No Slide Title
Download
Report
Transcript No Slide Title
COMS W4995-1
Lecture 3
IP Addressing
Today:
IP addressing
Data link protocols and ARP
Notes about lab
IP Addressing
Addressing defines how addresses are
allocated and the structure of addresses
IPv4
Classful IP addresses (obsolete)
Classless inter-domain routing (CIDR) (RFC
854, current standard)
IP Version 6 addresses
What is an IP Address?
Why Addresses?
End-to-end argument (principle)
Reading:
http://web.mit.edu/Saltzer/www/publications/endtoend/endtoend.pdf
Keep it Simple, Stupid
What is an IP Address?
An IP address is a unique global address for a
network interface.
An IP address uniquely identifies a network
location.
http://www.arin.net/whois
http://www.iana.org/ipaddress/ip-addresses.htm
Routers forwards a packet based on the
destination address of the packet.
IPv4 Addresses
32 bits
v ersion
(4 bits)
header
length
Type of Serv ice/TOS
(8 bits)
flags
(3 bits)
Identification (16 bits)
TTL Time-to-Liv e
(8 bits)
Total Length (in bytes)
(16 bits)
Protocol
(8 bits)
Fragment Offset (13 bits)
Header Checksum (16 bits)
Source IP address (32 bits)
Destination IP address (32 bits)
Ethernet Header
IP Header
TCP Header
Ethernet frame
Application data
Ethernet Trailer
IP v.4 Addresses
32 bits
0x4
0x5
0x00
9d08
12810
4410
0102
0000000000000 2
0x06
8bff
128.143.137.144
128.143.71.21
Ethernet Header
IP Header
TCP Header
Ethernet frame
Application data
Ethernet Trailer
IP v.4 Addressing
An IP address is often written in dotted decimal
notation
Each byte is identified by a decimal number in
the range [0..255]:
10000000
10001111
10001001
10010000
1st Byte
2nd Byte
3rd Byte
4th Byte
= 128
= 143
= 137
= 144
128.143.137.144
Structure of an IP address
31
0
network prefix
host number
An IP address encodes both a network
number (network prefix) and an interface
number (host number).
network prefix identifies a network
the host number identifies a specific host
(actually, interface on the network).
How long the network prefix is?
Before 1993: The network prefix is implicitly
defined (class-based addressing)
After 1993: The network prefix is indicated by a
netmask.
Before 1993: Class-based addressing
The Internet address space was divided up into
classes:
Class A: Network prefix is 8 bits long
Class B: Network prefix is 16 bits long
Class C: Network prefix is 24 bits long
Class D is multicast address
Class E is reserved
Classful IP Adresses (Until 1993)
Each IP address contained a key which
identifies the class:
Class A: IP address starts with “0”
Class B: IP address starts with “10”
Class C: IP address starts with “110”
Class D: IP address starts with “1110”
Class E: IP address starts wit “11110”
The old way: Internet Address Classes
bit # 0
Class A
1
7 8
31
0
Network Prefix
Host Number
8 bits
24 bits
bit # 0 1 2
Class B
10
15 16
network id
110
host
Network Prefix
Host Number
16 bits
16 bits
bit # 0 1 2 3
Class C
31
23 24
network id
31
host
Network Prefix
Host Number
24 bits
8 bits
The old way: Internet Address Classes
bit # 0 1 2 3 4
Class D
1110
31
multicast group id
bit # 0 1 2 3 4 5
Class E
11110
31
(reserved for future use)
The old way: Internet Address Classes
Class
Leading bits Start
End
0.0.0.0 127.255.255.255
CIDR equivalent
Class A
0
/8
Class B
10
128.0.0.0 191.255.255.255
/16
Class C
110
192.0.0.0 223.255.255.255
/24
Class D (multicast)
1110
224.0.0.0 239.255.255.255
NA
Class E (reserved)
1111
240.0.0.0 255.255.255.255
NA
Problems with Classful IP Addresses
Fast growing routing table size
Each router must have an entry for every network prefix
~ 221 = 2,097,152 class C networks
In 1993, the size of routing tables started to outgrow the
capacity of routers
Other problems with classful addresses
Address depletion for large networks
Class A and Class B addresses were gone
How many class A/B network prefixes can there be?
