Transcript ppt

15-441 Computer Networking
Lecture 6
Data link Layer – Access Control
Based on slides by Peter Steenkiste
Copyright ©, Carnegie Mellon 2007-10
1
Datalink Functions

Framing: encapsulating a network layer
datagram into a bit stream.
» Add header, mark and detect frame boundaries, …

Error control: error detection and correction
to deal with bit errors.
» May also include other reliability support, e.g.
retransmission


Flow control: avoid sender overrunning
receiver.
Media access: controlling which frame should
be sent over the link next.
» Easy for point-to-point links
» Harder for multi-access links: who gets to send?
2
So far …
Can connect two nodes
• … But what if we want more nodes?
Wires for everybody!
3
So far …
Can connect two nodes
• … But what if we want more nodes?
Wires for everybody!
P-2-p
shared
switches
4
Datalink Architectures

Point-Point with switches

Media access
control.
5
Media Access Control


How do we transfer packets between two
hosts connected to the same network?
Switches connected by point-to-point links -store-and-forward.
» Used in WAN, LAN, and for home connections
» Conceptually similar to “routing”
– But at the datalink layer instead of the network layer

Multiple access networks -- contention based.
» Multiple hosts are sharing the same transmission
medium
» Used in LANs and wireless
» Need to control access to the medium
6
Datalink Classification
Datalink
Switch-based
Virtual
Circuits
Packet
Switching
ATM,
framerelay
Bridged
LANs
Multiple Access
Scheduled
Access
Random
Access
Token ring,
Ethernet,
FDDI, 802.11 802.11, Aloha
7
Switching




Forward units of data based on address in header.
Many data-link technologies use switching.
» Virtual circuits: Frame Relay, ATM, X.25, ..
» Packets: Ethernet, MPLS, …
“Switching” also happens at the network layer.
» Layer 3: Internet protocol
» In this case, address is an IP address
» IP over SONET, IP over ATM, ...
» Otherwise, operation is very similar
Switching is different from SONET mux/demux.
» SONET channels statically configured - no addresses
8
A Switch-based Network


Switches are connected by point-point links.
Packets are forwarded hop-by-hop by the
switches towards the destination.
» Forwarding is based on the address



How does a switch work?
How do nodes exchange packets over a link?
How is the destination addressed?
Switch
PCs at
Work
Point-Point
link
PC at
Home
9
Switch Architecture

Packets come in one
interface, forwarded to output
interface based on address.
» Same idea for bridges, switches,
routers: address look up differs

Control processor manages
the switch and executes
higher level protocols.
» E.g. routing, management, ...


The switch fabric directs the
traffic to the right output port.
The input and output ports
deal with transmission and
reception of packets.
Control
Processor
Input
Port
Output
Port
Output
Port
Input
Port
Switch
Fabric
Output
Port
Input
Port
Output
Port
Input
Port
10
Connections or Not?

Two basic approaches to packet forwarding
»Connectionless
»(virtual) Circuit switched

When would you use?
11
Connectionless

Host can send anytime anywhere

No idea if resources are available to get to dest

Forwarding is independent for each packet

No setup time

Fault tolerant
Destination
Port
A
3
B
0
C
D
E
12
Virtual Circuit Switching

Two stage process
»Setup connection (create VCIs)
»Send packets

RTT introduced before any data is sent

Per packet overhead can be smaller (VCI << adr)

Switch failures are hard to deal with

Reserves resources for connection
13
Setup, assign VCIs
14
Packet Forwarding:
Address Lookup
Switch
Address Next Hop
B31123812508
38913C3C2137
A21023C90590
3
3
0
Info
13
-

» Absolute address (e.g. Ethernet)
» (IP address for routers)
» (VC identifier, e.g. ATM))


128.2.15.3 1
(2,34)
Address from header.

Next hop: output port for packet.
Info: priority, VC id, ..
Table is filled in by protocol.
15
Datalink Classification
Datalink
Switch-based
Virtual
Circuits
Packet
Switching
ATM,
framerelay
Bridged
LANs
Multiple Access
Scheduled
Access
Random
Access
Token ring,
Ethernet,
FDDI, 802.11 802.11, Aloha
16
Problem: Sharing a Wire
Learned how to connect hosts

… But what if we want more hosts?

