Transcript Circuit Switching, Packet Switching, The Network Layer

Data Communication and
Networks
Lecture 6
Networks: Part 1
Circuit Switching, Packet Switching, The Network Layer
October 13, 2005
Network Layer
4-1
Switching Networks
 Long distance transmission is typically done
over a network of switched nodes
 Nodes not concerned with content of data
 End devices are stations

Computer, terminal, phone, etc.
 A collection of nodes and connections is a
communications network
 Data routed by being switched from node
to node
Network Layer
4-2
Technology
 Two different switching technologies
Circuit switching
 Packet switching

Network Layer
4-3
Simple Switched Network
Network Layer
4-4
Circuit Switching
 Dedicated communication path between
two stations (during conversation)
 Three phases
Establish
 Transfer
 Disconnect

 Must have switching capacity and channel
capacity to establish connection
 Must have intelligence to work out routing
Network Layer
4-5
Circuit Switching - Issues
 Circuit switching is inefficient (designed
for voice)
Resources dedicated to a particular call
 Much of the time a data connection is idle
 Data rate is fixed

• Both ends must operate at the same rate
 Set up (connection) takes time
 Once connected, transfer is transparent
Network Layer
4-6
Packet Switching
Network Layer
4-7
Basic Operation
 Data transmitted in small packets
Typically 1000 octets
 Longer messages split into series of packets
 Each packet contains a portion of user data plus
some control info

 Control info
 Routing (addressing) info
 Packets are received, stored briefly
(buffered) and passed on to the next node

Store and forward
Network Layer
4-8
Use of Packets
Network Layer
4-9
Network layer
 transport segment from




sending to receiving host
on sending side
encapsulates segments
into datagrams
on rcving side, delivers
segments to transport
layer
network layer protocols
in every host, router
Router examines header
fields in all IP datagrams
passing through it
application
transport
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
application
transport
network
data link
physical
Network Layer 4-10
Key Network-Layer Functions
 forwarding: move
packets from router’s
input to appropriate
router output
 routing: determine
route taken by
packets from source
to dest.

analogy:
 routing: process of
planning trip from
source to dest
 forwarding: process
of getting through
single interchange
Routing algorithms
Network Layer
4-11
Interplay between routing and forwarding
routing algorithm
local forwarding table
header value output link
0100
0101
0111
1001
3
2
2
1
value in arriving
packet’s header
0111
1
3 2
Network Layer 4-12
Connection setup
 3rd important function in some network
architectures:

ATM, frame relay, X.25
 Before datagrams flow, two hosts and
intervening routers establish virtual
connection

Routers get involved
 Network and transport layer cnctn service:
 Network: between two hosts
 Transport: between two processes
Network Layer 4-13
Network service model
Q: What service model for “channel” transporting
datagrams from sender to rcvr?
Example services for
individual datagrams:
 guaranteed delivery
 Guaranteed delivery
with less than 40 msec
delay
Example services for a
flow of datagrams:
 In-order datagram
delivery
 Guaranteed minimum
bandwidth to flow
 Restrictions on
changes in interpacket spacing
Network Layer 4-14
Network layer service models:
Network
Architecture
Internet
Service
Model
Guarantees ?
Congestion
Bandwidth Loss Order Timing feedback
best effort none
ATM
CBR
ATM
VBR
ATM
ABR
ATM
UBR
constant
rate
guaranteed
rate
guaranteed
minimum
none
no
no
no
yes
yes
yes
yes
yes
yes
no
yes
no
no (inferred
via loss)
no
congestion
no
congestion
yes
no
yes
no
no
Network Layer 4-15
Virtual circuit vs. datagram
networks
Network Layer 4-16
Network layer connection and
connection-less service
 Datagram network provides network-layer
connectionless service
 VC network provides network-layer
connection service
 Analogous to the transport-layer services,
but:
Service: host-to-host
 No choice: network provides one or the other
 Implementation: in the core

Network Layer 4-17
Virtual circuits
“source-to-dest path behaves much like telephone
circuit”


performance-wise
network actions along source-to-dest path
 call setup, teardown for each call before data can flow
 each packet carries VC identifier (not destination host
address)
 every router on source-dest path maintains “state” for
each passing connection
 link, router resources (bandwidth, buffers) may be
allocated to VC
Network Layer 4-18
VC implementation
A VC consists of:
1.
2.
3.
Path from source to destination
VC numbers, one number for each link along
path
Entries in forwarding tables in routers along
path
 Packet belonging to VC carries a VC
number.
 VC number must be changed on each link.

