Transcript TCP/IP Networks - Northern Kentucky University

CSC 382: Computer Security
TCP/IP
CSC 382: Computer Security
Slide #1
Topics
1.
2.
3.
4.
5.
6.
7.
8.
TCP/IP Layering
Encapsulation
Internet Addresses
Link Layer Protocols
IP
Routing
TCP and UDP
Application Layer Protocols
CSC 382: Computer Security
Slide #2
Network Example
A1
A2
A3
Router
B1
B2
CSC 382: Computer Security
External
Router
B3
Slide #3
TCP/IP Layering
Application
HTTP, FTP, telnet
Transport
TCP, UDP
Network
IP, ICMP, IGMP
Data Link
Physical
CSC 382: Computer Security
PPP, 802.11
Ethernet
Slide #4
TCP/IP Layers
1. Physical
–
NIC, cabling, electrical signaling.
2. Data Link
–
–
–
Single hop transport of packets.
Wired protocols (ethernet, FDDI, PPP)
Wireless protocols (802.11)
3. Network
–
–
End to end delivery of packets.
IP: Internet Protocol
CSC 382: Computer Security
Slide #5
TCP/IP Layers
4. Transport
–
–
–
Flow of data between two hosts for
application layer.
TCP: reliable data flow with
acknowledgements, retransmission, and
timeouts.
UDP: simpler service with no guarantees.
5. Application
–
–
Protocols for particular applications.
ex: FTP, HTTP, SMTP
CSC 382: Computer Security
Slide #6
Encapsulation/De-multiplexing
Sending: data sent down protocol stack
– Each layer prepends a header to data
– Ethernet frame sent as bit stream across wire
Receiving: data moves up protocol stack
– NIC moves bits into memory as ethernet frame
– Each layer removes its header from packet
CSC 382: Computer Security
Slide #7
Encapsulation
CSC 382: Computer Security
Slide #8
De-multiplexing
CSC 382: Computer Security
Slide #9
TCP/IP Security
TCP/IP has no built-in strong security.
–
–
–
–
No confidentiality features.
Minimal availability features (ToS options).
Insecure CRC checksums for integrity.
IPsec protocol extension adds security.
CSC 382: Computer Security
Slide #10
Data Link Layer
IEEE Standards
– Ethernet (802.3)
– Token Ring (802.5)
– Wireless (802.11)
Serial Protocols
– SLIP and CSLIP
– PPP
CSC 382: Computer Security
Slide #11
Hubs and Switches
Hubs
– Broadcast packets received to all interfaces.
Switches
– Associates MAC addresses with physical
interfaces.
– Sends packets only to specified interface.
– May have SPAN port for network monitoring.
CSC 382: Computer Security
Slide #12
Data Link Layer
Loopback
– Looks like any other link layer device.
– Full network processing is performed.
– Sends packets to localhost for testing.
48-bit MAC address
Maximum Transmission Unit (MTU)
– 1492 or 1500 bytes, depending on ethernet std
CSC 382: Computer Security
Slide #13
Promiscuous Mode
• All ethernet frames to or from any locally
connected host are seen by all hosts.
• NIC normally filters out frames that are not
addressed to its MAC address.
• In promiscuous mode, NIC processes all
ethernet frames, not just ones addressed to it.
– Requires administrative access on most OSes.
CSC 382: Computer Security
Slide #14
IP: Internet Protocol
Unreliable, connectionless datagram service
– Packets may arrived damaged, out of order,
duplicated or not at all.
– Transport/Application layers provide reliability.
IPv4 underlies Internet.
– 32-bit addresses in dotted-quad: 10.17.0.90.
– IPv6 is successor with 128-bit addresses.
Complexities: addressing, routing
CSC 382: Computer Security
Slide #15
IP Header
CSC 382: Computer Security
Slide #16
IP Header
Protocol version: IPv4
Header length: 5-60 32-bit words
Type of service (TOS):
– 3-bit precedence (ignored today)
– 4 TOS bits (min delay (telnet), max throughput
(ftp), max reliability, min monetary cost)
– unused 0 bit
CSC 382: Computer Security
Slide #17
IP Header
Total length: length of IP datagram (bytes)
– maximum size: 65535 bytes
– large packets fragmented at data link layer.
– small packets may be padded to minimum length.
TTL: upper limit on number of router hops.