Wires for everybody!
Switches
Expensive! How can we share a wire?
17
Listen and Talk
yak yak…

Natural scheme – listen before you talk…
»Works well in practice
18
18
Listen and Talk
yada yada…

Natural scheme – listen before you talk…
»Works well in practice
19
19
Listen and Talk
yada
yak yak…
yada…

Natural scheme – listen before you talk…
»Works well in practice

But sometimes this breaks down
»Why? How do we fix/prevent this?
20
20
Problem: Who is this packet for?

Need to put an address on the packet

What should it look like?

How do you determine your own address?

How do you know what address you want to send it
to?
21
21
Outline

Aloha

Ethernet MAC

Collisions

Ethernet Frames
22
22
Random Access Protocols

When node has packet to send
» Transmit at full channel data rate R
» No a priori coordination among nodes
Two or more transmitting nodes  “collision”
 Random access MAC protocol specifies:

» How to detect collisions
» How to recover from collisions (e.g., via delayed
retransmissions)

Examples of random access MAC protocols:
» Slotted ALOHA and ALOHA
» CSMA and CSMA/CD
23
23
Aloha – Basic Technique

First random MAC developed
» For radio-based communication in Hawaii (1970)

Basic idea:
» When you are ready, transmit
» Receivers send ACK for data
» Detect collisions by timing out for ACK
» Recover from collision by trying after random
delay
– Too short  large number of collisions
– Too long  underutilization
24
24
Slotted Aloha

Time is divided into equal size slots
» Equal to packet transmission time

Node (w/ packet) transmits at beginning of next slot

If collision: retransmit pkt in future slots with
probability p, until successful
Success (S), Collision (C), Empty (E) slots
25
25
Pure (Unslotted) ALOHA

Unslotted Aloha: simpler, no synchronization

Pkt needs transmission:
» Send without awaiting for beginning of slot

Collision probability increases:
» Pkt sent at t0 collide with other pkts sent in [t0-1, t0+1]
26
26
Outline

Aloha

Ethernet MAC

Collisions

Ethernet Frames
27
27
Ethernet
First practical local area network, built at
Xerox PARC in 70’s
 “Dominant” LAN technology:

» Cheap
» Kept up with speed race: 10, 100, 1000 Mbps
Metcalfe’s Ethernet
sketch
28
28
Ethernet MAC – Carrier Sense

Basic idea:
» Listen to wire before
transmission
» Avoid collision with
active transmission

Why didn’t ALOHA
have this?
» In wireless, relevant
contention at the
receiver, not sender
Hidden
Exposed
St.Louis
NY
Chicago
CMU
CMU
Chicago
NY
– Hidden terminal
– Exposed terminal
29
29
Ethernet MAC – Collision
Detection

But: ALOHA has collision detection also?
» That was very slow and inefficient

Basic idea:
» Listen while transmitting
» If you notice interference  assume collision

Why didn’t ALOHA have this?
» Very difficult for radios to listen and transmit
» Signal strength is reduced by distance for radio
– Much easier to hear “local, powerful” radio station
than one in NY
– You may not notice any “interference”
30
30
Ethernet MAC (CSMA/CD)

Carrier Sense Multiple Access/Collision
Detection
Packet?
No
Sense
Carrier
Send
Detect
Collision
Yes
Discard
Packet
attempts < 16
Jam channel
b=CalcBackoff();
wait(b);
attempts++;
attempts == 16
31
31
Ethernet CSMA/CD:
Making it word
Jam Signal: make sure all other transmitters
are aware of collision; 48 bits;
Exponential Backoff:
 If deterministic delay after collision,
collision will occur again in lockstep
 Why not random delay with fixed mean?
» Few senders  needless waiting
» Too many senders  too many collisions

Goal: adapt retransmission attempts to
estimated current load
» heavy load: random wait will be longer
32
32
Ethernet Backoff Calculation