Limited flexibility for network addresses:
Class A and B addresses are overkill (>64,000 addresses)
Class C address is insufficient (256 addresses)
Classless Inter-domain routing (CIDR) 1993
Full description RFC 1518 & 1519
Network prefix is of variable length
Addresses are allocated hierarchically
Routers aggregate multiple address prefixes into
one routing entry to minimize routing table size
CIDR network prefix is variable length
128
Addr
Mask
59
16
10000000
10001111
10001001
255
255
255
11111111
11111111
1111111
144
10010000
0
00000000
A network mask specifies the number of bits
used to identify a network in an IP address.
How?
CIDR notation
CIDR notation of an IP address:
128.143.137.144/24
/24 is the prefix length. It states that the first 24 bits are the
network prefix of the address (and the remaining 8 bits are
available for specific host addresses)
CIDR notation can nicely express blocks of addresses
An address block
[128.195.0.0, 128.195.255.255]
can be represented by an address prefix
128.195.0.0/16
How many addresses are there in a /x address block?
2 (32-x)
CIDR hierarchical address allocation
ISP
128.1.0.0/16
128.2.0.0/16
128.0.0.0/8
128.59.0.0/16
University
Foo.com
Bar.com
Library
128.59.44.0/24
128.59.16.150
CS
128.59.16.0/24
IP addresses are hierarchically allocated.
An ISP obtains an address block from a Regional Internet Registry
An ISP allocates a subdivision of the address block to an organization
An organization recursively allocates subdivision of its address block to
its networks
A host in a network obtains an address within the address block assigned
to the network
Hierarchical address allocation
128.59.16.[0 – 255]
128.59.16.150
128.59.0.0 – 128.59.255.255
128.0.0.0 - 128.255.255.255
ISP obtains an address block 128.0.0.0/8 [128.0.0.0, 128.255.255.255]
ISP allocates 128.59.0.0/16 ([128.59.0.0, 128.59.255.255]) to the
university.
University allocates 128.59.16.0/24 ([128.59.16.0, 128.59.16.255]) to the
CS department’s network
A host on the CS department’s network gets one IP address
128.59.16.150
CIDR allows route aggregation
You can reach 128.0.0.0/8 via ISP1
128.1.0.0/16
Foo.com
ISP3
ISP1
128.2.0.0/16
I
128.0.0.0/8
128.0.0.0/8 ISP1
128.59.0.0/16
Bar.com
University
Library
CS
ISP1 announces one address prefix 128.0.0.0./8 to ISP2
ISP2 can use one routing entry to reach all networks
connected to ISP1
CIDR summary
A network prefix is of variable length: a.b.c.d/x
Addresses are hierarchical allocated
Routers aggregate multiple address prefixes into
one routing entry to minimize routing table size.
Security is still an issue
Secure Routing & Path validation
What problems CIDR does not solve (I)
You can reach 128.0.0.0/8
And 204.1.0.0/16 via ISP1
ISP1
ISP2
128.0.0.0/8
204.0.0.0/8
ISP3
128.0.0.0/8
204.1.0.0/16
204.1.0.0/16 ISP1
Mutil-home.com
204.1.0.0/16
ISP1
An multi-homing site still adds one entry
into global routing tables
What problems CIDR does not solve (II)
You can reach 128.0.0.0/8
And 204.1.0.0/16 via ISP1
ISP1
ISP2
128.0.0.0/8
204.0.0.0/8
204.1.0.0/16
ISP3
128.0.0.0/8
204.1.0.0/16 ISP1
Switched.com
204.1.0.0/16
ISP1
A site switches provider without renumbering
still adds one entry into global routing tables
Global routing tables continue to grow
Source: http://bgp.potaroo.net/as4637/
Special IPv4 Addresses
Reserved or (by convention) special addresses:
Loopback interfaces
all addresses 127.0.0.1-127.255.255.255 are reserved for loopback
interfaces
Most systems use 127.0.0.1 as loopback address