Protocol: which protocol supplied packet data.
Header checksum: IP header checksum
CSC 382: Computer Security
Slide #18
IP Fragments
IP packets may be fragmented by routers for
transmission across different media.
– Max IP packet size: 65536
– Max Ethernet packet size: 1500
IP headers contain fragment data:
– Don’t Fragment Flag: 0=allowed, 1=don’t
– More Fragments Flag: 0=last, 1=more fragments
– Identification: identifies single packet for
reassembly.
– Fragment Offset: where contents of fragment go.
CSC 382: Computer Security
Slide #19
Internet Addresses
32-bit IPv4 addresses
– Dotted decimal notation: ii.jj.kk.ll
Divided into two parts
– Network ID
– Host ID
– XOR address with netmask to get Network ID.
Network ID
CSC 382: Computer Security
Host ID
Slide #20
Address Classes
Class A: 0.0.0.0-127.255.255.255
8-bit net ID, 24-bit host ID
Class B: 128.0.0.0-191.255.255.255
16-bit net ID, 16-bit host ID
Class C: 192.0.0.0-223.255.255.255
24-bit net ID, 8-bit host ID
Class D: 224.0.0.0-239.255.255.255
28-bit multicast group ID
Class E: 240.0.0.0-255.255.255.255
Reserved for future use
CSC 382: Computer Security
Slide #21
CIDR
Class addressing too inefficient
– Still need to aggregate routes to limit routing table size.
Example:196.1.1.0/24
– 24-bits of Net ID: 196.1.1
– Remaining 8-bits are host ID
Not limited to network class sizes
– Example: 192.168.128.0/22
– 4 class C networks: 192.168.{128,129,130,131}.0
CSC 382: Computer Security
Slide #22
Network Address Translation
Local network uses IETF reserved addresses.
– Non-routable: no router knows how to send packets to.
– RFC 1918: 10.x.y.z, 192.168.y.z, 172.16.y.z
Gateway translates reserved addresses to unique,
routable IP addresses.
– NAT: Dynamic mapping to pool of routable IP addresses.
• 10.0.0.1 -> 4.2.3.5
• 10.0.0.2 -> 4.2.3.6
– NAPT: Dynamic mapping to IP addresss/pool of src ports.
• 10.0.0.1 -> 4.2.3.5:1
• 10.0.0.2 -> 4.2.3.5:2
CSC 382: Computer Security
Slide #23
ARP: Address Resolution Protocol
MAC address determines packet destination.
How does network layer supply the link layer
with a MAC address?
ARP: Address Resolution Protocol
– Maps 32-bit IP addresses to 48-bit MAC addrs
– Data link layer protocol above ethernet
– RARP: Reverse ARP
CSC 382: Computer Security
Slide #24
ARP Example
sftp zappa.nku.edu
1. Obtains IP address via gethostbyname()
2. sftp asks TCP to connect to IP address
3. TCP sends connection request to brahms using an IP
datagram
4. Sending host emits ARP broadcast, asking for MAC
address of given IP address
5. Destination host’s ARP layer receives broadcast, answers
with an ARP reply w/ IP->MAC mapping
6. Sending host constructs ethernet frame with destination
MAC address containing IP datagram
7. Sending host sends IP datagram
CSC 382: Computer Security
Slide #25
ARP Cache
at204m02 (10.1.0.90) > arp -a
Net to
Device
-----hme0
hme0
hme0
hme0
hme0
Media Table: IPv4
IP Address
-------------------at_elan.lc3net
10.1.0.79
at204m02
10.1.7.103
10.1.0.139
CSC 382: Computer Security
Phys Addr
-----------------00:00:a2:cb:28:5e
00:e0:cf:00:0e:92
08:00:20:d8:e0:07
00:90:27:b6:b5:e5
00:e0:cf:00:15:bd
Slide #26
ARP Features
Proxy ARP
– Router can answer ARP requests on network B
for a host on network A that doesn’t see
broadcast.
Gratuitous ARP
– Host sends ARP for own IP address at boot.
– No reply should be received.
– Network misconfiguration if reply received.
CSC 382: Computer Security
Slide #27
IP Connectivity
No Network
– loopback only
Single LAN
– direct connectivity to hosts
Single Router
– Direct connectivity to local LAN
– Other networks reachable through one router
Multiple Routes to Other Networks
CSC 382: Computer Security
Slide #28
IP Routing
CSC 382: Computer Security
Slide #29
Routing Table
Where to send an IP packet to?