Exponentially increasing random delay
»Infer senders from # of collisions
»More senders  increase wait time



First collision: choose K from {0,1}; delay is K
x 512 bit transmission times
After second collision: choose K from
{0,1,2,3}…
After ten or more collisions, choose K from
{0,1,2,3,4,…,1023}
33
33
Outline

Aloha

Ethernet MAC

Collisions

Ethernet Frames
34
34
Collisions
B
C
Time
A
35
35
Minimum Packet Size

What if two people
sent really small
packets
» How do you find
collision?
36
36
Ethernet Collision Detect

Min packet length > 2x max prop delay
»If A, B are at opposite sides of link,
and B starts one link prop delay after
A

Jam network for 32-48 bits after collision,
then stop sending
»Ensures that everyone notices
collision
37
37
End to End Delay

c in cable = 60% * c in vacuum = 1.8 x 10^8
m/s

Modern 10Mb Ethernet
» 2.5km, 10Mbps
» ~= 12.5us delay
» +Introduced repeaters (max 5 segments)
» Worst case – 51.2us round trip time!

Slot time = 51.2us = 512bits in flight
» After this amount, sender is guaranteed sole
access to link
» 51.2us = slot time for backoff
38
38
Packet Size

What about scaling? 3Mbit, 100Mbit,
1Gbit...
» Original 3Mbit Ethernet did not have minimum
packet size
– Max length = 1Km and No repeaters
» For higher speeds must make network smaller,
minimum packet size larger or both

What about a maximum packet size?
» Needed to prevent node from hogging the
network
» 1500 bytes in Ethernet
39
39
10BaseT and 100BaseT

10/100 Mbps rate; latter called “fast ethernet”

T stands for Twisted Pair (wiring)

Minimum packet size requirement
» Make network smaller  solution for 100BaseT
40
40
Gbit Ethernet

Minimum packet size requirement
» Make network smaller?
– 512bits @ 1Gbps = 512ns
– 512ns * 1.8 * 10^8 = 92meters = too small !!
» Make min pkt size larger!
– Gigabit Ethernet uses collision extension for small pkts
and backward compatibility

Maximum packet size requirement
» 1500 bytes is not really “hogging” the network
» Defines “jumbo frames” (9000 bytes) for higher
efficiency
41
41
Outline

Aloha

Ethernet MAC

Collisions

Ethernet Frames
42
42
Ethernet Frame Structure

Sending adapter encapsulates IP datagram (or other
network layer protocol packet) in Ethernet frame
43
43
Ethernet Frame Structure (cont.)

Preamble: 8 bytes
»101010…1011
»Used to synchronize receiver,
sender clock rates

CRC: 4 bytes
»Checked at receiver, if error is
detected, the frame is simply
dropped
44
44
Ethernet Frame Structure (cont.)

Each protocol layer needs to provide
some hooks to upper layer protocols
» Demultiplexing: identify which upper layer
protocol packet belongs to
» E.g., port numbers allow TCP/UDP to identify
target application
» Ethernet uses Type field

Type: 2 bytes
» Indicates the higher layer protocol, mostly IP
but others may be supported such as Novell
IPX and AppleTalk)
45
45
Addressing Alternatives

Broadcast  all nodes receive all packets
» Addressing determines which packets are kept and
which are packets are thrown away
» Packets can be sent to:
– Unicast – one destination
– Multicast – group of nodes (e.g. “everyone playing Quake”)
– Broadcast – everybody on wire

Dynamic addresses (e.g. Appletalk)
» Pick an address at random
» Broadcast “is anyone using address XX?”
» If yes, repeat

Static address (e.g. Ethernet)
46
46
Ethernet Frame Structure (cont.)

Addresses: 6 bytes
» Each adapter is given a globally unique
address at manufacturing time
– Address space is allocated to manufacturers

24 bits identify manufacturer

E.g., 0:0:15:*  3com adapter
– Frame is received by all adapters on a LAN and
dropped if address does not match
» Special addresses
– Broadcast – FF:FF:FF:FF:FF:FF is “everybody”
– Range of addresses allocated to multicast

Adapter maintains list of multicast groups node is
interested in
47
47
Why Did Ethernet Win?