loopback interface is associated with name “localhost”
Broadcast address
Host number is all ones, e.g., 128.143.255.255
Broadcast goes to all hosts on the network
Often ignored due to security concerns
Test / Experimental addresses
10.0.0.0 - 10.255.255.255
172.16.0.0 - 172.31.255.255
192.168.0.0 - 192.168.255.255
Convention (but not a reserved address)
Default gateway has host number set to ‘1’, e.g., 128.195.4.1
Special IPv4 Addresses (RFC 3330)
Addresses
CIDR
Equivalent
Purpose
RFC
Class
# of
addresses
0.0.0.0 - 0.255.255.255
0.0.0.0/8
Zero Addresses
RFC 1700
A
16,777,216
10.0.0.0 - 10.255.255.255
10.0.0.0/8
Private IP addresses
RFC 1918
A
16,777,216
127.0.0.0 - 127.255.255.255
127.0.0.0/8
Localhost Loopback
Address
RFC 1700
A
16,777,216
169.254.0.0 - 169.254.255.255
169.254.0.0/16
Zeroconf
RFC 3330
B
65,536
172.16.0.0 - 172.31.255.255
172.16.0.0/12
Private IP addresses
RFC 1918
B
1,048,576
192.0.2.0 - 192.0.2.255
192.0.2.0/24
Documentation and
Examples
RFC 3330
C
256
192.88.99.0 - 192.88.99.255
192.88.99.0/24
IPv6 to IPv4 relay
Anycast
RFC 3068
C
256
192.168.0.0 - 192.168.255.255
192.168.0.0/16
Private IP addresses
RFC 1918
C
65,536
198.18.0.0 - 198.19.255.255
198.18.0.0/15
Network Device
Benchmark
RFC 2544
C
131,072
224.0.0.0 - 239.255.255.255
224.0.0.0/4
Multicast
RFC 3171
D
268,435,456
240.0.0.0 - 255.255.255.255
240.0.0.0/4
Reserved
RFC 1700
E
268,435,456
IP Addressing (Summary)
Addressing defines how addresses are
allocated and the structure of addresses
IPv4
Classful IP addresses (obsolete)
Classless inter-domain routing (CIDR) (current
standard)
IP Version 6 addresses
IPv6 - IP Version 6
IP Version 6
Designed to be the successor to the currently used IPv4
Specification completed in 1994
Makes improvements to IPv4 (no revolutionary changes)
One (not the only !) feature of IPv6 is a significant increase in
of the IP address to 128 bits (16 bytes)
IPv6 will solve – for the foreseeable future – the problems
with IP addressing
1024 addresses per square inch on the surface of the
Earth.
IPv6 Header
32 bits
ve rs ion
(4 bits )
Traffic Clas s
(8 bits )
Flow Labe l
(24 bits )
Ne xt He ade r
(8 bits )
Payload Le ngth (16 bits )
Hop Lim its (8 bits )
Source IP addre s s (128 bits )
De s tination IP addre s s (128 bits )
Ethernet Header
IPv6 Header
TCP Header
Ethernet frame
Application data
Ethernet Trailer
Notation of IPv6 addresses
Convention: The 128-bit IPv6 address is written as eight 16bit integers (using hexadecimal digits for each integer)
CEDF:BP76:3245:4464:FACE:2E50:3025:DF12
Short notation:
Abbreviations of leading zeroes:
CEDF:BP76:0000:0000:009E:0000:3025:DF12
CEDF:BP76:0:0:9E :0:3025:DF12
“:0000:0000:0000” can be written as “::”
CEDF:BP76:0:0:FACE:0:3025:DF12
CEDF:BP76::FACE:0:3025:DF12
IPv4 address in IPv6
IPv6 addresses derived from IPv4 addresses
have 96 leading zero bits.
Convention allows to use IPv4 notation for the
last 32 bits.
::80:8F:89:90 ::128.143.137.144
IPv6 vs. IPv4: Address Comparison
IPv4 has a maximum of
232 4 billion addresses
IPv6 has a maximum of
2128 = (232)4
4 billion x 4 billion x 4 billion x 4 billion addresses
Is IPv6 widely deployed?
Data Link Layer
The main tasks of the data link layer are:
Transfer data from the network layer of one machine to the
network layer of another machine
Convert the raw bit stream of the physical layer into groups of
bits (“frames”)
Network
Layer
Data Link
Layer
Network
Layer
Data Link
Layer
Physical
Layer
Physical
Layer
TCP/IP Protocol Stack
The TCP/IP protocol stack runs on
top of multiple data link layers.
