As
sets entries for
external dests
19
Inter-AS tasks
AS1 needs:
1. to learn which dests
are reachable through
AS2 and which
through AS3
2. to propagate this
reachability info to all
routers in AS1
Job of inter-AS routing!
 Suppose router in AS1
receives datagram for
which dest is outside
of AS1

Router should forward
packet towards one of
the gateway routers,
but which one?
3c
3b
3a
AS3
1a
2a
1c
1d
1b
2c
AS2
2b
AS1
20
Example: Setting forwarding table
in router 1d
 Suppose AS1 learns from the inter-AS
protocol that subnet x is reachable from
AS3 (gateway 1c) but not from AS2.
 Inter-AS protocol propagates reachability
info to all internal routers.
 Router 1d determines from intra-AS
routing info that its interface I is on the
least cost path to 1c.
 Puts in forwarding table entry (x,I).
21
Example: Choosing among multiple ASes
 Now suppose AS1 learns from the inter-AS protocol
that subnet x is reachable from AS3 and from AS2.
 To configure forwarding table, router 1d must
determine towards which gateway it should forward
packets for dest x.
 This is also the job on inter-AS routing protocol!
 Hot potato routing: send packet towards closest of
two routers.
Learn from inter-AS
protocol that subnet
x is reachable via
multiple gateways
Use routing info
from intra-AS
protocol to determine
costs of least-cost
paths to each
of the gateways
Hot potato routing:
Choose the gateway
that has the
smallest least cost
Determine from
forwarding table the
interface I that leads
to least-cost gateway.
Enter (x,I) in
forwarding table
22
Intra-AS Routing
 Also known as Interior Gateway Protocols (IGP)
 Most common Intra-AS routing protocols:

RIP: Routing Information Protocol

OSPF: Open Shortest Path First

IGRP: Interior Gateway Routing Protocol (Cisco
proprietary)
23
Overview
ICMP
 IPv6

 Routing in the Internet
 Hierarchical routing
 RIP
 OSPF
 BGP
24
RIP ( Routing Information Protocol)
 Distance vector algorithm
 Included in BSD-UNIX Distribution in 1982
 Distance metric: # of hops (max = 15 hops)
 # of hops: # of subnets traversed along the shortest path
from src. router to dst. subnet (e.g., src. = A)
u
v
A
z
C
B
D
w
x
y
destination hops
u
1
v
2
w
2
x
3
y
3
z
2
25
RIP advertisements
 Distance vectors: exchanged among
neighbors every 30 sec via Response
Message (also called advertisement)
 Each advertisement: list of up to 25
destination nets within AS
26
RIP: Example
z
w
A
x
D
B
y
C
Destination Network
w
y
z
x
….
Next Router
Num. of hops to dest.
….
....
A
B
B
--
2
2
7
1
Routing table in D
27
RIP: Example
Dest
w
x
z
….
Next
C
…
w
hops
4
...
A
Advertisement
from A to D
z
x
Destination Network
w
y
z
x
….
D
B
C
y
Next Router
Num. of hops to dest.
….
....
A
B
B A
--
Routing table in D
2
2
7 5
1
28
RIP: Link Failure and Recovery
If no advertisement heard after 180 sec -->
neighbor/link declared dead
 routes via neighbor invalidated
 new advertisements sent to neighbors
 neighbors in turn send out new advertisements (if
tables changed)
 link failure info quickly propagates to entire net
 poison reverse used to prevent ping-pong loops
(infinite distance = 16 hops)
29
RIP Table processing
 RIP routing tables managed by application-level
process called route-d (daemon)
 advertisements sent in UDP packets, periodically
repeated
 RIP implemented as an app-layer protocol running
over UDP
routed
routed
Transprt
(UDP)
network
(IP)
link
physical
Transprt
(UDP)
forwarding
table
forwarding
table
network
(IP)
link
physical
30
Overview
ICMP
 IPv6

 Routing in the Internet
 Hierarchical routing
 RIP
 OSPF
 BGP
31
OSPF (Open Shortest Path First)
 “open”: publicly available
 Uses Link State algorithm
 LS packet dissemination
 Topology map at each node
 Route computation using Dijkstra’s algorithm
 Link costs configured by the network administrator
 OSPF advertisement carries one entry per neighbor
router
 Advertisements disseminated to entire AS (via
flooding)

Carried in OSPF messages directly over IP (rather than TCP
or UDP
32
OSPF “advanced” features (not in RIP)
 Security: all OSPF messages authenticated (to




prevent malicious intrusion)
Multiple same-cost paths allowed (only one path in
RIP)
For each link, multiple cost metrics for different
TOS (e.g., satellite link cost set “low” for best effort;
high for real time)
Integrated uni- and multicast support:
 Multicast OSPF (MOSPF) uses same topology data
base as OSPF
Hierarchical OSPF in large domains.
33
Hierarchical OSPF
34
Hierarchical OSPF
 Two-level hierarchy: local area, backbone.
 Link-state
advertisements only in area
 each node has detailed area topology;
 Area border routers: “summarize” distances
to nets in own area, advertise to other Area
Border routers.
 Backbone routers: run OSPF routing limited
to backbone.
 Boundary routers: connect to other AS’s.
35
Overview
ICMP
 IPv6

 Routing in the Internet
 Hierarchical routing
 RIP
 OSPF
 BGP
36
Internet inter-AS routing: BGP
 BGP (Border Gateway Protocol): the de
facto standard
 BGP provides each AS a means to:
1.
2.
3.
Obtain subnet reachability information from
neighboring ASs.
Propagate the reachability information to all
routers internal to the AS.
Determine “good” routes to subnets based on
reachability information and policy.
 Allows a subnet to advertise its existence
to rest of the Internet: “I am here”
37
BGP basics
 Pairs of routers (BGP peers) exchange routing info over TCP
conections: BGP sessions
 Note that BGP sessions do not correspond to physical links.
 When AS2 advertises a prefix to AS1, AS2 is promising it will
forward any datagrams destined to that prefix towards the
prefix.

AS2 can aggregate prefixes in its advertisement
3c
3a
3b
AS3
1a
AS1
2a
1c
1d
1b
2c
AS2
2b
eBGP session
iBGP session
38
Distributing reachability info
 With eBGP session between 3a and 1c, AS3 sends prefix
reachability info to AS1.
 1c can then use iBGP do distribute this new prefix reach info
to all routers in AS1
 1b can then re-advertise the new reach info to AS2 over the
1b-to-2a eBGP session
 When router learns about a new prefix, it creates an entry
for the prefix in its forwarding table.
3c
3a
3b
AS3
1a
AS1
2a
1c
1d
1b
2c
AS2
2b
eBGP session
iBGP session
39
Path attributes & BGP routes
 When advertising a prefix, advert includes BGP
attributes.

prefix + attributes = “route”
 Two important attributes:
 AS-PATH: contains the ASs through which the advert
for the prefix passed: AS 67 AS 17
 NEXT-HOP: Indicates the specific internal-AS router to
next-hop AS. (There may be multiple links from current
AS to next-hop-AS.)
 When gateway router receives route advert, uses
import policy to accept/decline.
40