Use a table lookup: routing table
Search Process:
1. Search for a matching host address.
2. Search for a matching network address.
3. Search for a default route.
No route to destination: Host or network
unreachable error if search fails.
CSC 382: Computer Security
Slide #30
Routing Table
at204m02 (10.1.0.90) > netstat –rn
Routing Table: IPv4
Destination Gateway
Flags Ref
------------- -------------------10.1.0.0
10.1.0.90
U
1
224.0.0.0
10.1.0.90
U
1
default
10.1.0.1
UG
1
127.0.0.1
127.0.0.1
UH
6
CSC 382: Computer Security
Use
Int
----- ----4977 hme0
0 hme0
66480
798905 lo0
Slide #31
Routing Table
Destination: final destination host/network
Gateway: next host in route to destination
Flags
U: Route is up
G: Route is to a gateway (router)
H: Route destination is a host (not a network)
D: Route created by a redirect
M: Route modified by a redirect
CSC 382: Computer Security
Slide #32
Routing Table
10.1.0.0
direct access to local subnet
224.0.0.0
multicast route
default
forward packets to router at IP 10.1.0.1
127.0.0.1
loopback
CSC 382: Computer Security
Slide #33
IP Routing
Manual (static) routes
Added with the route command.
ICMP redirects can alter routes
Router sends ICMP redirect when packet should’ve been
sent to another router.
Routing protocols
Routers exchange routes with each other using special
routing protocols.
Full internet router tables contain ~30,000 routes.
Source routing
Sender includes routing info in packet header.
CSC 382: Computer Security
Slide #34
ICMP (Internet Control Message Protocol)
Network layer protocol encapsulated in IP
– Communicates error messages and exceptions.
– Messages handled by either IP or TCP/UDP.
IP Header (20 bytes)
ICMP Message
8-bit type
8-bit code
16-bit checksum
Contents
(always
depend
contains
on type and code
IP header + 8 data bytes)
CSC 382: Computer Security
Slide #35
ICMP Message Types
Type 0: echo (ping) reply
Type 3: destination unreachable
Type 4: source quench
Type 5: redirect
Type 8: echo (ping) request
Type 9, 10: router advertisement, solicitation
Type 11: time (TTL) exceeded
Type 12: parameter (header) problem
Type 13: timestamp
Type 14: timestamp reply
Type 15, 16: information request, reply
CSC 382: Computer Security
Slide #36
UDP: User Datagram Protocol
Simple datagram transport layer protocol.
Each application output generates one UDP
datagram, which produces one IP datagram.
Trades reliability for speed
Sends datagrams directly to unreliable IP layer.
16-bit port numbers
Identify sending and receiving processes.
Applications
DNS, SNMP, TFTP, streaming audio/video
CSC 382: Computer Security
Slide #37
UDP Header
CSC 382: Computer Security
Slide #38
UDP Example: TFTP
Trivial File Transfer Protocol
No authentication
TFTP Session:
sun16 > tftp at204m02
tftp> get readme.txt
Received 1024 bytes in 0.2 seconds.
tftp> quit
CSC 382: Computer Security
Slide #39
TFTP Packet Types
Packet types
1)
2)
3)
4)
5)
read a file (filename, ascii/binary)
write a file (filename, ascii/binary)
file data block
ACK
error
CSC 382: Computer Security
Slide #40
TFTP Packet Diagram
CSC 382: Computer Security
Slide #41
TFTP Session Trace
at204m02 > snoop udp sun16
1 0.00000 sun16 -> at204m02
(netascii)
TFTP Read "2sun"
2
0.00498 at204m02 -> sun16
(512 bytes)
TFTP Data block 1
3
0.00136
TFTP Ack block 1
4
0.00010 at204m02 -> sun16
(300 bytes) (last block)
5
sun16 -> at204m02
0.00119
sun16 -> at204m02
CSC 382: Computer Security
TFTP Data block 2
TFTP Ack block 2
Slide #42
TFTP Security
Feature: no username/password required
TFTP used for diskless hosts to boot.
How to protect /etc/passwd?
Limit TFTP server filesystem access.
Generally only can access /tftpboot directory.
