Transcript Document

Chapter 2
The OSI Model and
the TCP/IP Protocol Suite
Objectives
Upon completion you will be able to:
• Understand the architecture of the OSI model
• Understand the layers of the OSI model and their functions
• Understand the architecture of the TCP/IP Protocol Suite
• Differentiate between the OSI model and the TCP/IP Suite
• Differentiate between the three types of Internet addresses
TCP/IP Protocol Suite
1
2.1 The OSI Model
Established in 1947, the International Standards Organization (ISO) is a
multinational body dedicated to worldwide agreement on international
standards. An ISO standard that covers all aspects of network
communications is the Open Systems Interconnection (OSI) model. It
was first introduced in the late 1970s.
The topics discussed in this section include:
Layered Architecture
Peer-to-Peer Processes
Encapsulation
TCP/IP Protocol Suite
2
Note:
ISO is the organization.
OSI is the model
TCP/IP Protocol Suite
3
Figure 2.1
TCP/IP Protocol Suite
The OSI model
4
Figure 2.2
TCP/IP Protocol Suite
OSI layers
5
Figure 2.3
TCP/IP Protocol Suite
An exchange using the OSI model
6
2.2 Layers in the OSI Model
The functions of each layer in the OSI model is briefly described.
The topics discussed in this section include:
Physical Layer
Data Link Layer
Network Layer
Transport Layer
Session Layer
Presentation Layer
Application Layer
Summary of Layers
TCP/IP Protocol Suite
7
Figure 2.4
TCP/IP Protocol Suite
Physical layer
8
Note:
The physical layer is responsible
for the movement of individual bits
from one hop (node) to the next.
TCP/IP Protocol Suite
9
Figure 2.5
TCP/IP Protocol Suite
Data link layer
10
Note:
The data link layer is responsible for
moving frames from one hop (node) to
the next.
TCP/IP Protocol Suite
11
Figure 2.6
TCP/IP Protocol Suite
Hop-to-hop delivery
12
Figure 2.7
TCP/IP Protocol Suite
Network layer
13
Note:
The network layer is responsible for
the delivery of individual packets from
the source host to the destination host.
TCP/IP Protocol Suite
14
Figure 2.8
TCP/IP Protocol Suite
Source-to-destination delivery
15
Figure 2.9
TCP/IP Protocol Suite
Transport layer
16
Note:
The transport layer is responsible for
the delivery of a message from one
process to another.
TCP/IP Protocol Suite
17
Figure 2.10
TCP/IP Protocol Suite
Reliable process-to-process delivery of a message
18
Figure 2.11 Session layer
TCP/IP Protocol Suite
19
Figure 2.12
TCP/IP Protocol Suite
Presentation layer
20
Figure 2.13
TCP/IP Protocol Suite
Application layer
21
Figure 2.14
TCP/IP Protocol Suite
Summary of layers
22
2.3 TCP/IP Protocol Suite
The TCP/IP protocol suite is made of five layers: physical, data link,
network, transport, and application. The first four layers provide physical
standards, network interface, internetworking, and transport functions
that correspond to the first four layers of the OSI model. The three
topmost layers in the OSI model, however, are represented in TCP/IP by
a single layer called the application layer.
The topics discussed in this section include:
Physical and Data Link Layers
Network Layer
Transport Layer
Application Layer
TCP/IP Protocol Suite
23
Figure 2.15
TCP/IP Protocol Suite
TCP/IP and OSI model
24
2.4 Addressing
Three different levels of addresses are used in an internet using the
TCP/IP protocols: physical (link) address, logical (IP) address, and
port address.
The topics discussed in this section include:
Physical Address
Logical Address
Port Address
TCP/IP Protocol Suite
25
Figure 2.16
TCP/IP Protocol Suite
Addresses in TCP/IP
26
Figure 2.17
TCP/IP Protocol Suite
Relationship of layers and addresses in TCP/IP
27
Example 1
In Figure 2.18 a node with physical address 10 sends
a frame to a node with physical address 87. The two
nodes are connected by a link. At the data link level
this frame contains physical (link) addresses in the
header. These are the only addresses needed. The rest
of the header contains other information needed at
this level. The trailer usually contains extra bits
needed for error detection.
See Next Slide
TCP/IP Protocol Suite
28
Figure 2.18
TCP/IP Protocol Suite
Physical addresses
29
Example 2
As we will see in Chapter 3, most local area networks
use a 48-bit (6 bytes) physical address written as 12
hexadecimal digits, with every 2 bytes separated by a
colon as shown below:
07:01:02:01:2C:4B
A 6-byte (12 hexadecimal digits) physical address.
TCP/IP Protocol Suite
30
Example 3
In Figure 2.19 we want to send data from a node with network
address A and physical address 10, located on one LAN, to a
node with a network address P and physical address 95, located
on another LAN. Because the two devices are located on
different networks, we cannot use link addresses only; the link
addresses have only local jurisdiction. What we need here are
universal addresses that can pass through the LAN
boundaries. The network (logical) addresses have this
characteristic.
See Next Slide
TCP/IP Protocol Suite
31
Example 3 (Continued)
The packet at the network layer contains the logical addresses,
which remain the same from the original source to the final
destination (A and P, respectively, in the figure). They will not
change when we go from network to network. However, the
physical addresses will change as the packet moves from one
network to another. The boxes labeled routers are
internetworking devices, which we will discuss in Chapter 3.
See Next Slide
TCP/IP Protocol Suite
32
Figure 2.19
TCP/IP Protocol Suite
IP addresses
33
Example 4
As we will see in Chapter 4, an Internet address (in
IPv4) is 32 bits in length, normally written as four
decimal numbers, with each number representing 1
byte. The numbers are separated by a dot. Below is an
example of such an address.
132.24.75.9
An internet address in IPv4 in decimal numbers
TCP/IP Protocol Suite
34
Example 5
Figure 2.20 shows an example of transport layer
communication. Data coming from the upperlayers
have port addresses j and k ( j is the address of the
sending process, and k is the address of the receiving
process). Since the data size is larger than the network
layer can handle, the data are split into two packets,
each packet retaining the service-point addresses ( j
and k). Then in the network layer, network addresses
(A and P) are added to each packet.
See Next Slide
TCP/IP Protocol Suite
35
Example 5 (Continued)
The packets can travel on different paths and arrive at
the destination either in order or out of order. The two
packets are delivered to the destination transport
layer, which is responsible for removing the network
layer headers and combining the two pieces of data
for delivery to the upper layers.
See Next Slide
TCP/IP Protocol Suite
36
Figure 2.20
TCP/IP Protocol Suite
Port addresses
37
Example 6
As we will see in Chapters 11, 12, and 13, a port
address is a 16-bit address represented by one decimal
number as shown below.
753
A 16-bit port address represented as one single number.
TCP/IP Protocol Suite
38
2.5 IP Versions
IP became the official protocol for the Internet in 1983. As the Internet
has evolved, so has IP. There have been six versions since its inception.
We look at the latter three versions here.
The topics discussed in this section include:
Version 4
Version 5
Version 6
TCP/IP Protocol Suite
39