New VC number comes from forwarding table
Network Layer 4-19
Forwarding table
VC number
22
12
1
Forwarding table in
northwest router:
Incoming interface
1
2
3
1
…
2
32
3
interface
number
Incoming VC #
12
63
7
97
…
Outgoing interface
2
1
2
3
…
Outgoing VC #
22
18
17
87
…
Routers maintain connection state information!
Network Layer 4-20
Virtual circuits: signaling protocols
 used to setup, maintain teardown VC
 used in ATM, frame-relay, X.25
 not used in today’s Internet
application
transport 5. Data flow begins
network 4. Call connected
data link 1. Initiate call
physical
6. Receive data application
3. Accept call
2. incoming call
transport
network
data link
physical
Network Layer 4-21
Datagram networks
 no call setup at network layer
 routers: no state about end-to-end connections
 no network-level concept of “connection”
 packets forwarded using destination host address
 packets between same source-dest pair may take
different paths
application
transport
network
data link 1. Send data
physical
application
transport
network
2. Receive data
data link
physical
Network Layer 4-22
Forwarding table
Destination Address Range
4 billion
possible entries
Link Interface
11001000 00010111 00010000 00000000
through
11001000 00010111 00010111 11111111
0
11001000 00010111 00011000 00000000
through
11001000 00010111 00011000 11111111
1
11001000 00010111 00011001 00000000
through
11001000 00010111 00011111 11111111
2
otherwise
3
Network Layer 4-23
Longest prefix matching
Prefix Match
11001000 00010111 00010
11001000 00010111 00011000
11001000 00010111 00011
otherwise
Link Interface
0
1
2
3
Examples
DA: 11001000 00010111 00010110 10100001
Which interface?
DA: 11001000 00010111 00011000 10101010
Which interface?
Network Layer 4-24
Datagram or VC network: why?
Internet
 data exchange among
ATM
 evolved from telephony
computers
 human conversation:
 “elastic” service, no strict
 strict timing, reliability
timing req.
requirements
 “smart” end systems
 need for guaranteed
(computers)
service
 can adapt, perform
 “dumb” end systems
control, error recovery
 telephones
 simple inside network,
 complexity inside
complexity at “edge”
network
 many link types
 different characteristics
 uniform service difficult
Network Layer 4-25
IP: Internet Protocol
Network Layer 4-26
The Internet Network layer
Host, router network layer functions:
Transport layer: TCP, UDP
Network
layer
IP protocol
•addressing conventions
•datagram format
•packet handling conventions
Routing protocols
•path selection
•RIP, OSPF, BGP
forwarding
table
ICMP protocol
•error reporting
•router “signaling”
Link layer
physical layer
Network Layer 4-27
IP Addressing: introduction
 IP address: 32-bit
identifier for host,
router interface
 interface: connection
between host/router
and physical link



router’s typically have
multiple interfaces
host may have multiple
interfaces
IP addresses
associated with each
interface
223.1.1.1
223.1.2.1
223.1.1.2
223.1.1.4
223.1.1.3
223.1.2.9
223.1.3.27
223.1.2.2
223.1.3.2
223.1.3.1
223.1.1.1 = 11011111 00000001 00000001 00000001
223
1
1
1
Network Layer 4-28
Subnets
 IP address:
 subnet part (high
order bits)
 host part (low order
bits)
 What’s a subnet ?
 device interfaces with
same subnet part of IP
address
 can physically reach
each other without
intervening router
223.1.1.1
223.1.2.1
223.1.1.2
223.1.1.4
223.1.1.3
223.1.2.9
223.1.3.27
223.1.2.2
LAN
223.1.3.1
223.1.3.2
network consisting of 3 subnets
Network Layer 4-29
Subnets
Recipe
 To determine the
subnets, detach each
interface from its
host or router,
creating islands of
isolated networks.
Each isolated network
is called a subnet.
223.1.1.0/24
223.1.2.0/24
223.1.3.0/24
Subnet mask: /24
Network Layer 4-30
Subnets
223.1.1.2
How many?
223.1.1.1
223.1.1.4
223.1.1.3
223.1.9.2
223.1.7.0
223.1.9.1
223.1.7.1
223.1.8.1
223.1.8.0
223.1.2.6
223.1.2.1
223.1.3.27
223.1.2.2
223.1.3.1
223.1.3.2
Network Layer 4-31
IP addressing: CIDR
CIDR: Classless InterDomain Routing
subnet portion of address of arbitrary length
 address format: a.b.c.d/x, where x is # bits in
subnet portion of address

