Transcript 슬라이드 1

SPECIFICATIONS
MEMO
USER’S MANUAL
SDD-DAW30IR
Signal Format
NTSC
Horizontal Resolution
800TVL
Image Sensor
1/3” SONY 960H Dual Scan CCD
Effective Pixels
976(H) x 494(V)
Scanning System
2:1 Interlace
Synchronization
Internal
Scanning Frequency
15.734KHz(H), 59.94Hz(V)
Video Output
CVBS : 1.0Vp-p/75Ω
Min. Illumination
Color : 0.1Lux/F1.2 (Sens-up x512 : 0.0002Lux/F1.2)
B/W : 0.08Lux/F1.2 (Sens-up x512 : 0.000015Lux/F1.2)
Electronic Shutter
Speed
Iris Control
S/N Ratio
Backlight
Compensation
1/60 ~ 1/10,000sec
COLOR IR DOME CAMERA
PAL
976(H) x 582(V)
15.625KHz(H), 50.00Hz(V)
1/50 ~ 1/10,000sec
MANUAL
52dB
BLC / HLC / OFF
White Balance
ATW (1,800°K~10,500°K) / PUSH / USER1 / USER2 /
ANTI CR / MANUAL / PUSH LOCK
Gain Control
Level Setting
2D+3D DNR
OFF / LOW / MID LOW / MID / MID HIGH / HIGH
Day & Night
AUTO ( INT / EXT1 / EXT2 ) / DAY / NIGHT
Sens-up
Auto ( x2 ~ 256x ) / OFF
WDR
OFF / ON
Digital Zoom
Digital Pan/Tilt
Flickerless
OFF / AUTO / ON
Motion Detection
OFF / ON (4 Area)
Privacy
15 Area (W/ Mosaic etc.)
Mirror
OFF / VFLIP / HFLIP / HVFLIP
Sharpness
Level Setting
Camera ID
OFF / ON
Communication
RS-485 ( Pelco-D ) / Coax ( Pelco-C )
OSD
Eng / Jpn / Ger / Ita / Rus / Spn / Por / Chi
Lens
Fixed Lens 3.6mm
IR LED
30pcs
Power Supply
DC 12V (±10%)
Power Consumption
LED Off : Max. 1.8W / LED On : Max. 2.8W
Operating Temperature -10°C ~ +50°C
Operating Humidity
Less than 90%
Dimension
130(Ø) x 105(H)mm
Weight
Approx. 305g
* In accordance with customers’ request and OSD controller’s option, the specifications can be fixed or changed without notice.
SDD-DAW30IR
FEATURES
• 1/3＂SONY 960H Dual Scan CCD
• High Resolution of 800TV Lines
• Min. Illumination of 0.0002Lux at F1.2 (Sense-up)
• Day & Night
• WDR : Wide Dynamic Range
• 2D+3D DNR : 2D+3D Digital Noise Reduction
• HLC : High Light Compensation
• DIS : Digital Image Stabilizer
• Motion Detection
• Privacy Mask
• Digital Pan / Tilt
• 30pcs IR LED
• Fixed Lens 3.6mm
• 3-Axis Gimbal Bracket
• Option : OSD Controller / Coaxial Communcation (PELCOC)
Dual Voltage (DC 12V / AC 24V)
PRECAUTIONS
NAME OF EACH PART
• Do not install the camera in extreme temperature conditions.
- Only use the camera under conditions where temperatures are
between -10°Cand +50°C. Be especially careful to provide
ventilation
when operating under high temperatures.
UPPER
OSD CONTROL (Option- BOARD / CABLE)
BOTTOM
Video loop-out
a
Lens
Screw hole
IR LED
• Do not install or use the camera in an environment where the
humidity is high.
- It can cause the image quality to be poor.
OSD Controller
Dome cover
a. SET :
Displays the menu on the screen. Press this switch to confirm
status or
after changing a selected item.
Dome base
• Never use the camera close to a gas or oil leak.
- It can cause malfunctions to occur.
• Do not disassemble the camera.
- There are no user-serviceable parts inside it.
• Never keep the camera face to strong light directly.
- It can damage the image sensor.
• Do not drop the camera or subject them to physical shocks.
- It can cause malfunctions to occur.
b. UP / DOWN :
Used to move the cursor up or down in the menu screen to select
a
desired menu item.
INSTALLATION
c. LEFT / RIGHT :
Used to move the cursor left or right in the menu screen or to
change
the value of the selected item.
CAMERA ASSEMBLY
1. Install the camera with the screw.
2. Adjust the camera direction.
3. Assemble the dome cover into the camera.
DIMENSION
1
2
3
• Do not expose the camera to rain or spill beverage on it.
- If it gets wet, wipe it dry immediately. Liquids can contain minerals
that
corrode the electronic components.
• Do not expose the camera to radioactivity.
- If exposed to radioactivity the image sensor will fail.
CONNECTION
* NOTE *
•If the camera is exposed to spotlight or object reflecting strong light,
smear or blooming may occur.
• Please check that the power satisfies the normal specification
before
connecting the camera.
Power input (DC 12V)
Video output (Connecting to monitor)
COMPOSITION
3-AXIS GIMBAL BRACKET
• Pan rotation :
Adjusting the horizontal angle. (360°)
• Tilt rotation :
Adjusting the vertical angle. (100°)
Camera
Screw
Video cable
Cover opener
Power cable
Manual
R
DOWN
Cable hole
• Do not install the camera under unstable lighting conditions.
- Severe lighting change or flicker can cause the camera to work
improperly.
• Do not touch the front lens of the camera.
- It is one of the most important parts of the camera. Be careful not
to be
stained by fingerprint.
UP
L
• Camera rotation :
Adjusting the horizontal position of the
screen.
(360°)
100˚
360˚
360˚