Transcript عرض تقديمي من PowerPoint

Introduction in Prosthodontics
(dental prosthetics)
Dr. Waseem Bahjat Mushtaha
Specialized in prosthodontics
Introduction:
Prosthesis: an artificial appliance which
replace lost or congenitally missing tissue.
Some prosthesis restore both function and
appearance of tissue they replace other
merely restore one of these factors.
Prosthetics: is the art and science of designing
and fitting artificial substitutly to replace
lost or missing tissue.
Prosthodontics (dental prosthetics):
Is the branch of dental art and science which
with the replacement of missing teeth and
oral tissue to restore and maintain oral form,
function, appearance, phonetics and health.
Complete denture prosthodontics:
involves an artificial replacement of the lost
natural dentition and associated structures
of the maxilla and mandible for patient who
has lost all their remaining natural teeth.
Function of complete denture:
1- Mastication: chew food for swallowing and
digestion.
2- Speech (phonetics): the teeth either natural or
artificial assist the tongue and lips to form
some of the sounds of speech.
3- Appearance (aesthetic): is influence by the
shape of jaws together with the position and
occlusal relation ship of the teeth.
4- Health of the alveolar bone and the tempromandibular joints (T.M.J).
Complete dentures have three
structures:
1- The fitting surface.
2- The occlusal surface.
3- The polished surface.
Anatomy and physiology in relation
to complete denture
I- oral mucosa membrane (tissue compression)
1- The bone of the upper and lower edentulous
jaws are covered with a soft tissues and the
oral cavity is lined with soft tissue known as
mucosa membrane.
2- This mucosa membrane is composed of two
layer mucosa and sub mucosa.
3- Mucosa consists of stratified squamous
epithelium.
4- The thickness and consistency of the sub
mucosa are largely responsible for the
support denture.
5- In the edentulous patient the crest of
residual alveolar ridge + hard palate has
masticatory mucosa have firmly attached
to the supporting bone.
6- The sub mucosa in the region in the median
palatine suture of the maxillary bone is
extremely thin so will become inflamed
when wearing denture.
II- the alveolar ridges
1) The residual ridge consists of:
1- Denture – bearing mucosa.
2- Sub mucosa
3- Periostem
4- Under laying residual alveolar bone.
Types of alveolar ridges and palate
formation:
I- upper ridges
1- well – developed (upper ridge) but not
abnormally thick ridges and palate with a
moderate vault.
2- Flat –v- shaped palate usually associated
with bulky ridge.
3- Flat palate with small ridge and shallow.
4- Ridge exhibiting gross under cut area.
II- lower ridge
1- Broad and well developed lower ridges.
2- Ridges exhibiting under cut areas.
3- Well developed but narrow or knife
edged ridges.
4- Flat ridge.
Anatomical land marks of complete
dentures
I- INTRA ORAL ANATOMICAL LAND
MARK
II- EXTRA ORAL LANDMARK
Upper denture
I- INTRA ORAL ANATOMICAL
LAND MARK
1- Stress bearing (supporting area).
2- Peripheral or limiting (sealing) areas
Incisive papilla
I- supporting structure
1- Incisive papilla:
1) It is the elevation of the tissue that covers the incisive
foramens (the opening of the nasopalatine canal which,
carry the nasopalatine vessels and nerves).
2) Location, on the median line behind and between the
central incisors.
3) In old edentulous mouth it is located on the center of the
ridge due to resorption.
4) It may require relief in the finished denture base to prevent
irritation of the nasopalatine nerve.
2- Rugae area
2- Rugae area:
1) The rugae are irregular shaped rolls of soft
tissue.
2) Location, lie in the anterior part of the hard
palate.
3) It is considered a secondary stress- bearing
area for the upper complete denture.
4) With the natural dentitions, it assists
formation of sounds like the
in
letter s.
Residual alveolar ridge
3- Residual alveolar ridge
1) The residual alveolar ridge and most of the hard palate are considered
the major or primary stress bearing area in the upper jaw.
2) The crest of the residual ridge is covered with layer of fibrous
connective tissue which is most favorable for supporting the
denture because of it is firmness and position.
3) The crest of ridge is described as a primary stress-bearing area and
most tolerated to resisting the denture movement and resulting
irritation
Median palatine raphe
4- Median palatine raphe:
1) It is median suture formed by the union of
the palatine processes of maxilla and
horizontal plates of the palatine bones.
2) It is covered with mucosa membrane and
little sub mucosa tissue.