subnet
part
host
part
11001000 00010111 00010000 00000000
200.23.16.0/23
Network Layer 4-32
IP datagram format
IP protocol version
number
header length
(bytes)
“type” of data
max number
remaining hops
(decremented at
each router)
upper layer protocol
to deliver payload to
how much overhead
with TCP?
 20 bytes of TCP
 20 bytes of IP
 = 40 bytes + app
layer overhead
32 bits
head. type of
length
ver
len service
fragment
16-bit identifier flgs
offset
upper
time to
Internet
layer
live
checksum
total datagram
length (bytes)
for
fragmentation/
reassembly
32 bit source IP address
32 bit destination IP address
Options (if any)
data
(variable length,
typically a TCP
or UDP segment)
E.g. timestamp,
record route
taken, specify
list of routers
to visit.
Network Layer 4-33
IP Fragmentation & Reassembly
 network links have MTU
(max.transfer size) - largest
possible link-level frame.
 different link types,
different MTUs
 large IP datagram divided
(“fragmented”) within net
 one datagram becomes
several datagrams
 “reassembled” only at final
destination
 IP header bits used to
identify, order related
fragments
fragmentation:
in: one large datagram
out: 3 smaller datagrams
reassembly
Network Layer 4-34
IP Fragmentation and Reassembly
Example
 4000 byte
datagram
 MTU = 1500 bytes
1480 bytes in
data field
offset =
1480/8
length ID fragflag offset
=4000 =x
=0
=0
One large datagram becomes
several smaller datagrams
length ID fragflag offset
=1500 =x
=1
=0
length ID fragflag offset
=1500 =x
=1
=185
length ID fragflag offset
=1040 =x
=0
=370
Network Layer 4-35
NAT: Network Address Translation
rest of
Internet
local network
(e.g., home network)
10.0.0/24
10.0.0.4
10.0.0.1
10.0.0.2
138.76.29.7
10.0.0.3
All datagrams leaving local
network have same single source
NAT IP address: 138.76.29.7,
different source port numbers
Datagrams with source or
destination in this network
have 10.0.0/24 address for
source, destination (as usual)
Network Layer 4-36
NAT: Network Address Translation
 Motivation: local network uses just one IP address as
far as outside word is concerned:
 no need to be allocated range of addresses from ISP:
- just one IP address is used for all devices
 can change addresses of devices in local network
without notifying outside world
 can change ISP without changing addresses of
devices in local network
 devices inside local net not explicitly addressable,
visible by outside world (a security plus).
Network Layer 4-37
NAT: Network Address Translation
Implementation: NAT router must:



outgoing datagrams: replace (source IP address, port
#) of every outgoing datagram to (NAT IP address,
new port #)
. . . remote clients/servers will respond using (NAT
IP address, new port #) as destination addr.
remember (in NAT translation table) every (source
IP address, port #) to (NAT IP address, new port #)
translation pair
incoming datagrams: replace (NAT IP address, new
port #) in dest fields of every incoming datagram
with corresponding (source IP address, port #)
stored in NAT table
Network Layer 4-38
NAT: Network Address Translation
2: NAT router
changes datagram
source addr from
10.0.0.1, 3345 to
138.76.29.7, 5001,
updates table
2
NAT translation table
WAN side addr
LAN side addr
1: host 10.0.0.1
sends datagram to
128.119.40, 80
138.76.29.7, 5001 10.0.0.1, 3345
……
……
S: 10.0.0.1, 3345
D: 128.119.40.186, 80
S: 138.76.29.7, 5001
D: 128.119.40.186, 80
138.76.29.7
S: 128.119.40.186, 80
D: 138.76.29.7, 5001
3: Reply arrives
dest. address:
138.76.29.7, 5001
3
1
10.0.0.4
S: 128.119.40.186, 80
D: 10.0.0.1, 3345
10.0.0.1
10.0.0.2
4
10.0.0.3
4: NAT router
changes datagram
dest addr from
138.76.29.7, 5001 to 10.0.0.1, 3345
Network Layer 4-39
NAT: Network Address Translation
 16-bit port-number field:

60,000 simultaneous connections with a single
LAN-side address!
 NAT is controversial:
 routers
should only process up to layer 3
 violates end-to-end argument
• NAT possibility must be taken into account by app
designers, eg, P2P applications
 address
IPv6
shortage should instead be solved by
Network Layer 4-40