Failure modes
» Token rings – network unusable
» Ethernet – node detached

Good performance in common case
» Deals well with bursty traffic
» Usually used at low load

Volume  lower cost  higher volume ….

Adaptable
» To higher bandwidths (vs. FDDI)
» To switching (vs. ATM)

Easy incremental deployment

Cheap cabling, etc
48
48
And .. It is Easy to Manage

You plug in the host and it basically works
» No configuration at the datalink layer
» Today: may need to deal with security
Protocol is fully distributed
 Broadcast-based.

» In part explains the easy management
» Some of the LAN protocols (e.g. ARP) rely on
broadcast
– Networking would be harder without ARP
» Not having natural broadcast capabilities adds
complexity to a LAN
– Example: ATM
49
49
Ethernet Problems:
Unstable at High Load

Peak throughput worst with
» More hosts – more collisions to identify single
sender
» Smaller packet sizes – more frequent arbitration
» Longer links – collisions take longer to observe,
more wasted bandwidth
1/e = 37%
 But works well
in practice
0.4
» Can improve
efficiency by
avoiding
above
conditions
0.3
Slotted Aloha
0.2
0.1
Pure Aloha
0.5
1.0
1.5
2.0
G = offered load = N X p
50
Summary

CSMA/CD  carrier sense multiple access
with collision detection
» Why do we need exponential backoff?
» Why does collision happen?
» Why do we need a minimum packet size?
– How does this scale with speed?

Ethernet
» What is the purpose of different header fields?
» What do Ethernet addresses look like?

What are some alternatives to Ethernet
design?
52
52
Datalink Layer Architectures


Packet forwarding.
Error and flow control.


Media access
control.
Scalability.
60
Datalink Classification
Datalink
Switch-based
Virtual
Circuits
Packet
Switching
ATM,
framerelay
Bridged
LANs
Multiple Access
Scheduled
Access
Random
Access
Token ring,
Ethernet,
FDDI, 802.11 802.11, Aloha
61
61
Multiple Access Protocols

Prevent two or more nodes from transmitting
at the same time over a broadcast channel.
» If they do, we have a collision, and receivers will not be
able to interpret the signal

Several classes of multiple access protocols.
» Partitioning the channel, e.g. frequency-division or time
division multiplexing
– With fixed partitioning of bandwidth –
– Not flexible; inefficient for bursty traffic
» Taking turns, e.g. token-based, reservation-based
protocols, polling based
» Contention based protocols, e.g. Aloha, Ethernet
– Next lecture
62
Fiber Distributed Data Interface
(FDDI)

One token holder may send,
with a time limit
» Provides known upper bound on
delay.




Optical version of 802.5 token
ring, but multiple packets may
travel in train: token released
at end of frame
100 Mbps, 100km
Optional dual ring for fault
tolerance
Concerns:
» Token overhead
» Latency
» Single point of failure
63
Other “Taking Turn”
Protocols

Central entity polls stations, inviting them to
transmit
» Simple design – no conflicts
» Not very efficient – overhead of polling operation
» Example: the “Point Control Function” mode for 802.11

Stations reserve a slot for transmission.
» For example, break up the transmission time in
contention-based and reservation based slots
– Contention based slots can be used for short
messages or to reserve time slots
– Communication in reservation based slots only
allowed after a reservation is made
» Issues: fairness, efficiency
64
MAC Protocols - Discussion



Channel partitioning MAC protocols:
» Share channel efficiently at high load
» Inefficient at low load: delay in channel
access, 1/N bandwidth allocated even if
only 1 active node!
“Taking turns” protocols
» More flexible bandwidth allocation, but
» Protocol can introduce unnecessary
overhead and access delay at low load
Random access MAC protocols (next lecture)
» Efficient at low load: single node can fully
utilize channel
» High load: collision overhead
Copyright (C), CMU
65
65