Transcript Parallel ports power supply and the clock oscillator

Parallel ports, power supply, and
the clock oscillator
Chapter Three
Dr. Gheith Abandah
1
Outline
• Parallel ports
– Technical challenges
– Connecting to the parallel port
– The PIC 16F84A parallel ports
• Power supply
• Clock oscillator
Dr. Gheith Abandah
2
Data Transfer
• Almost any embedded system needs to transfer
digital data between its CPU and the outside world.
– Direct user interface, including switches, keypads, lightemitting diodes (LEDs) and displays
– Input measurement information, from external sensors,
possibly being acquired through an analog-to-digital
converter
– Output control information, for example to motors or
other actuators
– Bulk data transfer to or from other systems or subsystems,
moving in serial or parallel form, for example sending
serial data to an external memory.
Dr. Gheith Abandah
3
Output Parallel Ports
Dr. Gheith Abandah
4
Input Parallel Ports
Dr. Gheith Abandah
5
Bi-directional Parallel Ports
Dr. Gheith Abandah
6
Port electrical characteristics
Modeling a logic gate output.
(a) Generalized model. (b) Model of CMOS logic gate output
Dr. Gheith Abandah
7
Schmitt trigger inputs
Schmitt trigger characteristics.
(a) Buffer with Schmitt trigger input. (b) Input/output characteristic
Dr. Gheith Abandah
8
The ‘Open Drain’ output
(a) An ‘Open
Drain’ output.
(b) Open Drain
output driving
load resistor.
(c) The ‘WiredOR’ connection
Dr. Gheith Abandah
9
Connecting to the parallel port
(1) Switches
(a) SPDT connection. (b) SPST with pull-up resistor.
(c) SPST with pull-down resistor
Pull-up values in the range 10–100 kΩ
Dr. Gheith Abandah
10
Connecting to the parallel port
(2) Light-emitting diodes
Dr. Gheith Abandah
11
Connecting to the parallel port
(2) Light-emitting diodes
Driving LEDs from logic gates.
(a) Gate output sourcing current to LED
(b) Gate output sinking current from LED
Dr. Gheith Abandah
12
Connecting to the parallel port
(2) Light-emitting diodes
Dr. Gheith Abandah
13
The PIC 16F84A parallel ports
• Port A – 5 Bits
– RA3:RA0
– RA4/T0CKI
• Port B – 8 Bits
– RB0/INT
– RB3:RB1
– RB7:RB4: Interrupt on change
Dr. Gheith Abandah
14
Dr. Gheith Abandah
15
Dr. Gheith Abandah
16
Dr. Gheith Abandah
17
Dr. Gheith Abandah
18
Port output characteristics -1
R = 130 Ω
VOH vs. IOH (VDD = 3V, −40 to 125◦C)
Dr. Gheith Abandah
19
Port output characteristics -2
VOL vs. IOL (VDD = 3V, −40 to 125◦C)
R = 36 Ω
Dr. Gheith Abandah
20
The clock oscillator
• Faster clock gives faster execution, but more
power consumption.
• The clock oscillator must give stable and
accurate clock signal.
• Oscillator types:
– Resistor–capacitor (RC)
• Not precise
– Crystal or ceramic
• Precise frequency, fragile, should be near the MC
Dr. Gheith Abandah
21
Oscillator types
(a) Resistor–capacitor (RC).
Dr. Gheith Abandah
(b) Crystal or ceramic
22
The 16F84A clock oscillator
• Types:
1) XT – crystal: 1-4 MHz
2) HS – high speed: >= 4 MHz, with ceramic
resonators.
3) LP – low power: <= 200 KHz, e.g., 32.768 kHz
(i.e. 215),
4) RC – resistor-capacitor
Dr. Gheith Abandah
23
(a) Crystal or ceramic, HS, XT or LP. (b) Resistor–
capacitor. (c) Externally supplied clock
Dr. Gheith Abandah
24
Data Sheet Information
Dr. Gheith Abandah
25
Power Supply
RC
Oscillator
100 nF
decoupling
capacitor
Dr. Gheith Abandah
26
Dr. Gheith Abandah
27
16F84A operating conditions
Summary – 1
• The parallel port allows ready exchange of digital data
between the outside world and the controller CPU.
• It is important to understand the electrical
characteristics of the parallel port and how they
interact with external elements.
• While there is considerable diversity in the logic design
of ports, they tend to follow similar patterns.
• The internal circuitry is worth understanding, as it
leads to effective use of ports.
• The 16F84A has diverse and flexible parallel ports.
Dr. Gheith Abandah
28
Summary – 2
• A microcontroller needs a clock signal in order to
operate. The characteristics of the clock oscillator
determine speed of operation and timing stability, and
strongly influence power consumption. Active
elements of the oscillator are usually built in to a
microcontroller, but the designer must select the
oscillator type, and its frequency and configuration.
• A microcontroller needs a power supply in order to
operate. The requirements need to be understood and
must be met by a supply of the appropriate type.
Dr. Gheith Abandah
29