Two data link layer technologies
•Broadcast
•Point-to-Point
Application
Layer
Transport
Layer
Network
Layer
(Data) Link
Layer
Logical Link
Control (LLC)
Media Access
Control (MAC)
Sublayer in
Local Area
Networks
Two types of networks at the data link layer
Broadcast Networks: All stations share a single
communication channel
Point-to-Point Networks: Pairs of hosts (or routers) are
directly connected
Broadcast Netw ork
Point-to-Point Netw ork
Typically, local area networks (LANs) are broadcast and wide area
networks (WANs) are point-to-point
Local Area Networks
Local area networks (LANs) connect computers within a
building or a enterprise network
Almost all LANs are broadcast networks
Typical topologies of LANs are bus or ring or star
We will work with Ethernet LANs. Ethernet has a bus or
star topology.
•Bus LAN
•Ring LAN
MAC and LLC
In any broadcast network, the stations must ensure that only one
station transmits at a time on the shared communication channel
The protocol that determines who can transmit on a broadcast
channel are called Medium Access Control (MAC) protocol
The MAC protocol are implemented
in the MAC sublayer which is the
lower sublayer of the data link layer
The higher portion of the data link
to Network Layer
layer is often called Logical Link
Logical Link
Control (LLC)
Data Link
Layer
Control
Medium Access
Control
to Physical Layer
IEEE 802 Standards
IEEE 802 is a family of standards for LANs, which
defines an LLC and several MAC sublayers
IEEE 802 standard
IEEE
Reference
Model
Higher layer issues
802.1
Logical Link
Control
802.2 LLC
802.11
Wireless lan
802.5
Token ring
802.4
Token bus
802.3
CSMA/CS
Medium
Access
Control
Physical
Layer
Higher
Layer
Data Link
Layer
Physical
Layer
Ethernet
Speed:
Standard:
10Mbps -10 Gbps
802.3, Ethernet II (DIX)
Most popular physical layers for Ethernet:
10Base5
10Base2
10Base-T
100Base-TX
100Base-FX
1000Base-FX
10000Base-FX
Thick Ethernet: 10 Mbps coax cable
Thin Ethernet: 10 Mbps coax cable
10 Mbps Twisted Pair
100 Mbps over Category 5 twisted pair
100 Mbps over Fiber Optics
1Gbps over Fiber Optics
1Gbps over Fiber Optics (for wide area links)
Bus Topology
10Base5 and 10xBase2 Ethernets has a bus
topology
Ethernet
Star Topology
Starting with 10Base-T, stations are connected
to a hub in a star configuration
Hub
Ethernet Hubs vs. Ethernet Switches
An Ethernet switch is a packet switch for Ethernet frames
Buffering of frames prevents collisions.
Each port is isolated and builds its own collision domain
An Ethernet Hub does not perform buffering:
Collisions occur if two frames arrive at the same time.
Hub
Switch
CSMA/CD
CSMA/CD
CSMA/CD
CSMA/CD
CSMA/CD
CSMA/CD
CSMA/CD
CSMA/CD
CSMA/CD
CSMA/CD
CSMA/CD
CSMA/CD
CSMA/CD
HighSpeed
Backplane
CSMA/CD
Input
Buf fers
CSMA/CD
CSMA/CD
Output
Buf fers
Ethernet and IEEE 802.3: Any Difference?
There are two types of Ethernet frames in use, with
subtle differences:
“Ethernet” (Ethernet II, DIX (Digital-Intel-Xerox)
802.3:
An industry standards from 1982 that is based on the first
implementation of CSMA/CD by Xerox.
Predominant version of CSMA/CD in the US.
IEEE’s version of CSMA/CD from 1985.
Interoperates with 802.2 (LLC) as higher layer.
Difference for our purposes: Ethernet and 802.3 use
different methods to encapsulate an IP datagram.
