Transcript **** 1

NAME
MODEL
제조사
Open Architecture D.S.P
EDGE
SYMETRIX
• Processors: 1 x Analog Devices SHARC 21489 @ 400 MHz SIMD.
• Raw processing capacity: 400 MIPS, 1.6 GFLOPS.
• Sampling Rate: 48 kHz, ± 100 ppm.
• Frequency Response (A/D/A): 20 Hz – 20 kHz, ± 0.5 dB.
• Dynamic Range (A/D/A): > 114 dB, A-weighted.
• Channel Separation (A/D/A): > 108 dB @ 1 kHz, +24 dBu.
• Latency (A/D/A): 0.88 mS, inputs routed to outputs.
Four configurable I/O card slots, up to 16 channels total
of local I/O plus 128 (64x64) channels of Dante network audio.
• Delay memory: 80 mono seconds.
• Analog control inputs: 0-3.3 VDC.
• Recommended external control potentiometer: 10k Ohm, linear.
• Logic outputs: Low (0V) when active, pulled high (5V) when inactive.
• Logic output maximum external power supply voltage: 24 VDC.
• Logic output maximum external power supply current sinking: 50 mA.
• Logic output maximum output current: 10 mA.
• RS-232 accessory serial I/O: 38.4 kbaud (default), 8 data bits, 1 stop bit, no parity,
no flow control wired straight-through, only pins 2, 3, and 5 required.
• RS-485 serial I/O: 38.4 kbaud (default) 8 data bits, 1 stop bit, no parity, no flow
control. May be broken out of ARC port.
• Ethernet Cable: Standard CAT5, maximum device to device length = 100 meters.
• Dante Cable: Standard CAT6, maximum device to device length = 100 meters.
• ARC Cable: Standard CAT5, distance dependent upon load and number of devices.
• Maximum devices per system: 32 units per Site File.
• Maximum stored presets: 1000.
• Operating Temperature
: 30°C
• Power
: 100-240 VAC, 50/60 Hz, 45 w
• Dim(WxHxD)
: 480.2 x 43.7 x 241.3mm(1U)
• Shipping Weight : 5.9kg
NAME
MODEL
제조사
4Channel AEC Input card
• Number of Inputs
: Four (4) acoustic echo cancellation.
• Connectors
: 3.81 mm terminal blocks.
• Nominal Input Level
: +4 dBu with 20 dB of headroom.
• Maximum Input Level
: +23 dBu.
• Mic Pre-amp Gain
: 0, 11.8, 24, 44 or 54 dB switchable
with ± 24 dB trim.
• Mic Pre-Amp EIN
: <-127dB with 150 Ohm source impedance.
• CMRR
: > 76 dB @ 1 kHz, unity gain.
• Input Impedance
: 8k Ohms balanced, 4k Ohms unbalanced.
• Phantom Power
: +20 VDC @ 10 mA maximum.
• A/D Dynamic Range
: < 115 dB, A-weighted.
• A/D Latency
: 0.28 mS (direct), 11 mS (AEC enabled).
• A/D THD + Noise
: < -94 dB, unweighted
• Tall Length
: >250mS.
• Convergence Time
: >100dB/S.
• Shipping Weight
: 0.45kg
EDGE Option Card
4ch AEC INPUT
SYMETRIX
NAME
MODEL
제조사
4 Channel analog input card
• Number of Inputs
: Four (4) switchable balanced mic or line level.
• Connectors
: 3.81 mm terminal blocks.
• Nominal Input Level
: +4 dBu with 20 dB of headroom.
• Maximum Input Level
: +23 dBu.
• Mic Pre-amp Gain
: 0, 11.8, 24, 44 or 54 dB switchable
with ± 24 dB trim.
• Mic Pre-Amp EIN
: < -127dB with 150 Ohm source impedance.
• CMRR
: > 76 dB @ 1 kHz, unity gain.
• Input Impedance
: 8k Ohms balanced, 4k Ohms unbalanced.
• Phantom Power (per input)
: +48 VDC @ 10 mA maximum.
• Dynamic Range
: > 115 dB, A-weighted.
• THD + Noise
: < -94 dB, unweighted; 1 kHz @ +22 dBu
with 0 dB gain.
• Latency
: 0.28 mS.
• Shipping Weight
: 0.45kg
EDGE Option Card
4ch Analog MIC/LINE INPUT
SYMETRIX
NAME
MODEL
제조사
4Channel analog output card
• Number of Outputs
: Four (4) balanced line level.
• Connectors
: 3.81 mm terminal blocks.
• Nominal Output Level
: +4 dBu with 20 dB of headroom.
• Maximum Output Level
: +24 dBu
(+22.8 dBu into a 2k Ohm minimum load).
• Output Impedance
: 300 Ohms balanced, 150 Ohms unbalanced.
• Dynamic Range
: > 117 dB, A-weighted.
• THD + Noise
: < -95 dB, unweighted; 1 kHz @ +22 dBu
with 0 dB gain.
• Latency
: 0.60 mS.
