Transcript H8800P WEB BASE CONFIGURATION

Quick Installation Guide for Hurricane8800P
( For Singapore Users )
A. Hardware Installation
Console Port
Line Jack
For Phone Cable (Rj-11) , to connect to ADSL Line
For Serial Cable (RS-232) , to connect
to Serial Port
(Normally , no need to connect it)
Power Connector
LAN Connectors
For Lan Cable (Rj-45) , to connect to
PCs Network Card
ADSL
TEL
Microfilter
(2-way splitter)
Phone Jack
Phone Cable (RJ11)
*Plug the given microfilter into the connector
marked
at the back of the router.
Connect the phone cable RJ-11 from the
microfilter label “ADSL” to the main phone
socket & another RJ-11 from “Tel” to your
telephone line jack.
*For surfing only , you may connect the phone cable directly to
the router without going thru the microfilter .
Power Point
5V Power
Adapter
Connect the given Power adaptor to the Jack
marked
and then switch on the power
point.
The console port is connected using the
RJ–232 serial cable for configuration
purposes. Normally you do not need to
connect it.
User is recommended to use the Web-based
management to configure. Please refer to the
back page for more information.
Straight RJ-45
Cable
Straight RJ-45
Cable
Laptop RJ-45
Connection
Desktop RJ-45
Connection
1. Turn off the computer.
2. Plug the end of the Ethernet cable RJ-45
into any one connector marked 1 2 3 4 at the
back of the router.
3. Plug the other end of the Ethernet cable
into your computer's RJ-45 jack of the
Ethernet card. Turn on the PC.
*You may connect to a Hub/Switch to have more
than 4 PCs connected.
After connecting up as shown on 1 ,2
and 3 , you should see the following
lights on the router
Power LED (In red color)
Light ON once detected
*ADSL LED (In green color)
Light ON when the connection is ON
LAN LED X 4 (In green color)
Keeps ON, Light blinks during data
transfer
*If ADSL LED fail to light UP.
CHECK1 : All telephones sharing the same ADSL line are attached with microfilters each
CHECK2 : ADSL account is activated and your ADSL line condition
(check with your ISP if you’re unsure)
B. Configure Your PCs
Specify a static IP for your individual PCs.
For Windows 95/98/ME
Go To Control Panel >Network>TCP/IP of your LAN card > Properties
Select TCP/IP
of your Lan
Card and
then click
Properties
*Set IP Address to
192.168.101.X
(X : 2~254)
Set Subnet Mask
to 255.255.255.0
Add Gateway to
192.168.101.1
Enable DNS server
Host : pc
Remember to
click on the
Add button
Add Singnet/Pacnet
DNS 165.21.83.88
*IP Address for each PC MUST BE Unique. Example PC 1 IP add is 192.168.101.2 , therefore PC 2 IP add should be 192.168.101.3 and so forth.
For Windows 2000/XP
Click the Start button and then Control Panel. From there,
click the Network and Internet Connections icon. Then click
the Network Connections icon
Select the Local Area
Connection icon for the
applicable Ethernet adapter
and then do a Right Click
and select Properties
Key in the IP Add ,
Subnet Mask ,
Gateway and DNS
Server as follow
Select Internet
Protocol(TCP/IP) and
then Click Properties
Note : The router is OS Independent
C. Web-Based Configuration
Open Internet Explorer/Netscape , type in http://192.168.101.1
Notes:
i) You may have to disable the proxy settings on your internet browser.
ii) For IE user , go to Tools> Internet Options>Connections>Choose Never
dial a connection>go to LAN Settings>Disable Proxy Server
ii) For Netscape user , click Edit>Preferences>Advanced>Proxies>Choose
Direct connection to the Internet
The system will remind you to
enter the administrator ’s
username and password
when restarting or configuring.
Default username: admin
password: admin
Click Add Interface
under Security
Interface
Add LAN Interface
•Name: ppp-0
•Interface
Type:external
Click Apply
The configuration of
PPPoA Router mode has
been done
*Click Router mode under
Configuration and choose
PPPOA routed. Then click
Configure
(i) Description: Name of the
WAN connection. (e.g. SingNet)
Click Add Interface
under Security
Interface again
(ii) Choose CHAP
(iii) User name and Password:
The user name and password
will be provided by your ISP
when applying for ADSL service.
(e.g.prolink@singnet )
(iv) The rest of the settings will
be in default
Add WAN Interface
•Name : eth-0 or ip1
•Interface Type :
Choose internal
Click Apply
(v) Click the Configure button
Click Security. Choose
Enable under Security State
and click Change State
.
Click Enable NAT to
internal interfaces
NOTE: Please remember to
save the configuration after
finishing the settings.
Click Save Config and then
click the Save button to store
your settings
*Pls refer to the manual for
the configuration of other
routing modes.