Ethernet II, DIX Encapsulation (RFC 894)
802.3 MAC
destination
address
source
address
type
data
CRC
6
6
2
46-1500
4
0800
IP datagram
2
38-1492
0806
2
0835
2
ARP request/reply PAD
28
10
RARP request/reply PAD
28
10
IEEE 802.2/802.3 Encapsulation (RFC 1042)
802.3 MAC
802.2 LLC
destination
address
source
address
length
6
6
2
DSAP SSAP
AA
AA
1
1
802.2 SNAP
cntl
03
org code
0
type
data
CRC
1
3
2
38-1492
4
0800
IP datagram
2
38-1492
- destination address, source address:
MAC addresses are 48 bit
- length: frame length in number of bytes
- DSAP, SSAP: always set to 0xaa
- Ctrl:
set to 3
- org code: set to 0
- type field identifies the content of the
data field
- CRC:
cylic redundancy check
0806
2
0835
2
ARP request/reply PAD
28
10
RARP request/reply PAD
28
10
Point-to-Point (serial) links
Many data link connections are
point-to-point serial links:
Dial-in or DSL access connects hosts
to access routers
Routers are connected by
high-speed point-to-point links
Here, IP hosts and routers are
connected by a serial cable
Data link layer protocols for
point-to-point links are simple:
Main role is encapsulation of IP
datagrams
No media access control needed
Acce s s
Route r
M ode m s
Dial-Up Access
Router
Router
Router
Point-to-Point Links
Router
Data Link Protocols for Point-to-Point links
SLIP (Serial Line IP)
PPP (Point-to-Point Protocol):
•
•
First protocol for sending IP datagrams over dial-up links (from
1988)
Encapsulation, not much else
Successor to SLIP (1992), with added functionality
Used for dial-in and for high-speed routers
HDLC (High-level Data Link Control) :
•
•
•
Widely used and influential standard (1979)
Default protocol for serial links on Cisco routers
Actually, PPP is based on a variant of HDLC
PPP - IP encapsulation
The frame format of PPP is similar to HDLC and the 802.2 LLC frame
format:
flag
addr ctrl
7E
FF
03
1
1
1
protocol
data
CRC
flag
7E
2
<= 1500
0021
IP datagram
C021
link control data
8021
network control data
PPP assumes a duplex circuit
Note: PPP does not use addresses
Usual maximum frame size is 1500
2
1
Additional PPP functionality
In addition to encapsulation, PPP supports:
multiple network layer protocols (protocol multiplexing)
Link configuration
Link quality testing
Error detection
Option negotiation
Address notification
Authentication
The above functions are supported by helper protocols:
LCP
PAP, CHAP
NCP
PPP Support protocols
Link management: The link control protocol (LCP) is
responsible for establishing, configuring, and negotiating
a data-link connection. LCP also monitors the link quality
and is used to terminate the link.
Authentication: Authentication is optional. PPP
supports two authentication protocols: Password
Authentication Protocol (PAP) and Challenge Handshake
Authentication Protocol (CHAP).
Network protocol configuration: PPP has network
control protocols (NCPs) for numerous network layer
protocols. The IP control protocol (IPCP) negotiates IP
address assignments and other parameters when IP is
used as network layer.
Address Resolution Protocol
(ARP)
Overview
TCP
UDP
ICMP
IP
IGMP
ARP
Network
Access
RARP
Media
Transport
Layer
Network
Layer
Link Layer
ARP and RARP
Note:
The Internet is based on IP addresses
Data link protocols (Ethernet, FDDI, ATM) may have different
(MAC) addresses
The ARP and RARP protocols perform the translation
between IP addresses and MAC layer addresses
We will discuss ARP for broadcast LANs, particularly
Ethernet LANs
IP address
(32 bit)
ARP
RARP
Ethernet MAC
address
(48 bit)
Processing of IP packets by network device drivers
IP Input
IP Output
Put on IP
input queue
Yes
Yes
IP destination = multicast
or broadcast ?
No
IP destination of packet
= local IP address ?
loopback
Driver
Put on IP
input queue
No: get MAC
address with
ARP
Ethernet
Ethernet
Driver
ARP
ARP
Packet
IP datagram
demultiplex
Ethernet Frame
Address Translation with ARP
ARP Request:
Argon broadcasts an ARP request to all stations on the network:
“What is the hardware address of 128.143.137.1?”
Argon
128.143.137.144
00:a0:24:71:e4:44
ARP Request:
What is the MAC address
of 128.143.71.1?
