Transcript Folie 1 - Sirona Support

X-Ray Webinar 3/27/2013
X-Ray update
Topics of the day
-
Online preventative maintenance.
-
Calibration backup
-
SUI updates
-
Schick Update
Yearly PM now live on-line also for X-Ray units
-
Required for 3D units covered by service contracts
- Same log-in as for CAD/CAM units
- Just choose “Imaging Products” on the left
- Look for the correct manual for your unit.
- Print out the checklist if you wish
Yearly PM now live on-line also for X-Ray units
Yearly maintenance (1)
Electrical/Mechanical check: (Follow the manual)
-
Check serial number of unit (bottom right of unit)
-
Check all buttons and lights and audible tone(s).
(Dead-man switch release button).
Yearly maintenance (2)
-
Electrical check: (Follow the manual)
-
Measure Power outlet adequacy
(voltage drop).
-
Tip: Can be measured later while you do the dose check
in calibration.
Yearly maintenance (3)
Depending
on Galileos
machinelaser
there
- - Attention:
Check lasers
The
can
(Galileos) to four
canbe
beone
obstructed
(XG3D
Ceph)(if
lasers.
by headrest
present).
(Take it out now, it must
be removed for calibration
anyway).
Yearly maintenance (4)
All good so far ?
Relax…
… a minute
Yearly maintenance (5)
-
Before you start:
-
Make sure you have all calibration phantoms !
Pin Phantom (XG3D)
Geometry Phantom (XG3D, Galileos)
Distortion Phantom (Galileos)
Yearly maintenance (6)
Ceph Phantom (XG3D Ceph)
Constancy test (XG3D, Galileos)
2D !
Yearly maintenance (7)
-
Go to sironasupport.com
Video page:
Yearly maintenance (8)
-
Make a backup of the calibration data !!!
If you don’t and the calibration fails, the unit will not work anymore.
Yearly maintenance (9)
-
Go through ALL steps start to finish, regardless if the
symbols are green, yellow or red!
(Except radiation field).
Galileos:
Tool can be downloaded
from web-site:
Sironasupport.com
Yearly maintenance (10)
-
Perform the Acceptance or Constancy test:
-
Sidexis -> Utilities -> Acceptance/Constancy test
Coming up: SUI updates (Software update image)
-
One Moment………...
Ready?
SUI updates (1)
-
“SUI update” refers to the installation/upgrade of the
“firmware” of any XG/Galileos X-Ray system.
Sidexis Manager -> SiXabcon
-
Attributes -> software update.
-
Select SW package you want to add. 4.07…4.12
SUI updates (2)
Do not pay too much attention
to “red” and “green”
BUT: Boards that show V00.00
as their actual version might
have an issue.
There is a third way to update
units: Modul-update which can
be advantageous.
ALWAYS IGNORE:
Timout “vermutet” (expected).
Wait until update is finished.
SUI updates (2)
-
When do you need a SUI update?
3D machines: With (almost) every (PC) software update.
Spareparts!
- come with “random” software loaded, not necessarily
matching the unit.
Unit old – sparepart new.
Unit brand new – sparepart older.
Attention: Sometimes SUIs have to be upgraded in steps…
SUI updates (3)
-
What to do?
Update/downgrade the spare part to unit Software?
Update the unit to (newer) spare part Software?
Technical
ThisCALL
can both SIRONA
be dangerous!!!
service!!
Older SW might not support newer units/parts, upgrading to newest
SUI might lead to malfunctions with (older) PC software.
-
Thank you !!