• Shipping Weight
: 0.45kg
EDGE Option Card
4ch Analog MIC/LINE OUTPUT
SYMETRIX
NAME
EDGE Option Card
MODEL
4ch Digital INPUT
제조사
4Channel digital input card
• Number of Inputs
: Two (2) pairs of switchable AES or S/PDIF
format (4 channels total).
• Connectors
: 3.81 mm terminal blocks.
• Nominal Input Level
: -20 dBFS (+4 dBu with 20 dB of headroom).
• Maximum Input Level
: 0 dBFS (+24 dBu).
• Input Impedance
: 110 Ohms (AES), 75 Ohms (S/PDIF).
• Dynamic Range
: > 128 dB, unweighted.
• THD + Noise
: < -125 dB, unweighted.
• Nominal Sample Rate
: 48 kHz.
• Sample Rate Sync Range
: 12 to 96 kHz.
• Latency
: 2.1 mS @ 48 kHz.
• Shipping Weight
: 0.45kg
SYMETRIX
NAME
MODEL
제조사
4Channel digital output card
• Number of Outputs
: Two (2) pairs of switchable AES or S/PDIF
format (4 channels total).
• Connectors
: 3.81 mm terminal blocks.
• Nominal Output Level
: -20 dBFS (+4 dBu with 20 dB of headroom).
• Maximum Output Level
: 0 dBFS (+24 dBu).
• Output Impedance
: 110 Ohms (AES), 75 Ohms (S/PDIF).
• Dynamic Range
: > 128 dB, unweighted.
• THD + Noise
: < -125 dB, unweighted.
• Nominal Sample Rate
: 48 kHz.
• Sample Rate Sync Range
: 12 to 96 kHz.
• Latency
: 2.1 mS @ 48 kHz.
• Shipping Weight
: 0.45kg
EDGE Option Card
4ch Digital OUTPUT
SYMETRIX
NAME
MODEL
제조사
2 Line analog telephone interface card
• Telco “Line” Connector
: RJ11. Format: POTS (plain old telephone
service) or analog extension from a PBX.
• Telco “Set” Connector
: RJ11. Format: POTS (plain old telephone
service) or analog extension from a PBX.
Note: Relay bridged to Line port with option
in software to isolate based on hook status.
• Frequency Response
: 250 Hz to 3.3 kHz ±1.0 dB
• THD+N
: < 0.3%
• Signal to Noise Ratio
: > 62 dB
• LEC Tail Time
: 32 mS
• Null
: 55 dB nominal.
• Compliance
: G.165, G.168 compliant.
• Tx Level
: -10.0 dBm RMS average; +3.2 dBm maximum.
• Rx Level
: -10.0 dBm RMS average; +3.2 dBm maximum.
• Transhybrid Loss
: > 48 dB with LEC enabled.
• Ringer Equivalency Number
: 0.0 dB
• Shipping Weight
: 0.45 kg
EDGE Option Card
2 LINE ANALOG TELEPHONE INTERFACE
SYMETRIX
NAME
MODEL
제조사
12 mic/line inputs
• Sampling Rate
: 48 kHz, ± 100 ppm.
• Frequency Response (A/D)
: 20 Hz – 20 kHz, ± 0.5 dB.
• Channel Separation (A/D)
: > 111 dB @ 1 kHz, +24 dBu.
• Dante Cable
: Standard CAT6, maximum device to device
length = 100 meters.
• Connector
: 3.81 mm terminal blocks.
• Number of inputs
: 12 switchable balanced mic or line level.
• Nominal input level
: +4 dBu with 20 dB of headroom.
• Maximum input level
: +23 dBu.
• Mic pre-amp gain
: 0, 11.8, 24, 44 or 54 dB switchable.
• Mic pre-amp EIN
: < -127 dB with 150 Ohm source impedance.
• CMRR
: > 76 dB @ 1 kHz, unity gain.
• Input impedance
: 8k Ohms balanced, 4k Ohms unbalanced.
• Phantom power (per input)
: +48 VDC @ 10 mA maximum.
• Dynamic range
: > 116 dB, A-weighted.
• THD + Noise
: < -100 dB, unweighted; 1 kHz @ +22 dBu
with 0 dB gain.
• Latency
: 0.28 mS.
• Operating Temperature
: 30°C
• Power
: 100-240 VAC, 50/60 Hz, 25 w
• Dim(WxHxD)
: 480.2 x 43.7 x 241.3mm(1U)
• Shipping Weight
: 5.4kg
Open Architecture D.S.P
xIN 12
SYMETRIX
NAME
MODEL
제조사
Open Architecture D.S.P
RADIUS 12x8
SYMETRIX
• Analog Inputs: Twelve (12) switchable balanced mic or line level.
• Analog Outputs: Eight (8) balanced line level.
• Processors: 1 x Analog Devices SHARC 21489 @ 400 MHz SIMD.
• Raw processing capacity: 400 MIPS, 1.6 GFLOPS.
• Sampling Rate: 48 kHz, ± 100 ppm.
• Frequency Response (A/D/A): 20 Hz – 20 kHz, ± 0.5 dB.
• Dynamic Range (A/D/A): > 114 dB, A-weighted.
12 mic/line inputs, 8 outputs.