Router137
128.143.137.1
00:e0:f9:23:a8:20
Address Translation with ARP
ARP Reply:
Router 137 responds with an ARP Reply which contains
the hardware address
Argon
128.143.137.144
00:a0:24:71:e4:44
Router137
128.143.137.1
00:e0:f9:23:a8:20
ARP Reply:
The MAC address of 128.143.71.1
is 00:e0:f9:23:a8:20
ARP Packet Format
Ethernet II header
Destination
address
Source
address
Type
0x8060
6
6
2
ARP Request or ARP Reply
28
10
Hardware type (2 bytes)
Hardware address
length (1 byte)
Padding
CRC
4
Protocol type (2 bytes)
Protocol address
length (1 byte)
Operation code (2 bytes)
Source hardware address*
Source protocol address*
Target hardware address*
Target protocol address*
* Note: The length of the address fields is determined by the corresponding address length fields
Example
ARP Request from Argon:
Source hardware address:
Source protocol address:
Target hardware address:
Target protocol address:
00:a0:24:71:e4:44
128.143.137.144
00:00:00:00:00:00
128.143.137.1
ARP Reply from Router137:
Source hardware address:
Source protocol address:
Target hardware address:
Target protocol address:
00:e0:f9:23:a8:20
128.143.137.1
00:a0:24:71:e4:44
128.143.137.144
ARP Cache
Since sending an ARP request/reply for each IP
datagram is inefficient, hosts maintain a cache (ARP
Cache) of current entries. The entries expire after a time
interval.
Contents of the ARP Cache:
(128.143.71.37) at 00:10:4B:C5:D1:15 [ether] on eth0
(128.143.71.36) at 00:B0:D0:E1:17:D5 [ether] on eth0
(128.143.71.35) at 00:B0:D0:DE:70:E6 [ether] on eth0
(128.143.136.90) at 00:05:3C:06:27:35 [ether] on eth1
(128.143.71.34) at 00:B0:D0:E1:17:DB [ether] on eth0
(128.143.71.33) at 00:B0:D0:E1:17:DF [ether] on eth0
Proxy ARP
Proxy ARP: Host or router responds to ARP Request that arrives
from one of its connected networks for a host that is on another of its
connected networks.
Things to know about ARP
What happens if an ARP Request is made for a nonexisting host?
Several ARP requests are made with increasing time intervals
between requests. Entually, ARP gives up (timeout).
On some systems (including Linux) a host periodically
sends ARP Requests for all addresses listed in the ARP
cache. This refreshes the ARP cache content, but also
introduces traffic.
Gratuitous ARP Requests: A host sends an ARP request
for its own IP address:
Useful for detecting if an IP address has already been assigned.
Vulnerabilities of ARP
1.
Since ARP does not authenticate requests or replies,
ARP Requests and Replies can be forged
2.
ARP is stateless: ARP Replies can be sent without a
corresponding ARP Request
3.
According to the ARP protocol specification, a node
receiving an ARP packet (Request or Reply) must
update its local ARP cache with the information in the
source fields, if the receiving node already has an entry
for the IP address of the source in its ARP cache. (This
applies for ARP Request packets and for ARP Reply
packets)
Vulnerabilities of ARP
Typical exploitation of these vulnerabilities:
A forged ARP Request or Reply can be used to update
the ARP cache of a remote system with a forged entry
(ARP Poisoning)
This can be used to redirect IP traffic to other hosts
Some notes on Lab 2
What is a single-segment network?
128.59.1.100
128.59.1.200
128.59.1.300
128.59.2.0/24
128.59.1.0/24
128.59.1.1
128.59.2.100
128.59.2.1
128.59.3.1
128.59.2.200
128.59.3.0/24
128.59.3.100
128.59.3.200
A single-segment network consists of interfaces
connected by a single physical link, either a point-topoint link or a broadcast link.
Interfaces on the same single-segment network have
the same network prefix.
How to identify a single segment IP network
128.59.2.100
128.59.1.100
128.59.1.200
128.59.1.300
128.59.1.1
128.59.3.1
128.59.2.200
128.59.3.100
128.59.2.1
128.59.3.200
Detach interfaces from routers or hosts
Each isolated island is a single segment IP network
Each interface on the same single segment IP network
must have the same network address prefix
Protocol specification vs implementation
According to the ARP protocol specification, a node
receiving an ARP packet (Request or Reply) must
update its local ARP cache with the information in the
source fields, if the receiving node already has an entry
for the IP address of the source in its ARP cache. (This
applies for ARP Request packets and for ARP Reply
packets)
Implementation may differ from the specification
What you observe in the lab may not be universally
true.