3) This area may require selective relief with
in denture base.
5- The tuberosities
5- The tuberosities
1) The posterior part of the maxillary alveolar
ridge forms prominence called the
tuberosity.
2) It is usually a bulbous extension of the
residual ridge in the second and third molar
region.
3) Terminating hamular notch.
4) Large tuberosities bounded by deep salci
offer very satisfactory denture
5) Tuberosities exhibiting gross undercuts
may require surgical treatment.
6) They are identified in the finished denture
by the tubercular fossa.
6- Fovea palatinae
6- Fovea palatinae:
1) These are indentations near the midline of
the palate formed.
2) They are close to the vibrating line and
always in soft tissue.
3) Which makes an ideal guide for the ending
of the posterior border of the denture
7- Tours palatinus
7- Tours palatinus:
1) At the junction of the palatine process of the
maxillary bone, in the midline or on each side
lateral to the midline.
2) A bony projection is some times observed.
3) It varies in size and form.
4) If it is too large it should be surgically removed.
5) If it is small the denture base should be relieved
of that area.
Border structures that limit the
periphery of the upper denture
(limiting structure)
1- The maxillary labial frenum:
1) It is a fibrous bond covered by mucosa
membrane that extends from the labial aspect of
the residual alveolar ridge to the lip.
2) It has no muscle fiber and has no action of it is
own.
3) The labial in the labial flange of the denture must
be just wide and deep enough to allow the
frenum to pass through it without manipulation
of the lip.
The maxillary labial frenum
2- Labial vestibule and labial flange:
1) The labial flange of maxillary denture occupies a
potential space bounded by: labial aspect of the
residual alveolar ridge, the muco-labial alveolar
fold, and the orbicularis oris muscle.
2) The length of this flange should not extend
beyond the normal drape of the muco-labial fold.
3) The thickness of the flange depends up on the
degree of alveolar resorption.
4) The denture border area between the labial
frenum and the buccal frenum is known as the
maxillary labial flange.
2- Labial vestibule and labial flange
3- Buccal frenum:
1) It is a some times a single fold of mucosa
membrane, sometimes double and in some
mouths, broad and fan shaped.
2) The buccal notch in the denture must be broad
enough to allow the movement of the buccal
frenum.
3) Inadequate provision for the buccal frenum or
excess thickness of the flange distal to the
buccal notch can cause dislodgment of the
denture when the cheeks are moved posterioly
as in abroad smile.
Buccal frenum
4- Buccal vestibule:
1) It is extended from the buccal frenum to the hamular notch.
2) It houses the buccal flange of the denture.
3) This space between the ridge and cheek.
4) The buccal flange of maxillary denture should fill but not over fill it.
5) The thickness of the distal end of the buccal flange of the denture must
be adjusted to accommodate the ramus and cronoid process and
masseter muscle as they function.
The distal end of the buccal flange must not be too thick because the
ramus will push the denture out of the place during opening or lateral
movement of mandible.
Buccal vestibule
5- Pterygomaxillary (hamular) notch
1) It is formed by the pterygoid process of
sphenoid bone and the posterior end of
maxilla, back to the tuberosity.
2) It is used as boundary of the posterior
border of maxillary denture.
3) It is important for sealing.
Pterygomaxillary (hamular) notch
6- Vibrating line of the palate
1) It is an imaginary line drawn across the
posterior part of the palate that marks the
beginning of motion in the soft palate
when the patients say "ah".
2) It extends from one pterygomaxillary notch
to other.
3) It is not the junction between hard and soft
palate. It is always in soft palate.
Vibrating line of the palate
7- Posterior palatal border (Potsdam)
1) The distal edge of the maxillary denture base
terminates in the posterior palatal seal area.
2) This denture edge generally ends at or before the
vibrating line.
3) The seal of this border must be situated in the
region of compressible tissue just distal to the
hard palate. (But it must be anterior to the
vibrating line).
Posterior palatal border (Potsdam)
8- The soft palate
Patient may be broadly divided in to classes
with regard to non mobile area:
1) Those whose palates exhibit movement at
the junction of the hard palate and soft
palate.
2) Those whose soft palates move some
distance behind the junction.
The width of the area available for the posterior palatal seal
will depend up on the curvature of the soft palate. There
are three classes of curvature of soft palate:
Glass I: the soft palate has a gentle curvature and
allows for abroad posterior palatal seal area.
Glass II: the soft palate has a medium curvature and allow for
a medium width of the posterior palatal seal area.
