Auxiliary Views ( Curved Edges)

Download Report

Transcript Auxiliary Views ( Curved Edges)

Auxiliary Views (Curved Edges)
The same procedure (steps1-10) discussed before applies for curved edges.
However, curved edges have no corners, so we take points on the curved edges
and treat them like corners. The more points we take, the better the drawing of the
Curved edges.
Take the following examples.
Surface A
Surface A
LOS
E
Draw a true shape of surface A ( i .e we need an
auxiliary view where LOS is Perpendicular to surface A.
1
10'
9'
6' 5'
8' 7'
4'
3'
2'
- choose points on curved edges
11
1
+
- connect projection lines between views
10
2
9
8 7 6 5 4
3
2
3
4
5
6
7
8
9
10
11
1
2
9'
8' 7' 6' 5' 4'
10'
- Choose LOS ( in this case LOS is
perpendicular to surface A to get true shape)
3'
2'
11
1
+
- Draw projection lines from chosen points
on curved edges parallel to LOS.
10
2
9
4
8 7
6 5
3
2
3
4
5
6
7
8
9
10
11
1
9'
3
8' 7' 6' 5' 4'
10'
- Draw RL1 perpendicular to projection lines // LOS
3'
2'
11
1
+
- Draw RL1 perpendicular to projection lines
between the two views.
10
2
9
8 7 6 5 4
3
RL2
2
3
4
5
6
7
8
RL1
9
10
11
1
4
9'
8' 7' 6' 5' 4'
10'
3'
2'
- Measure distance from RL2
11
- Transfer distance to RL1
3’
4’
2’
1
+
1
5’
6’
10
2
7’
8’
2
9
8 7 6 5 4
3
RL2
3
9’
4
10’
5
6
7
11
10
9
8
2
3
4
5
6
7
8
RL1
9
10
11
1
5
9'
8' 7' 6' 5' 4'
10'
- Connect points
2'
11
2’
3’
4’
3'
1
+
1
5’
6’
10
7’
2
8’
2
9
8 7 6 5 4
3
RL2
3
9’
4
10’
5
6
7
11
10
9
8
2
3
4
5
6
7
8
RL1
9
10
11
1
OR
3'
10'
9'
8' 7' 6' 5' 4'
2'
11
- Draw RL1
3'
1
+
RL2
- Draw RL1
2
10
9
4
8 7
6 5
3
2
3
RL1
4
5
6
7
8
9
10
11
1
OR
10'
4'
9'
8' 7' 6' 5' 4'
2'
11
5’
4’
3’
2’
1
+
- Measure distance from RL1
- Transfer distance to RL1
3'
RL2
1
2
10
9
6’
7’
2
8’
3
8 7 6 5 4
3
9’
4
5
10’
6
7
11
RL1
2
8
10
9
3
4
5
6
7
8
9
10
11
1
OR
5'
10'
9'
8' 7' 6' 5' 4'
2'
11
• Connect Point
1
+
RL2
2’
3’
4’
3'
1
2
10
5’
9
6’
7’
3
8 7 6 5 4
2
8’
3
9’
4
10’
5
6
7
11
RL1
10
9
2
8
3
4
5
6
7
8
9
10
11
1
Run //CE-WSINST
Auxiliary View
http://faculty.kfupm.edu.sa/CE/almanasa/
Run //CE-WSINST
Complete
Partial
(1)
Identify line of sight
(2)
Draw reference line
(3)
Project lines from each view
(1)
Create layers (1)  Choose color for projection.
(2)
Create layers (2)  Choose another color for
point numbers.
Draw offset  Through (any distance) and choose
point for RL 2 & RL 1
-
-
-
Choose layer for text  Give the
Same Number on all layer
Go to Tool pull down  drafting
setting  object snap 
perpendicular
OR ONSAP  setting 
perpendicular (SELECT)
Go to Construction layer (1)
Type DI (distance) or from the Tool
bar add Inquiry bar & choose DI
-
-
Go perpendicular  Go offset same dist. up and
draw
Extent line to new point  Give a point number as
text.
For curved line choose PL commands to draw lines
Type PEDIT  Choose line (to show it smooth
curve)  F
To change some lines to hidden .
Modify  properties  Line type  hidden
Mirror
Choose line  shift choose ….. specify 1st
point
2nd point around the x-x line Enter