CSC 382: Computer Security
Slide #43
TCP: Transmission Control Protocol
Connection-oriented
Must establish connection before sending data.
3-way handshake.
Reliable byte-stream
TCP decides how to divide stream into packets.
ACK, timeout, retransmit, reordering.
16-bit source and destination ports.
FTP(21), HTTP(80), POP(110), SMTP(25)
CSC 382: Computer Security
Slide #44
TCP Reliability
1. Breaks data into best-sized chunks.
2. After sending segment, maintains timer; if no
ACK within time limit, resends segment.
3. Sends ACK on receipt of packets.
4. Discards pkts on bad checkum of header and
data.
5. Receiver resequences TCP segments so data
arrives in order sent.
6. Receiver discards duplicate segments.
7. Flow control: only sends as much data as
receiver can process.
CSC 382: Computer Security
Slide #45
TCP Header
CSC 382: Computer Security
Slide #46
TCP Header
• Sequence Number: 32-bit segment identifier.
• Acknowledgment: next sequence number
expected by sender of ACK
– TCP is full duplex so both sides of connection
have own set of sequence numbers
• Header length: length of header in 32-bit
words (20bytes default–60bytes w/ options)
• Window size: number of bytes receiver is
willing to accept (flow control)
CSC 382: Computer Security
Slide #47
TCP Header Flags (Code Bits)
URG: urgent pointer is valid
ACK: acknowledgement number is valid
PSH: rcvr should pass data to app asap
RST: reset connection
SYN: synchronize sequence numbers to
initiate a connection
FIN: sender is finished sending data
CSC 382: Computer Security
Slide #48
TCP Options
End of option list (kind=0)
NOP (kind=1)
Used to pad fields to 32-bit boundary
Maximum Segment Size (MSS) (kind=2)
Len=4 (length includes kind + len bytes)
16-bit MSS
Default: 536 data + 20 TCP hdr + 20 IP hdr
Window Scale Factor (kind=3)
Timestamp (kind=8)
CSC 382: Computer Security
Slide #49
TCP Connections
Establishment
3-way handshake
Connection Trace
Termination
Normal Termination
Connection Trace
Reset
CSC 382: Computer Security
Slide #50
Connection Establishment Protocol
1. Requester (client) sends a SYN segment,
specifying the port number of the server to
which it wants to connect and the client’s initial
sequence number (ISN).
2. Server responds with SYN segment containing
server’s ISN. Server acknowledges client’s
SYN by ACKing the client’s ISN+1.
3. Client acknowledges server SYN by ACKing
server’s ISN+1.
CSC 382: Computer Security
Slide #51
TCP 3-way Handshake
CSC 382: Computer Security
Slide #52
Connection Establishment Test
at204m02> /usr/sbin/snoop sun09
at204m02> nc sun09 22
SSH-1.99-OpenSSH_3.7.1p2
^C
If no services running, start your own:
at204m02> nc -l -p 8192
CSC 382: Computer Security
Slide #53
TCP Connection Trace
at204m02 -> sun09 TCP D=22 S=37519
Syn Seq=477982308 Len=0 Win=24820
Options=<nop,nop,sackOK,mss 1460>
sun09 -> at204m02 TCP D=37519 S=22
Syn Ack=477982309 Seq=3227257622
Len=0 Win=24820
Options=<nop,nop,sackOK,mss 1460>
at204m02 -> sun09 TCP D=22 S=37519
Ack=3227257623 Seq=477982309 Len=0
Win=24820
CSC 382: Computer Security
Slide #54
Connection Termination Protocol
As TCP is full duplex, each side must
terminate half of the connection as follows:
Send FIN segment (active close)
Other side ACKs w/ FIN sequence number +1
Half-closed connections
Side that sent FIN can still receive data.