• Channel Separation (A/D/A): > 108 dB @ 1 kHz, +24 dBu.
• Latency (A/D/A): 0.88 mS, inputs routed to outputs.
• Delay memory: 80 mono seconds.
• Analog control inputs: 0-3.3 VDC.
• Recommended external control potentiometer: 10k Ohm, linear.
• Logic outputs: Low (0V) when active, pulled high (5V) when inactive.
• Logic output max. external power supply voltage/Current sinking: 24VDC/50 mA.
• Logic output maximum output current: 10 mA.
THD + Noise: < -85 dB (unweighted); 1 kHz @ +22 dBu with 0 dB gain.
RS-232 accessory serial I/O: 57.6 kbaud (default), 8 data bits, 1 stop bit, no parity, no
flow control wired straight-through, only pins 2, 3, and 5 required.
• RS-485 serial I/O: 38.4 kbaud (default) 8 data bits, 1 stop bit, no parity, no flow
control. May be broken out of ARC port.
• Ethernet Cable: Standard CAT5, maximum device to device length = 100 meters.
• Dante Cable: Standard CAT6, maximum device to device length = 100 meters.
• ARC Cable: Standard CAT5, distance dependent upon load and number of devices.
• Maximum devices per system: 32 units per Site File.
• Maximum stored presets: 1000.
• Operating Temperature
: 30°C
• Power
: 100-240 VAC, 50/60 Hz, 45 w
• Dim(WxHxD)
: 480.2 x 43.7 x 241.3mm(1U)
• Shipping Weight : 5.9kg
NAME
MODEL
제조사
12 line outputs
• Sampling Rate: 48 kHz, ± 100 ppm.
• Frequency Response (D/A): 20 Hz – 20 kHz, ± 0.5 dB.
• Channel Separation (D/A): > 111 dB @ 1 kHz, +24 dBu.
• Dante Cable: Standard CAT6, maximum device to device length = 100 meters.
• Connector: 3.81 mm terminal blocks.
• Number of outputs: Twelve (12) balanced line level.
• Nominal output level: +4 dBu with 20 dB of headroom.
• Maximum output level: +24 dBu (+22.8 dBu into a 2k Ohm minimum load).
• Output impedance: 300 Ohms balanced, 150 Ohms unbalanced.
• Dynamic range: > 118 dB, A-weighted.
• THD + Noise: < -105 dB, unweighted; 1 kHz @ +22 dBu with 0 dB gain.
• Latency: 0.60 mS.
• Operating Temperature: 30°C
• Power: 100-240 VAC, 50/60 Hz, 25 w
• Dim(WxHxD): 480.2 x 43.7 x 241.3mm(1U)
• Shipping Weight: 5.4kg
Open Architecture D.S.P
xOUT 12
SYMETRIX
NAME
MODEL
제조사
Menu-driven wall panel remote for Symetrix D.S.P
• 8-character backlit display supports up to 31 scrolling characters.
• Instant user feedback for control assignments, default settings, and actions.
• Three buttons navigate menus, change values, and enable or disable the remote
control.
• All control assignments, including item labeling, parameter limits and firmware
version upgrades are handled by software included with Symetrix DSP hardware.
• Processor
: Atmel ATmega 128
• Field-Upgradeable Firmware
: Yes
• Number of Menus
: 24
• Enumerations per Menu
: 16
• Menu Range Limits
: Yes
• Max. Characters per Menu Name
: 31
• Maximum Number of Strings
: 255
• Maximum Operating Voltage
: 30 VDC
Adaptive Remote Control
ARC-2e
SYMETRIX
NAME
MODEL
제조사
Rotary encoder remote with two-bank push-button knob.
• 8-segment LED ladder with push-button encoder can control one or two parameters.
• Power, control, and a single channel of ARC Audio are connected via RJ-45 inputs.
• Supports “idle” mode for light-sensitive environments like theaters.
• Hardware lockout pins are provided to accommodate an installer supplied key
switch. Software and hardware lockout functions can be independently programmed.
• Furnished with a standard white single gang Decora® faceplate and splash resistant
overlay.
Adaptive Remote Control
ARC-K1e
SYMETRIX
NAME
Four push-button wall panel remote.
• Four switches are programmable as momentary, latched or radio buttons with tricolor LEDs.
• Power, control, and a single channel of ARC Audio are connected via RJ-45 inputs.
• Supports “idle” mode for light-sensitive environments like theaters.
• Hardware lockout pins are provided to accommodate an installer supplied key
switch. Software and hardware lockout functions can be independently programmed.
• Furnished with a standard white single gang Decora® faceplate and splash resistant
overlay.
Adaptive Remote Control
MODEL
ARC-SW4e
제조사
SYMETRIX
NAME
Push-button remote expansion panel.
• Remote wall panel expansion device for use with ARC-K1e and ARC-SW4e.
• For expansion, add up to four ARC-EX4e to each ARC-K1e and up to three ARCEX4e to each ARC-SW4e.
• Cost effective way to expand remote control capabilities.
• Not for use with ARC-2e.
• Splash resistant overlay.
Adaptive Remote Control
MODEL
ARC-EX4e
제조사
SYMETRIX