Transcript analog multimeter

Chapter 6
Electrical Measurements ─ Meters
Objectives
• After completing this chapter, you will be
able to:
– Identify the two types of meter movements
available
– Describe how a voltmeter is used in a circuit
– Describe how an ammeter is used in a circuit
– Describe how an ohmmeter is used for
measuring resistance
Objectives (cont’d.)
– Identify the functions of a multimeter
– Identify the advantages/disadvantages of
DMMs and VOMs
– Describe how to use a multimeter to measure
voltage, current, and resistance
– Describe how to measure current using an
ammeter
– Describe how to connect an ammeter into a
circuit
Objectives (cont’d.)
– List safety precautions for using an ammeter
– Describe how to connect a voltmeter to an
electrical circuit
– List safety precautions for connecting a
voltmeter to a circuit
– Describe how resistance values are
measured using an ohmmeter
– Define continuity check
Objectives (cont’d.)
– Describe how an ohmmeter is used to check
open, short, or closed circuits
Introduction to Meters
• Analog meter
– Uses a graduated scale with a pointer
– Provides better graphic display of rapid
changes in current/voltage
• Digital meter
– Provides a reading in numbers
– More accurate than analog meters
Types of Meters
Figure 6-5. The placement of an ammeter in a circuit.
Types of Meters (cont’d.)
Figure 6-6. (A) Schematic symbol for a voltmeter.
(B) A voltmeter is connected in parallel in a circuit.
Types of Meters (cont’d.)
Figure 6-7. (A) Schematic symbol for an ohmmeter. (B) An ohmmeter applies
a voltage across the component being measured and monitors the current
flowing through it.
Multimeters
• Multimeter
– Combines a voltmeter, ammeter, and
ohmmeter into one package
• VOM (volt-ohm-milliammeter)
– An analog multimeter that measures volts,
ohms, and milliamperes
• DMM
– A digital multimeter
5 Voltage positions
4 current positions &
3 resistance positions
Function
switch
+DC, -DC, AC
Figure 6-8. An analog multimeter.
DMM
Multimeters (cont’d.)
• Advantages of DMMs over VOMs:
– Easier readability, resulting in a higher
accuracy with smaller voltage
– Autoranging capabilities (does not need to
identify range of signal to be tested)
– Autozeroing for resistance reading
– Autolock of a displayed value
Multimeters (cont’d.)
• Disadvantages of a DMM:
– Requirement for batteries or other source of
electricity
– Voltage limitation; if exceeded could damage
the meter.
– Inability to measure an instantaneous change
in a signal faster than the sampling time
Measuring Current
Figure 6-9. An ammeter is connected in series to a circuit.
Red: +
Black: -
Connect - To - & + to +
Pointer from left to right.
Reverse leads if needle
moves in opp. direction
Figure 6-10. An ammeter is one part of this VOM. A black negative lead plugs into the
common or negative hack. A red positive lead plugs into the jack with the plus symbol.
Measuring Current (cont’d.)
• Caution:
– Always turn off power before connecting an
ammeter to a circuit
– An analog ammeter must never be connected
in parallel with any ckt component (s/c; fuse
will blow & damage to meter)
– Never connect an ammeter directly to a
voltage source (s/c)
• Internal resis of Ammeter adds to ckt resis.
So measured current reduces.
Measuring Voltage
Figure 6-13. When connecting a voltmeter into a circuit, be sure to observe polarity.
• Polarity is imp. Connect + to +. Reverse
the leads if pointer goes from right to left.
• Voltmeter’s internal resis. is in parallel with
resis of component to be measured. So eq
resis reduces. So V measured reduces.s
Measuring Resistance
Figure 6-14. When using an ohmmeter to measure resistance, the component being
measured must be removed from the circuit.
Measuring Resistance (cont’d.)
• Continuity test (or check)
– Determines if current path is continuous
– Open circuit
• Indicates high resistance
– Short circuit
• Zero ohms of resistance
– Closed circuit
• Indicates low resistance
• Advantages of DMM:
1. higher accuracy
2. Digital readout
3. Repeatability of reading
4.Uses very little current to test resis.
5. uses audio signal for continuity test
Reading Meter Scales
• Full scale value
– Maximum value indicated by a meter
• Ammeters and voltmeters
– Read from left to right
– Linear scales
• Ohmmeters
– Read from right to left
– Nonlinear scales
Summary
• Analog meters use a graduated scale with
a pointer
• Digital meters provide a direct readout
• A multimeter combines a voltmeter,
ammeter, and ohmmeter into one package
• A VOM is an analog multimeter
• A DMM is a digital multimeter
Summary
• On a multimeter, the range selector switch
selects the function to be used
• An ammeter must be connected in series
with a circuit
• A voltmeter is connected in parallel with a
circuit
• An ohmmeter measures resistance by
applying a known voltage