Example: ssh fasthost sort < words.txt
CSC 382: Computer Security
Slide #55
TCP Disconnection
CSC 382: Computer Security
Slide #56
Connection Termination Test
at204m02> /usr/lib/sendmail -bd
at204m02> /usr/sbin/snoop port 25
sun09>nc at204m02 25
220 at204m02.lc3net ESMTP
Sendmail 8.11.7+Sun/8.11.7; Mon,
29 Mar 2004 14:09:40 -0500 (EST)
quit
CSC 382: Computer Security
Slide #57
TCP Disconnection Trace
at204m02 -> sun09
TCP D=33042 S=25 Fin
Ack=3597541820 Seq=872479258 Len=0
Win=24820
sun09 -> at204m02
TCP D=25 S=33042
Ack=872479259 Seq=3597541820 Len=0
Win=24820
sun09 -> at204m02
TCP D=25 S=33042 Fin
Ack=872479259 Seq=3597541820 Len=0
Win=24820
at204m02 -> sun09 TCP D=33042 S=25
Ack=3597541821 Seq=872479259 Len=0
Win=24820
CSC 382: Computer Security
Slide #58
TCP Reset
Connection Refused
> telnet at204m02 8192
Trying 10.1.0.90...
telnet: Unable to connect to remote host:
Connection refused
Packet Trace
sun09 -> at204m02
TCP D=8192 S=33048
Syn Seq=3848454475 Len=0 Win=24820
Options=<nop,nop,sackOK,mss 1460>
at204m02 -> sun09
TCP D=33048
S=8192 Rst Ack=3848454476 Win=0
CSC 382: Computer Security
Slide #59
TCP Reset (cont.)
Connection Abort
Any queued data is thrown away.
Other side is informed of abnormal close.
Packet Detail:
One side sends RST.
Other side aborts connection.
There is no ACK sent in response.
CSC 382: Computer Security
Slide #60
Half-Open Connections
Connections where one side has aborted or
closed connection w/o knowledge of other.
– Client or server host has crashed.
– DOS attack: requester sends SYN, doesn’t
respond to SYN+ACK.
CSC 382: Computer Security
Slide #61
Example List of TCP Ports
TCP: IPv4 (netstat –na output)
Local Addr Rmt Addr State
---------- -------------------*.111
*.*
LISTEN
*.32771
*.*
LISTEN
*.32772
*.*
LISTEN
*.32773
*.*
LISTEN
*.32774
*.*
LISTEN
*.4045
*.*
LISTEN
*.22
*.*
LISTEN
*.2049
*.*
LISTEN
*.515
*.*
LISTEN
*.80
*.*
LISTEN
*.6000
*.*
LISTEN
*.22
10.17.0.23.32827
ESTABLISHED
*.2049 10.17.0.23.799
ESTABLISHED
CSC 382: Computer Security
Slide #62
TCP Servers
Local Address
*.80 means that it will accept connections on any network
interface on TCP port 80.
Foreign Address
*.* means that the server will accept connections from
any source host and port.
Conn=(src IP, src port, dst IP, dst port)
All connections to same server will have same dst IP and
port, but will have different source IPs and ports
Kernel maintains queue of ~5 incoming connections
for each server.
CSC 382: Computer Security
Slide #63
Key Points
1. TCP/IP Layers: encapsulation/de-multiplexing
1.
2.
3.
4.
Physical/Data Link: ethernet, PPP
Network: IP, ICMP
Transport: UDP, TCP
Application: ftp, http, smtp, telnet, etc.
2. IP
1. Addressing: DNS/IP/MAC, netmasks, CIDR, NAT.
2. Routing: tables, hubs/switches/routers.
3. TCP
1. Connection and Termination: 3-way handshake
2. Addressing: source and destination ports.
CSC 382: Computer Security
Slide #64
References
1.
2.
3.
4.
5.
6.
7.
8.
K. Egevang and P. Francis, “The IP Network Address Translator
(NAT),” RFC 1631, http://www.ietf.org/rfc/rfc1631.txt, 1994.
J.B. Postel, “Internet Protocol,” RFC 791,
“http://www.ietf.org/rfc/rfc0791.txt, 1981.
J.B. Postel, “Internet Control Message Protocol,” RFC 792,
“http://www.ietf.org/rfc/rfc0792.txt, 1981.
J.B. Postel, “Transmission Control Protocol,” RFC 793,
http://www.ietf.org/rfc/rfc0793.txt, 1981.
Ed Skoudis, Counter Hack, Prentice Hall, 2002.
Richard Stevens, TCP/IP Illustrated, Vol. 1, Addison-Wesley, 1994.
Richard Stevens, UNIX Network Programming, Vol. 1, PrenticeHall, 1998.
Andrew Tannenbaum, Computer Networks, 4th edition, PrenticeHall, 2002.
CSC 382: Computer Security
Slide #65