Transcript Network Debugging - Andrew.cmu.edu

Network Debugging
Organizational Communications
and Technologies
Prithvi Rao
H. John Heinz III School of Public
Policy and Management
Carnegie Mellon University
Objectives

Present some examples of debugging tools
Readings
Suggested reading: Class notes
Practical Internetworking with TCP/IP
and UNIX (not required)
Tools for Debugging

Most tools are available for Unix based systems (most
servers are likely to be UNIX)

Some tools are freely available (traceroute and dig)

Some proprietary tools exist (etherfind)
Ping

Simple yet valuable network debugging tool






Sends an ICMP echo request message to remote host
Remote host sends back an ICMP echo and reply message
Sending an echo is called “pinging”
Good baseline test of connectivity
Successful ping implies that IP packets can be exchanged
Network routing is also tested with ping
Example
% ping unix5.andrew.cmu.edu
unix5.andrew.cmu.edu is alive
Ping

Variant of first form of ping
Example
% ping -s akasha.tic.com 5
no response from akasha.tic.com
64 bytes from akasha.tic.com (192.12.23.130) icmp_seq = 0, time = 6 ms
64 bytes from akasha.tic.com (192.12.23.130) icmp_seq = 1, time = 5 ms
64 bytes from akasha.tic.com (192.12.23.130) icmp_seq =2, time = 5 ms
In this case command times out after 5 seconds
Ping




Echo request and echo reply are part of ICMP
Ping does not rely on application server running on
remote host
Relies on network interface card to be configured
properly
Unix host in single-user-mode will respond to ping
commands
Remote Script


Script that permits running of arbitrary command on
remote machine
Uses the remote shell (rsh) protocol
Example
% remote uptime –h unix5.andrew.cmu.edu
Host: unix5.andrew.cmu.edu
8:30 am up 5 days <time> <#users> <load average>
Netstat

Netstat is jack-of-all-trades network tool





Can display connections, interfaces, routing tables and traffic
statistics
Active connection display
Statistics display
Interfaces
Routing
Routing: netstat -r

Displays kernel routing table
Example
% netstat –r
Destination
Gateway
127.0.0.1
127.0.01
default
192.12.23.132
192.12.23.128 192.12.23.129
Flags
Refcnt
Use
UH
UG
U
12
0
16
244870
51
8248341
Interface
le0
le0
le0
Routing: netstat -r





Gateway is the IP address of the next hop to which
to send address
Flags is the status of each route
Refcnt is the current number of active TCP
connections
Use is the total number of IP packets sent using
route
Interface is the logical name of the local interface
Routing: netstat -i

Can display status of all interfaces
Example
% netstat –i –n
Name MTU Net/Dest
le0
Address
Ipkts
Ierrs Opkts Oerrs Coll
1500 192.12.23.128 192.12.23.129 8141411 0
7902647
0
61
Routing: netstat -i









Name is logical name of network
MTU is size in bytes of MTU interface
Net/Dest IP address of network to which interface is connected
or that of end-point of link
Address is local IP address of interface
Ipkts is count of datalink frames received on link since last
bootstrap
Ierrs is number of datalink frames received with errors and
dropped by interface
Opkts is datalink frames sent on interface since last boot
Oerrs count of frames not sent due to output errors
Coll is count of collisions detected by this interface
Routing: netstat -f

Permits looking at TCP and UDP packets only
Example
% netstat –f inet
Active internet connections
Proto
Rec-Q Req-Q Local Address Foreign Address (state)
tcp
0
4096 kiwilabs.com
kia.smtp ESTABLISHED
Routing: netstat -f






Proto is the protocol (TCP or UDP)
Recv-Q number of bytes in socket input queue
Send-Q number of bytes in socket output queue
Local address set of period separated names
Foreign address is remote socket address given in
format of local address
(state) is current state of TCP connection. Field is
always empty for UDP connections
Traceroute

Traces route an IP packet takes to destination host



Takes single hostname argument and lists all intermediate router
Sends three UDP messages encapsulated in an IP packet and
records the round-trip time in milliseconds for each message sent
to intermediate router
Lost message or router that does not respond is denoted with a “*”
Example
% traceroute unix5.andrew.cmu.edu
ARP: Address Resolution
Protocol

Arp command permits the examining and modifying
of local ARP cache
Example
% arp -a
Etherfind

Specific to Sun for tracing Ethernet frames




Performs functions of a network analyzer
Output can be piped to other unix tools (grep, awk, sed)
Can display selective frames
Mainly useful for TCP/IIP
Example
% etherfind –i le0 –v –t greater 0
nslookup

Simple tool for querying DNS servers

Without arguments user is prompted for queries
Example
% nslookup <unix5>
> unix5
> ls kiwilabs.com
> set type = pttr
> set type = any
Summary

Presented examples of network debugging tools

Discussed the use of these tools for various purposes