Glass III: the soft palate has a sharp and abrupt
curvature and allows for a narrow
posterior palatal seal area.
The soft palate
II- lower denture
Intra oral structures that support the lower
denture (supporting structure):
1) Residual alveolar ridge:
The crest of the residual alveolar ridge is
covered by fibrous connective tissue, but in
many mouths the under lying bone is and
without a good bony plate covering it.
2) External oblique ridge
1- It is a bony ridge.
2- It begins at the junction of alveolar ridge and the
ramus of the mandible.
3- It descends obliquely downward and
across the outer surface of the
forward
body.
4- It fades out at appoint nearly opposite the mesial
surface of the first molar.
5- It is recorded in the impression and wed as
appoint reference in the impression making.
3) The buccal shelf of bone
1- Location: it is the area between the mandibular buccal frenum and the
anterior edge of masseter
2- This area is bonded:
- Medially: the crest of residual ridge.
- Anteriorly: buccal frenum.
- Laterally: external oblique ridge.
- Distally: retromolar pad.
3- The buccal shelf offers excellent resistance to forces (primary stress
bearing area of the mandibular denture) due to:
- It is at right angles to the vertical occlusal forces.
- Very wide.
- It is covered with good smooth cortical bone.
4) Retromolar region and pad:
1- It is a triangular soft pad of tissue at the distal
end of the lower ridge.
2- It must be covered by denture base.
3- Sealing the retromolar pad aids in the stability of
the denture.
5) Mylohyoid ridge (internal oblique ridge):
1- It descends obliquely down and across the inner
surface of the body of the mandible.
2- It begins in the region of the third molar and
continuous downwards and forwards to the
lower border of the mandible near the midline.
6) Mental foramen
1- location: on the buccal surface of the
mandible in the premolar region.
2- Mental nerves and vessels pass thought it.
3- In cases of extreme ridge resorption it is
usually located on the crest of the ridge.
4- Pressure from the denture may cause pain
and numbness (require relief in finished
denture)
7) Torus mandibularis
1- It is bony projection.
2- Sometimes found on the lingual surface in
the premolar region.
3- If it is too large it will require surgical
removal.
4- If small, the denture should be relived in
that area.
Border structures that limit the
periphery of the lower denture
(limiting structures)
1) The mandibular labial frenum:
1- It is a band of fibrous connective tissue that
helps to attach the orbicularis oris
(muscle of the lip)
2- It is accommodated by a groove in the
mandibular denture.
2) The mandibular vestibule and labial flange:
The part of the denture that extends
between the labial notch and the buccal
notch is called the mandibular labial
flange.
3) Buccal frenum:
1- This attachment connects with continuous
band through the corner of the mouth
And on up to the buccal frenum of the
maxilla.
4) Buccal vestibule and buccal flange:
1- It extends from the buccal frenum posteriorly to
the out side back corner of the retromolar pad
and from the crest of the residual alveolar ridge
to the cheek.
2- It houses the buccal flange of the mandibular
denture.
5) Masseter muscle influence area:
1- The distobuccal corner of the mandibular
denture must coverage rapidly to avoid
displacement due to contracting pressure of the
masseter muscle.
(Whose anterior fibers pass out side buccinator in
this region)
6) Lingual flange area (alveolingual sulcus):
The distal extention of the lingual flange lies in the lingual pouch.
Lingual pouch (retromylohoid fossa):
Is the area bounded medially by the tongue, laterally by the mandible,
posteriorlly by the palatoglussus arch, which is formed in part by the
palatoglossus muscle and in part by the lingual extention of the
superior constructor muscle and anteriorly by the posterior 3 mm of the
mylohoid muscle. Forward on the lingual extension, the area is
influence by the mylohoid muscle, which attaches to the mylohoid
ridge. The flange extends below and medially from the mylohoid ridge
to fill the fold formed by the tongue and the tissue of the floor of the
mouth.
This means that the inner surface of this flange does not rest on mucosa
membrane over bone, but on soft tissue. It leaves the bony attachment
at the mylohoid ridge, and the flange extends out under the tongue to
fill the fold. The forward part of the flange area of this region over the
sublingual stand usually is shallow because of the movement of the
tissue that is controlled indirectly by the mylohoid muscle.
7) Lingual frenum
1- It is anterior attachment of the tongue.
2- Very resistant and active and often wide.
3- It needs complete functional trimming to
avoid having the attachment displace the
lower denture.